View HYS64T64000HU-3S-A_4538324.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

May 2007
HYS64T32x00HU-[3/3S/3.7/5]-A HYS[64/72]T64x00HU-[3/3S/3.7/5]-A HYS[64/72]T128x20HU-[3/3S/3.7/5]-A
240-Pin Unbuffered DDR2 SDRAM Modules DDR2 SDRAM RoHS Compliant
Internet Data Sheet
Rev. 1.41
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32x00HU-[3/3S/3.7/5]-A, HYS[64/72]T64x00HU-[3/3S/3.7/5]-A, HYS[64/72]T128x20HU-[3/3S/3.7/5]-A Revision History: 2007-01, Rev. 1.41 Page All 42, 43 All All 43, 44, 45, 46 29, 34, 37 48 Subjects (major changes since last revision) Adapted internet edition Table 30 Footnote 4 updated. Added Products HYS64T[32/64/128]9x0HU-[3S/3.7]-A Qimonda update Editorial changes Updated AC Timing Parameter table DQS DQ skew value is the max. value Added 50 ohm data
Previous Revision: 2007-01, Rev. 1.40 Previous Revision: 2006-09, Rev. 1.32 Previous Revision: 2006-03, Rev. 1.31
Previous Revision: 2005-08, Rev. 1.3
We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc@qimonda.com
qag_techdoc_rev400 / 3.2 QAG / 2006-08-07 03292006-EZUJ-JY4S
2
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
1
Overview
This chapter gives an overview of the 240-Pin Unbuffered DDR2 SDRAM Modules product family and describes its main characteristics.
1.1
Features
* Programmable CAS Latencies (3, 4 and 5), Burst Length (8 & 4) and Burst Type * Auto Refresh (CBR) and Self Refresh * All inputs and outputs SSTL_1.8 compatible * Off-Chip Driver Impedance Adjustment (OCD) and On-Die Termination (ODT) * Serial Presence Detect with E2PROM * Dimensions (nominal): 30 mm high, 133.35 mm wide * Based on standard reference layouts Raw Card "A", "B""C","D","E","F" and "G" * RoHS compliant products1)
* 240-Pin PC2-5300, PC2-4200 and PC2-3200 DDR2 SDRAM memory modules for use as main memory when installed in systems such as mobile personal computers. * 32M x 64, 64M x 64, 64M x 72, 128M x 64, 128M x 72 module organization, and 32M x 16, 64M x 8 chip organization * 256 MByte, 512 MByte and 1 GByte modules built with 512-Mbit DDR2 SDRAMs in P-TFBGA-60 and P-TFBGA84 chipsize packages * All Speed grades faster than DDR2-400 comply with DDR2-400 timing specifications. * Standard Double-Data-Rate-Two Synchronous DRAMs (DDR2 SDRAM) with a single + 1.8 V ( 0.1 V) power supply
TABLE 1
Performance table for -3(S)
Product Type Speed Code Speed Grade Max. Clock Frequency @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time -3 PC2-5300 4-4-4 -3S PC2-5300 5-5-5 333 266 200 15 15 45 60 Unit -- MHz MHz MHz ns ns ns ns
fCK5 fCK4 fCK3 tRCD tRP tRAS tRC
333 333 200 12 12 45 57
1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
3
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 2
Performance table for -3.7
Product Type Speed Code Speed Grade Max. Clock Frequency @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time -3.7 PC2-4200 4-4-4 Unit -- MHz MHz MHz ns ns ns ns
fCK5 fCK4 fCK3 tRCD tRP tRAS tRC
266 266 200 15 15 45 60
TABLE 3
Performance table for -5
Product Type Speed Code Speed Grade max. Clock Frequency @CL5 @CL4 @CL3 min. RAS-CAS-Delay min. Row Precharge Time min. Row Active Time min. Row Cycle Time fCK5 fCK4 fCK3 tRCD tRP tRAS tRC -5 PC2-3200 3-3-3 200 200 200 15 15 40 55 Unit -- MHz MHz MHz ns ns ns ns
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
4
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
1.2
Description
The memory array is designed with 512-Mbit Double-DataRate-Two (DDR2) Synchronous DRAMs. Decoupling capacitors are mounted on the PCB board. The DIMMs feature serial presence detect based on a serial E2PROM device using the 2-pin I2C protocol. The first 128 bytes are programmed with configuration data and are write protected; the second 128 bytes are available to the customer.
The Qimonda HYS[64/72]T[32/64/128]0x0HU-[3/.../5]-A module family are unbuffered DIMM modules "UDIMMs" with 30,0 mm height based on DDR2 technology. DIMMs are available as non-ECC modules in 32M x 64 (256MB), 64M x 64 (512MB), 128M x 64 (1GB) and as ECC modules in 64M x 72 (512MB), 128M x 72 (1GB) organization and density, intended for mounting into 240-pin connector sockets.
TABLE 4
Ordering Information for RoHS Compliant Products
Product Type1) PC2-5300 HYS64T32000HU-3-A HYS64T64000HU-3-A HYS72T64000HU-3-A HYS64T128020HU-3-A HYS72T128020HU-3-A HYS64T32000HU-3S-A HYS64T32900HU-3S-A HYS64T64000HU-3S-A HYS64T64900HU-3S-A HYS72T64000HU-3S-A HYS64T128020HU-3S-A HYS64T128920HU-3S-A HYS72T128020HU-3S-A PC2-4200 HYS64T32000HU-3.7-A HYS64T32900HU-3.7-A HYS64T64000HU-3.7-A HYS64T64900HU-3.7-A HYS72T64000HU-3.7-A HYS64T128020HU-3.7-A HYS64T128920HU-3.7-A HYS72T128020HU-3.7-A PC2-3200 HYS64T32000HU-5-A HYS64T64000HU-5-A HYS72T64000HU-5-A 256MB 1Rx16 PC2-3200U-333-11-C1 512MB 1Rx8 PC2-3200U-333-11-A1 512MB 1Rx8 PC2-3200E-333-11-A1 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, ECC 512 Mbit (x16) 512 Mbit (x8) 512 Mbit (x8) 256MB 1Rx16 PC2-4200U-444-11-C1 256MB 1Rx16 PC2-4200U-444-11-C1 512MB 1Rx8 PC2-4200U-444-11-A1 512MB 1Rx8 PC2-4200U-444-11-D0 512MB 1Rx8 PC2-4200E-444-11-A1 1GB 2Rx8 PC2-4200U-444-11-B1 1GB 2Rx8 PC2-4200U-444-11-E0 1GB 2Rx8 PC2-4200E-444-11-B1 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, ECC 2 Ranks, Non-ECC 2 Ranks, Non-ECC 2 Ranks, ECC 512 Mbit (x16) 512 Mbit (x16) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 256MB 1Rx16 PC2-5300U-444-12-C1 512MB 1Rx8 PC2-5300U-444-12-D0 512MB 1Rx8 PC2-5300E-444-12-F0 1GB 2Rx8 PC2-5300U-444-12-E0 1GB 2Rx8 PC2-5300E-444-12-G0 256MB 1Rx16 PC2-5300U-555-12-C1 256MB 1Rx16 PC2-5300U-555-12-C1 512MB 1Rx8 PC2-5300U-555-12-D0 512MB 1Rx8 PC2-5300U-555-12-D0 512MB 1Rx8 PC2-5300E-555-12-F0 1GB 2Rx8 PC2-5300U-555-12-E0 1GB 2Rx8 PC2-5300U-555-12-E0 1GB 2Rx8 PC2-5300E-555-12-G0 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, ECC 2 Ranks, Non-ECC 2 Ranks, ECC 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, Non-ECC 1 Rank, ECC 2 Ranks, Non-ECC 2 Ranks, Non-ECC 2 Ranks, ECC 512 Mbit (x16) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x16) 512 Mbit (x16) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) 512 Mbit (x8) Compliance Code2) Description SDRAM Technology
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
5
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Product Type1) HYS64T128020HU-5-A HYS72T128020HU-5-A
Compliance Code2) 1GB 2Rx8 PC2-3200U-333-11-B1 1GB 2Rx8 PC2-3200E-333-12-B1
Description 2 Ranks, Non-ECC 2 Ranks, ECC
SDRAM Technology 512 Mbit (x8) 512 Mbit (x8)
1) All product types end with a place code, designating the silicon die revision. Example: HYS64T64000HU-3-A, indicating Rev. "A" dies are used for DDR2 SDRAM components. For all Qimonda DDR2 module and component nomenclature see Chapter 6 of this data sheet. 2) The Compliance Code is printed on the module label and describes the speed grade, for example "PC2-5300U-444-12-C1", where 4200U means Unbuffered DIMM modules with 4.26 GB/sec Module Bandwidth and "444-12" means Column Address Strobe (CAS) latency = 4, Row Column Delay (RCD) latency = 4 and Row Precharge (RP) latency = 4 using the latest JEDEC SPD Revision 1.2 and produced on the Raw Card "C".
TABLE 5
Address Format
DIMM Density 256 MByte 512 MByte 512 MByte 1 GByte 1 GByte Module Organization 32M x64 64M x64 64M x72 128M x64 128M x72 Memory Ranks 1 1 1 2 2 ECC/ Non-ECC Non-ECC Non-ECC ECC Non-ECC ECC # of SDRAMs # of row/bank/column bits 4 8 9 16 18 13/2/10 14/2/10 14/2/10 14/2/10 14/2/10 Raw Card C A,D A,F B,E B,G
TABLE 6
Components on Modules
Product Type1) HYS64T32000HU HYS64T32900HU HYS64T64000HU HYS64T64900HU HYS72T64000HU HYS64T128020HU HYS64T128920HU HYS72T128020HU DRAM Components1) HYB18T512160AF HYB18T512160AF HYB18T512800AF HYB18T512800AF HYB18T512800AF HYB18T512800AF HYB18T512800AF HYB18T512800AF DRAM Density 512 Mbit 512 Mbit 512 Mbit 512 Mbit 512 Mbit 512 Mbit 512 Mbit 512 Mbit DRAM Organisation 32M x 16 32M x 16 64M x 8 64M x 8 64M x 8 64M x 8 64M x 8 64M x 8 Notes2)
1) Green Product 2) For a detailed description of all functionalities of the DRAM components on these modules see the component data sheet.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
6
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
2
Pin Configurations
This chapter contains information to the pin configuration of the modules as well as the block diagrams to the various module organization The pin configuration of the Unbuffered DDR2 SDRAM DIMM and Table 9 respectively. The pin numbering is depicted in is listed by function in Table 7 (240 pins). The abbreviations Figure 1 for non-ECC modules (x64) and Figure 2 for ECC used in columns Pin and Buffer Type are explained in Table 8 modules (x72).
TABLE 7
Pin Configuration of UDIMM
Ball No. Clock Signals 185 137 220 186 138 221 52 171 CK0 CK1 CK2 CK0 CK1 CK2 CKE0 CKE1 NC Control Signals 193 76 S0# S1# NC 192 74 73 Address Signals 71 190 54 BA0 BA1 BA2 NC I I I NC SSTL SSTL SSTL -- Bank Address Bus 2 Not Connected Less than 1Gb DDR2 SDRAMS Bank Address Bus 1:0 RAS CAS WE I I NC I I I SSTL SSTL -- SSTL SSTL SSTL Not Connected Note: 1 Rank module Row Address Strobe Column Address Strobe Write Enable Chip Select Rank 1:0 I I I I I I I I NC SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL -- Not Connected Note: 1 Rank module Clock Enable Rank 1:0 Clock Signals 2:0, Complement Clock Signals 2:0 Name Pin Type Buffer Type Function
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
7
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Ball No. 188 183 63 182 61 60 180 58 179 177 70 57 176 196
Name A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 AP A11 A12 A13 NC
Pin Type I I I I I I I I I I I I I I I NC I NC
Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL -- SSTL --
Function Address Bus 12:0
Address Signal 13 Note: 1 Gbit based module and 512M x4/x8 Not Connected Note: Module based on 1 Gbit x16 Module based on 512 Mbit x16 or smaller Address Signal 14 Note: Modules based on 2 Gbit Not Connected Note: Modules based on 1 Gbit or smaller Data Bus 63:0 Data Input/Output pins
174
A14 NC
Data Signals 3 4 9 10 122 123 128 129 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 I/O I/O I/O I/O I/O I/O I/O I/O SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
8
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Ball No. 12 13 21 22 131 132 140 141 24 25 30 31 143 144 149 150 33 34 39 40 152 153 158 159 80 81 86 87 199 200 205 206 89 90 95 96 208 209 214 215
Name DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47
Pin Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL
Function Data Bus 63:0 Data Input/Output pins
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
9
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Ball No. 98 99 107 108 217 218 226 227 110 111 116 117 229 230 235 236 Check Bit Signals 42
Name DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 CB0 NC
Pin Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O NC I/O NC I/O NC I/O NC I/O NC I/O NC
Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL -- SSTL -- SSTL -- SSTL -- SSTL -- SSTL --
Function Data Bus 63:0 Data Input/Output pins
Check Bit 0 Note: ECC type module only Not Connected Note: ECC type module only Check Bit 1 Note: ECC type module only Not Connected Note: ECC type module only Check Bit 2 Note: ECC type module only Not Connected Note: ECC type module only Check Bit 3 Note: ECC type module only Not Connected Note: ECC type module only Check Bit 4 Note: ECC type module only Not Connected Note: ECC type module only Check Bit 5 Note: ECC type module only Not Connected Note: ECC type module only
43
CB1 NC
48
CB2 NC
49
CB3 NC
161
CB4 NC
162
CB5 NC
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
10
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Ball No. 167
Name CB6 NC
Pin Type I/O NC I/O NC
Buffer Type SSTL -- SSTL --
Function Check Bit 6 Note: ECC type module only Not Connected Note: ECC type module only Check Bit 7 Note: ECC type module only Not Connected Note: Non-ECC module Data Strobe Bus 8:0
168
CB7 NC
Data Strobe Bus 7 16 28 37 84 93 105 114 46 6 15 27 36 83 92 104 113 45 Data Mask Signals 125 134 146 155 202 211 223 232 164 EEPROM 120 119 SCL SDA I I/O CMOS OD Serial Bus Clock Serial Bus Data DM0 DM1 DM2 DM3 DM4 DM5 DM6 DM7 DM8 I I I I I I I I I SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Data Mask Bus 8:0 DQS0 DQS1 DQS2 DQS3 DQS4 DQS5 DQS6 DQS7 DQS8 DQS0 DQS1 DQS2 DQS3 DQS4 DQS5 DQS6 DQS7 DQS8 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Complement Data Strobe Bus 8:0
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
11
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Ball No. 239 240 101 Power Supplies 1 238 51,56,62,72,75,, 78,170,175,181,, 191,194 53,59,64,67,69,, 172,178,184,187, 189,197 2,5,8,11,14,17,, 20,23,26,29,32, 35,38,41,44,47,, 50,65,66,79,82, 85,88,91,94,97,, 100,103,106, 109,112,115,118, 121,124,127,, 130,133,136,139, 142,145,148,, 151,154,157,160, 163,166,169, 198,201,204,207, 210,213,216,, 219,222,225,228, 231,234,237 Other Pins 195 77
Name SA0 SA1 SA2
Pin Type I I I
Buffer Type CMOS CMOS CMOS -- -- --
Function Serial Address Select Bus 2:0
VREF AI VDDSPD PWR VDDQ PWR
I/O Reference Voltage EEPROM Power Supply I/O Driver Power Supply
VDD
PWR
--
Power Supply
VSS
GND
--
Ground Plane
ODT0 ODT1 NC
I I NC NC
SSTL SSTL -- --
On-Die Termination Control 0 On-Die Termination Control 1 Note: 2 Rank modules Not Connected Note: 1 Rank modules Not connected Note: Pins not connected on Qimonda UDIMMs
18,19,55,68,102,1 NC 26,135,147, 156,165,173,203, 212, 224,233
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
12
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 8
Abbreviations for Pin Type
Abbreviation I O I/O AI PWR GND NC Description Standard input-only pin. Digital levels. Output. Digital levels. I/O is a bidirectional input/output signal. Input. Analog levels. Power Ground Not Connected
TABLE 9
Abbreviations for Buffer Type
Abbreviation SSTL LV-CMOS CMOS OD Description Serial Stub Terminated Logic (SSTL_18) Low Voltage CMOS CMOS Levels Open Drain. The corresponding pin has 2 operational states, active low and tri-state, and allows multiple devices to share as a wire-OR.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
13
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Pin Configuration UDIMM x64 (240 Pin)
FIGURE 1
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
14
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Pin Configuration UDIMM x72 (240 Pin)
FIGURE 2
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
15
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
3
3.1
Electrical Characteristics
Absolute Maximum Ratings
TABLE 10
Absolute Maximum Ratings
This chapter contains the electrical characteristics.
Caution is needed not to exceed absolute maximum ratings of the DRAM device listed in Table 10 at any time.
Symbol
Parameter
Rating Min. Max. +2.3 +2.3 +2.3 +2.3
Unit
Notes
Storage Temperature -55 +100 1) When VDD and VDDQ and VDDL are less than 500 mV; VREF may be equal to or less than 300 mV.
2) Storage Temperature is the case surface temperature on the center/top side of the DRAM.
VDD VDDQ VDDL VIN, VOUT TSTG
Voltage on VDD pin relative to VSS Voltage on VDDQ pin relative to VSS Voltage on VDDL pin relative to VSS Voltage on any pin relative to VSS
-1.0 -0.5 -0.5 -0.5
V V V V C
1) 1)2) 1)2) 1) 1)2)
Attention: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
TABLE 11
DRAM Component Operating Temperature Range
Symbol Parameter Rating Min. Max. 95 C
1)2)3)4)
Unit
Notes
TOPER
Operating Temperature
0
1) Operating Temperature is the case surface temperature on the center / top side of the DRAM. 2) The operating temperature range are the temperatures where all DRAM specification will be supported. During operation, the DRAM case temperature must be maintained between 0 - 95 C under all other specification parameters. 3) Above 85 C the Auto-Refresh command interval has to be reduced to tREFI= 3.9 s 4) When operating this product in the 85 C to 95 C TCASE temperature range, the High Temperature Self Refresh has to be enabled by setting EMR(2) bit A7 to "1". When the High Temperature Self Refresh is enabled there is an increase of IDD6 by approximately 50%
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
16
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
3.2
DC Operating Conditions
TABLE 12
Operating Conditions
This chapter contains the DC operating conditions tables.
Parameter
Symbol
Values Min. Max. +65 +95 +100 +105 90
Unit
Notes
Operating temperature (ambient) DRAM Case Temperature Storage Temperature Barometric Pressure (operating & storage) Operating Humidity (relative)
1) 2) 3) 4)
TOPR TCASE TSTG
PBar
0 0 - 50 +69 10
xC xC xC kPa %
5) 1)2)3)4)
HOPR
DRAM Component Case Temperature is the surface temperature in the center on the top side of any of the DRAMs. Within the DRAM Component Case Temperature Range all DRAM specifications will be supported Above 85 C DRAM Case Temperature the Auto-Refresh command interval has to be reduced to tREFI = 3.9 s Self-Refresh period is hard-coded in the DRAMs and therefore it is imperative that the system ensures the DRAM is below 85 C Case Temperature before initiating Self-Refresh operation. 5) Up to 3000 m.
TABLE 13
Supply Voltage Levels and DC Operating Conditions
Parameter Symbol Values Min. Device Supply Voltage Output Supply Voltage Input Reference Voltage SPD Supply Voltage DC Input Logic High DC Input Logic Low Nom. 1.8 1.8 0.5 x VDDQ -- -- -- Max. 1.9 1.9 0.51 x VDDQ 3.6 V V V V V V
3) 1) 2)
Unit
Notes
VDD VDDQ VREF VDDSPD VIH(DC)
VIL(DC)
1.7 1.7 0.49 x VDDQ 1.7
VREF + 0.125
- 0.30
VDDQ + 0.3 VREF - 0.125
In / Output Leakage Current IL -5 -- 5 A 1) Under all conditions, VDDQ must be less than or equal to VDD 2) Peak to peak AC noise on VREF may not exceed 2% VREF (DC).VREF is also expected to track noise in VDDQ. 3) Input voltage for any connector pin under test of 0 V VIN VDDQ + 0.3 V; all other pins at 0 V. Current is per pin
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
17
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
3.3
AC Characteristics
This chapter contains the AC operating conditions tables.
3.3.1
Speed Grade Definitions
List of speed grade definition tables. * Table 14 "Speed Grade Definition Speed Bins for DDR2-667" on Page 18 * Table 15 "Speed Grade Definition Speed Bins for DDR2-533C" on Page 19 * Table 16 "Speed Grade Definition Speed Bins for DDR2-400B" on Page 19
TABLE 14
Speed Grade Definition Speed Bins for DDR2-667
Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Symbol DDR2-667C -3 4-4-4 Min. 5 3 3 45 57 12 12 Max. 8 8 8 70000 -- -- -- DDR2-667D -3S 5-5-5 Min. 5 3.75 3 45 60 15 15 Max. 8 8 8 70000 -- -- -- Unit Notes
tCK
-- ns ns ns ns ns ns ns
1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4)
tCK tCK tCK tRAS tRC tRCD tRP
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) . 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
18
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 15
Speed Grade Definition Speed Bins for DDR2-533C
Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Symbol DDR2-533C -3.7 4-4-4 Min. 5 3.75 3.75 45 60 15 15 Max. 8 8 8 70000 -- -- -- Unit Note
tCK
-- ns ns ns ns ns ns ns
1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4)
Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time
tCK tCK tCK tRAS tRC tRCD tRP
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI.
TABLE 16
Speed Grade Definition Speed Bins for DDR2-400B
Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Symbol DDR2-400B -5 3-3-3 Min. 5 5 5 40 55 15 15 Max. 8 8 8 70000 -- -- -- Unit Note
tCK
-- ns ns ns ns ns ns ns
1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4)
Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time
tCK tCK tCK tRAS tRC tRCD tRP
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
19
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
3.3.2
AC Timing Parameters
List of AC Timing parameters. * Table 17 "Timing Parameter by Speed Grade - DDR2-667" on Page 20 * Table 18 "Timing Parameter by Speed Grade - DDR2-533" on Page 25 * Table 19 "Timing Parameter by Speed Grade - DDR2-400" on Page 28
TABLE 17
Timing Parameter by Speed Grade - DDR2-667
Parameter Symbol DDR2-667 Min. Max. +450 +400 0.52 0.52 8000 -- -- -- -- ps ps
9) 9) 10)11) 10)11)
Unit
Notes1)2)3)4)5)6)
7)8)
tAC DQS output access time from CK / CK tDQSCK Average clock high pulse width tCH.AVG Average clock low pulse width tCL.AVG Average clock period tCK.AVG DQ and DM input setup time tDS.BASE DQ and DM input hold time tDH.BASE Control & address input pulse width for each input tIPW DQ and DM input pulse width for each input tDIPW Data-out high-impedance time from CK / CK tHZ DQS/DQS low-impedance time from CK / CK tLZ.DQS DQ low impedance time from CK/CK tLZ.DQ DQS-DQ skew for DQS & associated DQ signals tDQSQ CK half pulse width tHP
DQ output access time from CK / CK DQ hold skew factor DQ/DQS output hold time from DQS Write command to DQS associated clock edges
-450 -400 0.48 0.48 3000 100 175 0.6 0.35 --
tCK.AVG tCK.AVG
ps ps ps
12)13)14) 13)14)15)
tCK.AVG tCK.AVG
ps ps ps ps ps ps ps nCK
9)16) 9)16) 9)16) 17) 18)
tAC.MIN 2 x tAC.MIN
-- Min(tCH.ABS, tCL.ABS) --
tAC.MAX tAC.MAX tAC.MAX
240 __ 340 -- + 0.25 -- -- -- -- 0.6 -- -- -- 1.1 0.6 70000
tQHS tQH
WL
19) 20)
tHP - tQHS
RL-1 - 0.25 0.35 0.35 0.2 0.2 0.4 0.35 200 275 0.9 0.4 45
DQS latching rising transition to associated clock tDQSS edges DQS input high pulse width DQS input low pulse width DQS falling edge to CK setup time DQS falling edge hold time from CK Write postamble Write preamble Address and control input setup time Address and control input hold time Read preamble Read postamble Active to precharge command
tCK.AVG tCK.AVG tCK.AVG tCK.AVG tCK.AVG tCK.AVG tCK.AVG
ps ps
21)
tDQSH tDQSL tDSS tDSH tWPST tWPRE tLS.BASE tLH.BASE tRPRE tRPST tRAS
21) 21)
22)23) 23)24) 25)26) 25)27) 28)
tCK.AVG tCK.AVG
ns
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
20
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Parameter
Symbol
DDR2-667 Min. Max. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2
Unit
Notes1)2)3)4)5)6)
7)8)
Active to active command period for 1KB page size products Active to active command period for 2KB page size products
tRRD tRRD
7.5 10 37.5 50 2 15 WR + tnRP 7.5 7.5
ns ns ns ns nCK ns nCK ns ns ns nCK nCK nCK nCK nCK nCK ns ns nCK
28)
28)
Four Activate Window for 1KB page size products tFAW Four Activate Window for 2KB page size products tFAW
28) 28)
tCCD Write recovery time tWR Auto-Precharge write recovery + precharge time tDAL Internal write to read command delay tWTR Internal Read to Precharge command delay tRTP Exit self-refresh to a non-read command tXSNR Exit self-refresh to read command tXSRD Exit precharge power-down to any valid tXP
CAS to CAS command delay command (other than NOP or Deselect) Exit power down to read command Exit active power-down mode to read command (slow exit, lower power) CKE minimum pulse width ( high and low pulse width) ODT turn-on delay ODT turn-on ODT turn-on (Power down mode) ODT turn-off delay ODT turn-off ODT turn-off (Power down mode) ODT to power down entry latency ODT to power down exit latency Mode register set command cycle time MRS command to ODT update delay OCD drive mode output delay Minimum time clocks remain ON after CKE asynchronously drops LOW
28) 29)30) 28)31) 28) 28)
tRFC +10
200 2 2 7 - AL 3 2
tXARD tXARDS tCKE tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD tMRD tMOD tOIT tDELAY
32)
tAC.MIN tAC.MIN + 2
2.5
tAC.MAX + 0.7 2 x tCK.AVG + tAC.MAX + 1
2.5
9)33)
tAC.MIN tAC.MIN + 2
3 8 2 0 0
tAC.MAX + 0.6 ns 2.5 x tCK.AVG + ns tAC.MAX + 1
-- -- 12 12 nCK nCK nCK ns ns ns
34)35)
1) 1)
tLS + tCK .AVG + -- tLH
1) For details and notes see the relevant Qimonda component data sheet 2) VDDQ = 1.8 V 0.1V; VDD = 1.8 V 0.1 V. See notes 5)6)7)8) 3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
21
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 7) The output timing reference voltage level is VTT. 8) New units, `tCK.AVG` and `nCK`, are introduced in DDR2-667 and DDR2-800. Unit `tCK.AVG` represents the actual tCK.AVG of the input clock under operation. Unit `nCK` represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2-400 and DDR2-533, `tCK` is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min). 9) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10PER).MIN = - 272 ps and tERR(6- 10PER).MAX = + 293 ps, then tDQSCK.MIN(DERATED) = tDQSCK.MIN - tERR(6-10PER).MAX = - 400 ps - 293 ps = - 693 ps and tDQSCK.MAX(DERATED) = tDQSCK.MAX - tERR(6-10PER).MIN = 400 ps + 272 ps = + 672 ps. Similarly, tLZ.DQ for DDR2-667 derates to tLZ.DQ.MIN(DERATED) = - 900 ps - 293 ps = - 1193 ps and tLZ.DQ.MAX(DERATED) = 450 ps + 272 ps = + 722 ps. (Caution on the MIN/MAX usage!) 10) Input clock jitter spec parameter. These parameters are referred to as 'input clock jitter spec parameters' and these parameters apply to DDR2-667 and DDR2-800 only. The jitter specified is a random jitter meeting a Gaussian distribution. 11) These parameters are specified per their average values, however it is understood that the relationship between the average timing and the absolute instantaneous timing holds all the times (min. and max of SPEC values are to be used for calculations). 12) Input waveform timing tDS with differential data strobe enabled MR[bit10] = 0, is referenced from the input signal crossing at the VIH.AC level to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL.AC level to the differential data strobe crosspoint for a falling signal applied to the device under test. DQS, DQS signals must be monotonic between Vil(DC)MAX and Vih(DC)MIN. See Figure 4. 13) If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can be executed. 14) These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective data strobe signal ((L/U/R)DQS / DQS) crossing. 15) Input waveform timing tDH with differential data strobe enabled MR[bit10] = 0, is referenced from the differential data strobe crosspoint to the input signal crossing at the VIH.DC level for a falling signal and from the differential data strobe crosspoint to the input signal crossing at the VIL.DC level for a rising signal applied to the device under test. DQS, DQS signals must be monotonic between VIL.DC.MAX and VIH.DC.MIN. See Figure 4. 16) tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a specific voltage level which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ) . 17) tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output slew rate mismatch between DQS / DQS and associated DQ in any given cycle. 18) tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for tQH calculation is determined by the following equation; tHP = MIN (tCH.ABS, tCL.ABS), where, tCH.ABS is the minimum of the actual instantaneous clock high time; tCL.ABS is the minimum of the actual instantaneous clock low time. 19) tQHS accounts for: 1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is transferred to the output; and 2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition, both of which are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation of the output drivers. 20) tQH = tHP - tQHS, where: tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification value under the max column. {The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.} Examples: 1) If the system provides tHP of 1315 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 975 ps minimum. 2) If the system provides tHP of 1420 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 1080 ps minimum. 21) These parameters are measured from a data strobe signal ((L/U/R)DQS / DQS) crossing to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. 22) Input waveform timing is referenced from the input signal crossing at the VIH.AC level for a rising signal and VIL.AC for a falling signal applied to the device under test. See Figure 5. 23) These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not. 24) Input waveform timing is referenced from the input signal crossing at the VIL.DC level for a rising signal and VIH.DC for a falling signal applied to the device under test. See Figure 5. 25) tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). Figure 3 shows a method to calculate these points when the device is no longer driving (tRPST), or begins driving (tRPRE) by measuring the signal at two different voltages. The actual voltage measurement points are not critical as long as the calculation is consistent.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
22
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
26) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.PER of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tJIT.PER.MIN = - 72 ps and tJIT.PER.MAX = + 93 ps, then tRPRE.MIN(DERATED) = tRPRE.MIN + tJIT.PER.MIN = 0.9 x tCK.AVG - 72 ps = + 2178 ps and tRPRE.MAX(DERATED) = tRPRE.MAX + tJIT.PER.MAX = 1.1 x tCK.AVG + 93 ps = + 2843 ps. (Caution on the MIN/MAX usage!). 27) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.DUTY of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tJIT.DUTY.MIN = - 72 ps and tJIT.DUTY.MAX = + 93 ps, then tRPST.MIN(DERATED) = tRPST.MIN + tJIT.DUTY.MIN = 0.4 x tCK.AVG - 72 ps = + 928 ps and tRPST.MAX(DERATED) = tRPST.MAX + tJIT.DUTY.MAX = 0.6 x tCK.AVG + 93 ps = + 1592 ps. (Caution on the MIN/MAX usage!). 28) For these parameters, the DDR2 SDRAM device is characterized and verified to support tnPARAM = RU{tPARAM / tCK.AVG}, which is in clock cycles, assuming all input clock jitter specifications are satisfied. For example, the device will support tnRP = RU{tRP / tCK.AVG}, which is in clock cycles, if all input clock jitter specifications are met. This means: For DDR2-667 5-5-5, of which tRP = 15 ns, the device will support tnRP = RU{tRP / tCK.AVG} = 5, i.e. as long as the input clock jitter specifications are met, Precharge command at Tm and Active command at Tm + 5 is valid even if (Tm + 5 - Tm) is less than 15 ns due to input clock jitter. 29) DAL = WR + RU{tRP(ns) / tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For tRP, if the result of the division is not already an integer, round up to the next highest integer. tCK refers to the application clock period. Example: For DDR2-533 at tCK = 3.75 ns with tWR programmed to 4 clocks. tDAL = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks. 30) tDAL.nCK = WR [nCK] + tnRP.nCK = WR + RU{tRP [ps] / tCK.AVG[ps] }, where WR is the value programmed in the EMR. 31) tWTR is at lease two clocks (2 x tCK) independent of operation frequency. 32) tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during the time period of tIS + 2 x tCK + tIH. 33) ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND. 34) ODT turn off time min is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD. 35) When the device is operated with input clock jitter, this parameter needs to be derated by {-tJIT.DUTY.MAX - tERR(6-10PER).MAX} and {-tJIT.DUTY.MIN - tERR(6-10PER).MIN } of the actual input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10PER).MIN = - 272 ps, tERR(6- 10PER).MAX = + 293 ps, tJIT.DUTY.MIN = - 106 ps and tJIT.DUTY.MAX = + 94 ps, then tAOF.MIN(DERATED) = tAOF.MIN + {- tJIT.DUTY.MAX - tERR(6-10PER).MAX} = - 450 ps + {- 94 ps - 293 ps} = - 837 ps and tAOF.MAX(DERATED) = tAOF.MAX + {- tJIT.DUTY.MIN - tERR(6-10PER).MIN} = 1050 ps + {106 ps + 272 ps} = + 1428 ps. (Caution on the MIN/MAX usage!)
FIGURE 3
Method for calculating transitions and endpoint
VOH - x mV VOH - 2x mV tHZ tRPST end point VOL + 2x mV VOL + x mV T1 T2
VTT + 2x mV VTT + x mV tLZ tRPRE begin point VTT - x mV VTT - 2x mV T1 T2
tHZ,tRPST end point = 2*T1-T2
tLZ,tRPRE begin point = 2*T1-T2
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
23
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 4
Differential input waveform timing - tDS and tDS
DQS DQS
tDS
tDH
tDS
tDH VDDQ VIH(ac) min VIH(dc) min
VREF(dc)
VIL(dc) max VIL(ac) max VSS
FIGURE 5
Differential input waveform timing - tlS and tlH
CK CK
tIS
tIH
tIS
tIH VDDQ VIH(ac) min VIH(dc) min VREF(dc) VIL(dc) max VIL(ac) max VSS
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
24
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 18
Timing Parameter by Speed Grade - DDR2-533
Parameter Symbol DDR2-533 Min. DQ output access time from CK / CK CAS A to CAS B command period CK, CK high-level width CKE minimum high and low pulse width CK, CK low-level width Auto-Precharge write recovery + precharge time Minimum time clocks remain ON after CKE asynchronously drops LOW DQ and DM input hold time (differential data strobe) Max. +500 -- 0.55 -- 0.55 -- -- -- -- -- +450 -- 300 + 0.25 -- -- -- -- -- -- ps Unit Notes1)2)3)4)5)
6)7)
tAC tCCD tCH tCKE tCL tDAL tDELAY tDH(base)
-500 2 0.45 3 0.45 WR + tRP
tCK tCK tCK tCK tCK
ns ps ps
8)18)
tIS + tCK + tIH
225 -25 0.35 -450 0.35 -- - 0.25 100 -25 0.2 0.2 37.5 50 MIN. (tCL, tCH) -- 375 0.6 250 2 x tAC.MIN
9)
10)
DQ and DM input hold time (single ended data tDH1(base) strobe) DQ and DM input pulse width (each input) DQS output access time from CK / CK DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) Write command to 1st DQS latching transition DQ and DM input setup time (differential data strobe)
11)
tDIPW tDQSCK tDQSL,H tDQSQ tDQSS tDS(base)
tCK
ps
tCK
ps
11)
tCK
ps ps
11)
DQ and DM input setup time (single ended data tDS1(base) strobe) DQS falling edge hold time from CK (write cycle) Four Activate Window period Clock half period Data-out high-impedance time from CK / CK Address and control input hold time Address and control input pulse width (each input) Address and control input setup time DQ low-impedance time from CK / CK DQS low-impedance from CK / CK Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS
11)
tDSH
tCK tCK
ns ns ps ps
13) 12)
DQS falling edge to CK setup time (write cycle) tDSS
tFAW tHP tHZ tIH(base) tIPW tIS(base) tLZ(DQ) tLZ(DQS) tMRD tOIT tQH
tAC.MAX
-- -- --
13) 11)
tCK
ps ps ps
11) 14) 14)
tAC.MIN
2 0
tAC.MAX tAC.MAX
-- 12 --
tCK
ns
tHP -tQHS
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
25
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Parameter
Symbol
DDR2-533 Min. Max. 400 7.8 3.9 -- -- -- 1.1 0.60 -- -- -- -- 0.60 --
Unit
Notes1)2)3)4)5)
6)7)
Data hold skew factor Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Precharge-All (8 banks) command period Read preamble Read postamble Active bank A to Active bank B command period Internal Read to Precharge command delay Write preamble Write postamble Write recovery time for write without AutoPrecharge Write recovery time for write with AutoPrecharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit active power-down mode to Read command (slow exit, lower power) Exit precharge power-down to any valid command (other than NOP or Deselect) Exit Self-Refresh to non-Read command Exit Self-Refresh to Read command
tQHS tREFI tRFC tRP tRP tRPRE tRPST tRRD tRTP tWPRE tWPST tWR
WR
-- -- -- 105
ps s s ns ns ns
14)15) 16)18) 17)
tRP + 1tCK
15 + 1tCK 0.9 0.40 7.5 10 7.5 0.25 x tCK 0.40 15
tCK tCK
ns ns ns
14) 14) 14)18) 16)20)
tCK tCK
ns
19)
tWR/tCK
7.5 2 6 - AL 2 -- -- -- -- -- --
tCK
ns
20)
tWTR tXARD tXARDS tXP tXSNR tXSRD
21) 22)
tCK tCK tCK
ns
22)
tRFC +10
200
tCK
1) For details and notes see the relevant Qimonda component data sheet 2) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V. See notes 5)6)7)8) 3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS/ RDQS, input reference level is the crosspoint when in differential strobe mode. 6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 7) The output timing reference voltage level is VTT. 8) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MR. 9) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 10) For timing definition, refer to the Component data sheet. 11) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate mis-match between DQS / DQS and associated DQ in any given cycle. 12) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH).
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
26
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
13) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving (tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These parameters are verified by design and characterization, but not subject to production test. 14) The Auto-Refresh command interval has be reduced to 3.9 s when operating the DDR2 DRAM in a temperature range between 85 C and 95 C. 15) 0 C TCASE 85 C 16) 85 C < TCASE 95 C 17) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 18) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 4 "Ordering Information for RoHS Compliant Products" on Page 5. 19) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 20) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MRS. 21) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies 200 z. 22) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In "standard active powerdown mode" (MR, A12 = "0") a fast power-down exit timing tXARD can be used. In "low active power-down mode" (MR, A12 ="1") a slow power-down exit timing tXARDS has to be satisfied.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
27
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 19
Timing Parameter by Speed Grade - DDR2-400
Parameter Symbol DDR2-400 Min. DQ output access time from CK / CK CAS A to CAS B command period CK, CK high-level width CKE minimum high and low pulse width CK, CK low-level width Auto-Precharge write recovery + precharge time Minimum time clocks remain ON after CKE asynchronously drops LOW DQ and DM input hold time (differential data strobe) Max. +600 -- 0.55 -- 0.55 -- -- -- -- -- +500 -- 350 + 0.25 -- -- -- -- -- -- ps Unit Notes1)2)3)4)5)
6)7)
tAC tCCD tCH tCKE tCL tDAL tDELAY tDH(base)
-600 2 0.45 3 0.45 WR + tRP
tCK tCK tCK tCK tCK
ns ps ps
8)22)
tIS + tCK + tIH
275 -25 0.35 -500 0.35 -- - 0.25 150 -25 0.2 0.2 37.5 50 MIN. (tCL, tCH) -- 475 0.6 350 2 x tAC.MIN
9)
10)
DQ and DM input hold time (single ended data tDH1(base) strobe) DQ and DM input pulse width (each input) DQS output access time from CK / CK DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) DQ and DM input setup time (differential data strobe) DQ and DM input setup time (single ended data strobe) DQS falling edge hold time from CK (write cycle) Four Activate Window period Clock half period Data-out high-impedance time from CK / CK Address and control input hold time Address and control input pulse width (each input) Address and control input setup time DQ low-impedance time from CK / CK DQS low-impedance from CK / CK Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS
11)
tDIPW tDQSCK tDQSL,H tDQSQ
tCK
ps
tCK
ps
11)
Write command to 1st DQS latching transition tDQSS
tCK
ps ps
11)
tDS(base) tDS1(base) tDSH
11)
tCK tCK
ns ns ps ps
13) 12)
DQS falling edge to CK setup time (write cycle) tDSS
tFAW tHP tHZ tIH(base) tIPW tIS(base) tLZ(DQ) tLZ(DQS) tMRD tOIT tQH
tAC.MAX
-- -- --
13) 11)
tCK
ps ps ps
11) 14) 14)
tAC.MIN
2 0
tAC.MAX tAC.MAX
-- 12 --
tCK
ns
tHP -tQHS
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
28
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Parameter
Symbol
DDR2-400 Min. Max. 450 7.8 3.9 -- -- -- 1.1 0.60 -- -- -- -- 0.60 --
Unit
Notes1)2)3)4)5)
6)7)
Data hold skew factor Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Precharge-All (8 banks) command period Read preamble Read postamble Active bank A to Active bank B command period Internal Read to Precharge command delay Write preamble Write postamble Write recovery time for write without AutoPrecharge Write recovery time for write with AutoPrecharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit active power-down mode to Read command (slow exit, lower power) Exit precharge power-down to any valid command (other than NOP or Deselect) Exit Self-Refresh to non-Read command Exit Self-Refresh to Read command
tQHS tREFI
-- -- -- 105
ps s s ns ns ns
14)15) 16)18) 17)
tRP tRP tRPRE tRPST tRRD tRTP tWPRE tWPST tWR
WR
tRP + 1tCK
15 + 1tCK 0.9 0.40 7.5 10 7.5 0.25 x tCK 0.40 15
tCK tCK
ns ns ns
14) 14) 14)18) 16)20)
tCK tCK
ns
19)
tWR/tCK
10 2 6 - AL 2 -- -- -- -- -- --
tCK
ns
20)
tWTR tXARD tXARDS tXP tXSNR tXSRD
21) 22)
tCK tCK tCK
ns
22)
tRFC +10
200
tCK
1) For details and notes see the relevant Qimonda component data sheet 2) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V. See notes 5)6)7)8) 3) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 5) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS/ RDQS, input reference level is the crosspoint when in differential strobe mode. 6) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 7) The output timing reference voltage level is VTT. 8) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MR. 9) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 10) For timing definition, refer to the Component data sheet. 11) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate mis-match between DQS / DQS and associated DQ in any given cycle. 12) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH).
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
29
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
13) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving (tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These parameters are verified by design and characterization, but not subject to production test. 14) The Auto-Refresh command interval has be reduced to 3.9 s when operating the DDR2 DRAM in a temperature range between 85 C and 95 C. 15) 0 C TCASE 85 C 16) 85 C < TCASE 95 C 17) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 18) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 4 "Ordering Information for RoHS Compliant Products" on Page 5. 19) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 20) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MRS. 21) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies 200 z. 22) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In "standard active powerdown mode" (MR, A12 = "0") a fast power-down exit timing tXARD can be used. In "low active power-down mode" (MR, A12 ="1") a slow power-down exit timing tXARDS has to be satisfied.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
30
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
3.3.3
ODT AC Electrical Characteristics
TABLE 20
ODT AC Characteristics and Operating Conditions for DDR2-667
This chapter contains the ODT AC electrical characteristics tables.
Symbol
Parameter / Condition
Values Min. Max. 2
Unit
Note
tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD
ODT turn-on delay ODT turn-on ODT turn-on (Power-Down Modes) ODT turn-off delay ODT turn-off ODT turn-off (Power-Down Modes) ODT to Power Down Mode Entry Latency ODT Power Down Exit Latency
2
tCK
ns ns
1)
tAC.MIN tAC.MIN + 2 ns
2.5
tAC.MAX + 0.7 ns 2 tCK + tAC.MAX + 1 ns
2.5
tCK
ns ns
2)
tAC.MIN tAC.MIN + 2 ns
3 8
tAC.MAX + 0.6 ns 2.5 tCK + tAC.MAX + 1 ns
-- --
tCK tCK
1) ODT turn on time min. is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measure from tAOND. 2) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
TABLE 21
ODT AC Characteristics and Operating Conditions for DDR2-533/DDR2-400
Symbol Parameter / Condition Values Min. Max. 2 Unit Note
tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD
ODT turn-on delay ODT turn-on ODT turn-on (Power-Down Modes) ODT turn-off delay ODT turn-off ODT turn-off (Power-Down Modes) ODT to Power Down Mode Entry Latency ODT Power Down Exit Latency
2
tCK
ns ns
1)
tAC.MIN tAC.MIN + 2 ns
2.5
tAC.MAX + 1 ns 2 tCK + tAC.MAX + 1 ns
2.5
tCK
ns ns
2)
tAC.MIN tAC.MIN + 2 ns
3 8
tAC.MAX + 0.6 ns 2.5 tCK + tAC.MAX + 1 ns
-- --
tCK tCK
1) ODT turn on time min. is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measure from tAOND. 2) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
31
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
3.4
Currents Specifications and Conditions
Chapter contains current tables for each of the product types and the definitions of the various currents. * Table 22 "IDD Measurement Conditions" on Page 32 * Table 23 "Definitions for IDD" on Page 33 * Table 24 "IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-3-A" on Page 34 * Table 25 "IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-3S-A" on Page 35 * Table 26 "IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-3.7-A" on Page 36
TABLE 22
IDD Measurement Conditions
Parameter Symbol Note
1)2)3)4)5)
Operating Current 0 IDD0 One bank Active - Precharge; tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING. Operating Current 1 One bank Active - Read - Precharge; IOUT = 0 mA, BL = 4, tCK = tCK.MIN, tRC = tRC.MIN, tRAS = tRAS.MIN, tRCD = tRCD.MIN, AL = 0, CL = CLMIN; CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are SWITCHING, Databus inputs are SWITCHING.
IDD1
6)
Precharge Standby Current IDD2N All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are SWITCHING, Databus inputs are SWITCHING. Precharge Power-Down Current Other control and address inputs are STABLE, Data bus inputs are FLOATING. Precharge Quiet Standby Current All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK.MIN; Other control and address inputs are STABLE, Data bus inputs are FLOATING. Active Standby Current Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX, tRP = tRP.MIN; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; IOUT = 0 mA.
IDD2P IDD2Q
IDD3N
Active Power-Down Current IDD3P(0) All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs are FLOATING. MRS A12 bit is set to LOW (Fast Power-down Exit); Active Power-Down Current IDD3P(1) All banks open; tCK = tCK.MIN, CKE is LOW; Other control and address inputs are STABLE, Data bus inputs are FLOATING. MRS A12 bit is set to HIGH (Slow Power-down Exit); Operating Current - Burst Read IDD4R All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CLMIN; tCK = tCKMIN; tRAS = tRASMAX; tRP = tRPMIN; CKE is HIGH, CS is HIGH between valid commands; Address inputs are SWITCHING; Data bus inputs are SWITCHING; IOUT = 0mA. Operating Current - Burst Write All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CLMIN; tCK = tCK.MIN; tRAS = tRAS.MAX., tRP = tRP.MAX; CKE is HIGH, CS is HIGH between valid commands. Address inputs are SWITCHING; Data Bus inputs are SWITCHING; Burst Refresh Current tCK = tCK.MIN., Refresh command every tRFC = tRFC.MIN interval, CKE is HIGH, CS is HIGH between valid commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING.
6)
IDD4W
IDD5B
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
32
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Parameter Distributed Refresh Current tCK = tCK.MIN., Refresh command every tRFC = tREFI interval, CKE is LOW and CS is HIGH between valid commands, Other control and address inputs are SWITCHING, Data bus inputs are SWITCHING.
Symbol Note
1)2)3)4)5)
IDD5D
Self-Refresh Current IDD6 CKE 0.2 V; external clock off, CK and CK at 0 V; Other control and address inputs are FLOATING, Data bus inputs are FLOATING. IDD6 current values are guaranteed up to TCASE of 85 C max.
6) All Bank Interleave Read Current IDD7 All banks are being interleaved at minimum tRC without violating tRRD using a burst length of 4. Control and address bus inputs are STABLE during DESELECTS. Iout = 0 mA. 1) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V 2) IDD specifications are tested after the device is properly initialized and IDD parameter are specified with ODT disabled. 3) Definitions for IDD see Table 23 4) For two rank modules: All active current measurements in the same IDD current mode. The other rank is in IDD2P Precharge Power-Down
Mode 5) For details and notes see the relevant Qimonda component data sheet 6) IDD1, IDD4R and IDD7 current measurements are defined with the outputs disabled (IOUT = 0 mA). To achieve this on module level the output buffers can be disabled using an EMRS(1) (Extended Mode Register Command) by setting A12 bit to HIGH.
TABLE 23
Definitions for IDD
Parameter LOW STABLE FLOATING SWITCHING Description
VIN VIL(ac).MAX, HIGH is defined as VIN VIH(ac).MIN
Inputs are stable at a HIGH or LOW level Inputs are VREF = VDDQ /2 Inputs are changing between HIGH and LOW every other clock (once per 2 cycles) for address and control signals, and inputs changing between HIGH and LOW every other data transfer (once per cycle) for DQ signals not including mask or strobes
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
33
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 24
IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-3-A
HYS64T128020HU-3-A HYS64T32000HU-3-A HYS64T64000HU-3-A HYS72T64000HU-3-A Product Type HYS72T128020HU-3-A Unit Note1)
Organization
256MB 1 Rank x64 -3
512MB 1 Rank x64 -3 Max. 600 720 400 40 320 400 150 50 1040 1120 1120 50 40 1240
512MB 1 Rank x72 -3 Max. 680 810 450 50 360 450 170 50 1170 1260 1260 50 45
1GB 2 Ranks x64 -3 Max. 640 760 800 80 640 800 300 100 1080 1160 1160 100 80
1GB 2 Ranks x72 -3 Max. 720 860 900 90 720 900 340 110 1220 1310 1310 110 90 mA mA mA mA mA mA mA mA mA mA mA mA mA
2) 2) 3) 3) 3) 3) 3) 3) 2) 2) 2) 3) 3) 2)
Symbol
Max. 380 440 200 20 160 200 80 20 600 680 560 20 20 960
1400 1280 1440 mA 1) Calculated values from component data. ODT disabled. IDD1, IDD4R, and IDD7, are defined with the outputs disabled. 2) The other rank is in IDD2P Precharge Power-Down mode 3) Both ranks are in the same IDDcurrent mode
IDD0 IDD1 IDD2N IDD2P IDD2Q IDD3N IDD3P( MRS = 0) IDD3P( MRS = 1) IDD4R IDD4W IDD5B IDD5D IDD6 IDD7
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
34
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 25
IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-3S-A
HYS64T128020HU-3S-A HYS64T128920HU-3S-A HYS64T32000HU-3S-A HYS64T32900HU-3S-A HYS64T64000HU-3S-A HYS64T64900HU-3S-A HYS72T64000HU-3S-A Product Type HYS72T128020HU-3S-A Unit Note1)
Organization
256MB 1 Rank x64 -3S
512MB 1 Rank x64 -3S Max. 570 680 400 40 320 400 150 50 1040 1120 1120 50 40 1180
512MB 1 Rank x72 -3S Max. 640 770 450 50 360 450 170 50 1170 1260 1260 50 45
1GB 2 Ranks x64 -3S Max. 610 720 800 80 640 800 300 100 1080 1160 1160 100 80
1GB 2 Ranks x72 -3S Max. 680 810 900 90 720 900 340 110 1220 1310 1310 110 90 mA mA mA mA mA mA mA mA mA mA mA mA mA
2) 2) 3) 3) 3) 3) 3) 3) 2) 2) 2) 3) 3) 2)
Symbol
Max. 360 420 200 20 160 200 80 20 600 680 560 20 20 910
1320 1220 1370 mA 1) Calculated values from component data. ODT disabled. IDD1, IDD4R, and IDD7, are defined with the outputs disabled. 2) The other rank is in IDD2P Precharge Power-Down mode 3) Both ranks are in the same IDDcurrent mode
IDD0 IDD1 IDD2N IDD2P IDD2Q IDD3N IDD3P( MRS = 0) IDD3P( MRS = 1) IDD4R IDD4W IDD5B IDD5D IDD6 IDD7
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
35
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 26
IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-3.7-A
HYS64T128020HU-3.7-A HYS64T128920HU-3.7-A HYS72T128020HU-3.7-A HYS64T32000HU-3.7-A HYS64T32900HU-3.7-A HYS64T64000HU-3.7-A HYS64T64900HU-3.7-A HYS72T64000HU-3.7-A Product Type Unit Note1)
Organization
256MB 1 Rank x64 -3.7
512MB 1 Rank x64 -3.7 Max. 520 600 320 30 240 320 130 40 720 760 1040 50 32 1120
512MB 1 Rank x72 -3.7 Max. 590 680 360 40 270 360 140 50 810 860 1170 50 36
1GB 2 Ranks x64 -3.7 Max. 550 630 640 60 480 640 260 80 750 790 1070 100 64
1GB 2 Ranks x72 -3.7 Max. 620 710 720 70 540 720 290 90 850 890 1210 110 72 mA mA mA mA mA mA mA mA mA mA mA mA mA
2) 2) 3) 3) 3) 3) 3) 3) 2) 2) 2) 3) 3) 2)
Symbol
Max. 320 360 160 20 120 160 60 20 400 440 520 20 16 880
1260 1160 1300 mA 1) Calculated values from component data. ODT disabled. IDD1, IDD4R, and IDD7, are defined with the outputs disabled. 2) The other rank is in IDD2P Precharge Power-Down mode 3) Both ranks are in the same IDDcurrent mode
IDD0 IDD1 IDD2N IDD2P IDD2Q IDD3N IDD3P( MRS = 0) IDD3P( MRS = 1) IDD4R IDD4W IDD5B IDD5D IDD6 IDD7
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
36
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 27
IDDSpecification for HYS[64/72]T[32/64/128]xxxHU-5-A
HYS64T128020HU-5-A HYS64T32000HU-5-A HYS64T64000HU-5-A HYS72T64000HU-5-A Product Type HYS72T128020HU-5-A Unit Note1)
Organization
256MB 1 Rank x64 -5
512MB 1 Rank x64 -5 Max. 440 480 260 30 200 280 100 40 560 600 960 50 32 1040
512MB 1 Rank x72 -5 Max. 500 540 290 40 230 320 120 50 630 680 1080 50 36
1GB 2 Ranks x64 -5 Max. 470 510 510 60 400 560 210 80 590 630 990 100 64
1GB 2 Ranks x72 -5 Max. 530 580 580 70 450 630 230 90 670 710 1120 110 72 mA mA mA mA mA mA mA mA mA mA mA mA mA
2) 2) 3) 3) 3) 3) 3) 3) 2) 2) 2) 3) 3) 2)
Symbol
Max. 280 300 130 20 100 140 50 20 340 360 480 20 16 840
1170 1070 1210 mA 1) Calculated values from component data. ODT disabled. IDD1, IDD4R, and IDD7, are defined with the outputs disabled. 2) The other rank is in IDD2P Precharge Power-Down mode 3) Both ranks are in the same IDDcurrent mode
IDD0 IDD1 IDD2N IDD2P IDD2Q IDD3N IDD3P( MRS = 0) IDD3P( MRS = 1) IDD4R IDD4W IDD5B IDD5D IDD6 IDD7
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
37
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
4
SPD Codes
This chapter lists all hexadecimal byte values stored in the EEPROM of the products described in this data sheet. SPD stands for serial presence detect. All values with XX in the table are module specific bytes which are defined during production. List of SPD Code Tables * * * * * * Table 28 "HYS[64/72]T[32/64/128]0x0HU-3-A" on Page 38 Table 29 "HYS[64/72]T[32/64]x00HU-3S-A" on Page 43 Table 30 "HYS[64/72]T128x20HU-3S-A" on Page 48 Table 31 "HYS[64/72]T[32/64]x00HU-3.7-A" on Page 52 Table 32 "HYS[64/72]T128x20HU-3.7-A" on Page 57 Table 33 "HYS[64/72]T[32/64/128]0x0HU-5-A" on Page 61
TABLE 28
HYS[64/72]T[32/64/128]0x0HU-3-A
HYS64T128020HU-3-A HYS64T32000HU-3-A HYS64T64000HU-3-A HYS72T64000HU-3-A Product Type HYS72T128020HU-3-A 1 GByte x72 2 Ranks (x8) PC2- 5300E- 444 Rev. 1.2 HEX 80 08 08 0E 0A 61 48 00 05
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 5300U- 444 Rev. 1.2 HEX 80 08 08 0E 0A 60 40 00 05
512MB x72 1 Rank (x8) PC2- 5300E- 444 Rev. 1.2 HEX 80 08 08 0E 0A 60 48 00 05
1 GByte x64 2 Ranks (x8) PC2- 5300U- 444 Rev. 1.2 HEX 80 08 08 0E 0A 61 40 00 05
Label Code
PC2- 5300U- 444 Rev. 1.2 HEX 80 08 08 0D 0A 60 40 00 05
JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 Description Programmed SPD Bytes in EEPROM Total number of Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
38
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3-A
HYS64T32000HU-3-A
HYS64T64000HU-3-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 5300U- 444 Rev. 1.2 HEX 30 45 00 82 08 00 00 0C 04 38 01 02 00 03 30 45 50 60 30 1E 30 2D 80 20
512MB x72 1 Rank (x8) PC2- 5300E- 444 Rev. 1.2 HEX 30 45 02 82 08 08 00 0C 04 38 01 02 00 03 30 45 50 60 30 1E 30 2D 80 20
HYS72T64000HU-3-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 5300U- 444 Rev. 1.2 HEX 30 45 00 82 08 00 00 0C 04 38 01 02 00 03 30 45 50 60 30 1E 30 2D 80 20
1 GByte x72 2 Ranks (x8) PC2- 5300E- 444 Rev. 1.2 HEX 30 45 02 82 08 08 00 0C 04 38 01 02 00 03 30 45 50 60 30 1E 30 2D 80 20
Label Code
PC2- 5300U- 444 Rev. 1.2 HEX 30 45 00 82 10 00 00 0C 04 38 01 02 00 03 30 45 50 60 30 28 30 2D 40 20
JEDEC SPD Revision Byte# 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description
tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes Component Attributes
tCK @ CLMAX -1 (Byte 18) [ns] tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns]
Module Density per Rank
tAS.MIN and tCS.MIN [ns]
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
39
HYS72T128020HU-3-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3-A
HYS64T32000HU-3-A
HYS64T64000HU-3-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 5300U- 444 Rev. 1.2 HEX 27 10 17 3C 1E 1E 00 00 39 69 80 18 22 00 53 78 4F 39 26 26 2B 1B 4A 20
512MB x72 1 Rank (x8) PC2- 5300E- 444 Rev. 1.2 HEX 27 10 17 3C 1E 1E 00 00 39 69 80 18 22 00 53 78 4F 39 26 26 2B 1B 4A 20
HYS72T64000HU-3-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 5300U- 444 Rev. 1.2 HEX 27 10 17 3C 1E 1E 00 00 39 69 80 18 22 00 53 78 4F 39 26 26 2B 1B 4A 20
1 GByte x72 2 Ranks (x8) PC2- 5300E- 444 Rev. 1.2 HEX 27 10 17 3C 1E 1E 00 00 39 69 80 18 22 00 53 78 4F 39 26 26 2B 1B 4A 20
Label Code
PC2- 5300U- 444 Rev. 1.2 HEX 27 10 17 3C 1E 1E 00 00 39 69 80 18 22 00 55 72 67 36 24 24 29 1A 52 1E
JEDEC SPD Revision Byte# 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Description
tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns]
Analysis Characteristics
tRC and tRFC Extension tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns]
PLL Relock Time
TCASE.MAX Delta / T4R4W Delta
Psi(T-A) DRAM T0 (DT0) T2N (DT2N, UDIMM) or T2Q (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W Sign (DT4R4W) T5B (DT5B)
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
40
HYS72T128020HU-3-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3-A
HYS64T32000HU-3-A
HYS64T64000HU-3-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 5300U- 444 Rev. 1.2 HEX 23 00 00 00 00 12 B0 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54 36 34 30 30 30
512MB x72 1 Rank (x8) PC2- 5300E- 444 Rev. 1.2 HEX 23 00 00 00 00 12 C2 7F 7F 7F 7F 7F 51 00 00 xx 37 32 54 36 34 30 30 30
HYS72T64000HU-3-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 5300U- 444 Rev. 1.2 HEX 23 00 00 00 00 12 B1 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54 31 32 38 30 32
1 GByte x72 2 Ranks (x8) PC2- 5300E- 444 Rev. 1.2 HEX 23 00 00 00 00 12 C3 7F 7F 7F 7F 7F 51 00 00 xx 37 32 54 31 32 38 30 32
Label Code
PC2- 5300U- 444 Rev. 1.2 HEX 34 00 00 00 00 12 A2 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54 33 32 30 30 30
JEDEC SPD Revision Byte# 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Description T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 Manufacturer's JEDEC ID Code (1) Manufacturer's JEDEC ID Code (2) Manufacturer's JEDEC ID Code (3) Manufacturer's JEDEC ID Code (4) Manufacturer's JEDEC ID Code (5) Manufacturer's JEDEC ID Code (6) Manufacturer's JEDEC ID Code (7) Manufacturer's JEDEC ID Code (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3 Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
41
HYS72T128020HU-3-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3-A
HYS64T32000HU-3-A
HYS64T64000HU-3-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 5300U- 444 Rev. 1.2 HEX 48 55 33 41 20 20 20 20 20 20 9x xx xx xx xx 00 FF
512MB x72 1 Rank (x8) PC2- 5300E- 444 Rev. 1.2 HEX 48 55 33 41 20 20 20 20 20 20 9x xx xx xx xx 00 FF
HYS72T64000HU-3-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 5300U- 444 Rev. 1.2 HEX 30 48 55 33 41 20 20 20 20 20 9x xx xx xx xx 00 FF
1 GByte x72 2 Ranks (x8) PC2- 5300E- 444 Rev. 1.2 HEX 30 48 55 33 41 20 20 20 20 20 9x xx xx xx xx 00 FF
Label Code
PC2- 5300U- 444 Rev. 1.2 HEX 48 55 33 41 20 20 20 20 20 20 7x xx xx xx xx 00 FF
JEDEC SPD Revision Byte# 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 - 98 128 255 Description Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year Module Manufacturing Date Week Module Serial Number Blank for customer use
99 - 127 Not used
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
42
HYS72T128020HU-3-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 29
HYS[64/72]T[32/64]x00HU-3S-A
HYS64T32000HU-3S-A HYS64T32900HU-3S-A HYS64T64000HU-3S-A HYS64T64900HU-3S-A Product Type HYS72T64000HU-3S-A 512MB x72 1 Rank (x8) PC2- 5300E- 555 Rev. 1.2 HEX 80 08 08 0E 0A 60 48 00 05 30 45 02 82 08 08 00 0C 04 38 01 02 00
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 5300U- 555 Rev. 1.2 HEX 80 08 08 0D 0A 60 40 00 05 30 45 00 82 10 00 00 0C 04 38 01 02 00
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 80 08 08 0E 0A 60 40 00 05 30 45 00 82 08 00 00 0C 04 38 01 02 00
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 80 08 08 0E 0A 60 40 00 05 30 45 00 82 08 00 00 0C 04 38 01 02 00
Label Code
PC2- 5300U- 555 Rev. 1.2 HEX 80 08 08 0D 0A 60 40 00 05 30 45 00 82 10 00 00 0C 04 38 01 02 00
JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Description Programmed SPD Bytes in EEPROM Total number of Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level
tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
43
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3S-A
HYS64T32900HU-3S-A
HYS64T64000HU-3S-A
HYS64T64900HU-3S-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 5300U- 555 Rev. 1.2 HEX 03 3D 50 50 60 3C 28 3C 2D 40 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 03 3D 50 50 60 3C 1E 3C 2D 80 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 03 3D 50 50 60 3C 1E 3C 2D 80 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22
512MB x72 1 Rank (x8) PC2- 5300E- 555 Rev. 1.2 HEX 03 3D 50 50 60 3C 1E 3C 2D 80 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22
Label Code
PC2- 5300U- 555 Rev. 1.2 HEX 03 3D 50 50 60 3C 28 3C 2D 40 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22
JEDEC SPD Revision Byte# 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Description Component Attributes
tCK @ CLMAX -1 (Byte 18) [ns] tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns]
Module Density per Rank
tAS.MIN and tCS.MIN [ns] tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns]
Analysis Characteristics
tRC and tRFC Extension tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns]
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
44
HYS72T64000HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3S-A
HYS64T32900HU-3S-A
HYS64T64000HU-3S-A
HYS64T64900HU-3S-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 5300U- 555 Rev. 1.2 HEX 00 55 72 5F 36 24 24 29 1A 52 1E 31 00 00 00 00 12 CA 7F 7F 7F 7F 7F 51
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 00 53 78 4B 39 26 26 2B 1B 4A 20 22 00 00 00 00 12 DE 7F 7F 7F 7F 7F 51
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 00 53 78 4B 39 26 26 2B 1B 4A 20 22 00 00 00 00 12 DE 7F 7F 7F 7F 7F 51
512MB x72 1 Rank (x8) PC2- 5300E- 555 Rev. 1.2 HEX 00 53 78 4B 39 26 26 2B 1B 4A 20 22 00 00 00 00 12 F0 7F 7F 7F 7F 7F 51
Label Code
PC2- 5300U- 555 Rev. 1.2 HEX 00 55 72 5F 36 24 24 29 1A 52 1E 31 00 00 00 00 12 CA 7F 7F 7F 7F 7F 51
JEDEC SPD Revision Byte# 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Description PLL Relock Time
TCASE.MAX Delta / T4R4W Delta
Psi(T-A) DRAM T0 (DT0) T2N (DT2N, UDIMM) or T2Q (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 Manufacturer's JEDEC ID Code (1) Manufacturer's JEDEC ID Code (2) Manufacturer's JEDEC ID Code (3) Manufacturer's JEDEC ID Code (4) Manufacturer's JEDEC ID Code (5) Manufacturer's JEDEC ID Code (6)
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
45
HYS72T64000HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3S-A
HYS64T32900HU-3S-A
HYS64T64000HU-3S-A
HYS64T64900HU-3S-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 5300U- 555 Rev. 1.2 HEX 00 00 xx 36 34 54 33 32 39 30 30 48 55 33 53 41 20 20 20 20 20 2x xx xx
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 00 00 xx 36 34 54 36 34 30 30 30 48 55 33 53 41 20 20 20 20 20 4x xx xx
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX 00 00 xx 36 34 54 36 34 39 30 30 48 55 33 53 41 20 20 20 20 20 2x xx xx
512MB x72 1 Rank (x8) PC2- 5300E- 555 Rev. 1.2 HEX 00 00 xx 37 32 54 36 34 30 30 30 48 55 33 53 41 20 20 20 20 20 4x xx xx
Label Code
PC2- 5300U- 555 Rev. 1.2 HEX 00 00 xx 36 34 54 33 32 30 30 30 48 55 33 53 41 20 20 20 20 20 4x xx xx
JEDEC SPD Revision Byte# 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 Description Manufacturer's JEDEC ID Code (7) Manufacturer's JEDEC ID Code (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3 Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
46
HYS72T64000HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3S-A
HYS64T32900HU-3S-A
HYS64T64000HU-3S-A
HYS64T64900HU-3S-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 5300U- 555 Rev. 1.2 HEX xx xx 00 FF
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX xx xx 00 FF
512MB x64 1 Rank (x8) PC2- 5300U- 555 Rev. 1.2 HEX xx xx 00 FF
512MB x72 1 Rank (x8) PC2- 5300E- 555 Rev. 1.2 HEX xx xx 00 FF
Label Code
PC2- 5300U- 555 Rev. 1.2 HEX xx xx 00 FF
JEDEC SPD Revision Byte# 94 95 - 98 128 255 Description Module Manufacturing Date Week Module Serial Number Blank for customer use
99 - 127 Not used
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
47
HYS72T64000HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 30
HYS[64/72]T128x20HU-3S-A
HYS64T128020HU-3S-A HYS64T128920HU-3S-A Product Type HYS72T128020HU-3S-A 1 GByte x72 2 Ranks (x8) PC2-5300E-555 Rev. 1.2 HEX 80 08 08 0E 0A 61 48 00 05 30 45 02 82 08 08 00 0C 04 38 01 02 00 03 3D
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-5300U-555 Rev. 1.2 HEX 80 08 08 0E 0A 61 40 00 05 30 45 00 82 08 00 00 0C 04 38 01 02 00 03 3D
Label Code JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Description Programmed SPD Bytes in EEPROM Total number of Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level
PC2-5300U-555 Rev. 1.2 HEX 80 08 08 0E 0A 61 40 00 05 30 45 00 82 08 00 00 0C 04 38 01 02 00 03 3D
tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes Component Attributes
tCK @ CLMAX -1 (Byte 18) [ns]
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
48
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3S-A
HYS64T128920HU-3S-A
Product Type
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-5300U-555 Rev. 1.2 HEX 50 50 60 3C 1E 3C 2D 80 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22 00 53 78 4B
1 GByte x72 2 Ranks (x8) PC2-5300E-555 Rev. 1.2 HEX 50 50 60 3C 1E 3C 2D 80 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22 00 53 78 4B
Label Code JEDEC SPD Revision Byte# 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Description
PC2-5300U-555 Rev. 1.2 HEX 50 50 60 3C 1E 3C 2D 80 20 27 10 17 3C 1E 1E 00 00 3C 69 80 18 22 00 53 78 4B
tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns]
Module Density per Rank
tAS.MIN and tCS.MIN [ns] tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns]
Analysis Characteristics
tRC and tRFC Extension tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns]
PLL Relock Time
TCASE.MAX Delta / T4R4W Delta
Psi(T-A) DRAM T0 (DT0)
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
49
HYS72T128020HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3S-A
HYS64T128920HU-3S-A
Product Type
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-5300U-555 Rev. 1.2 HEX 39 26 26 2B 1B 4A 20 22 00 00 00 00 12 DF 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54
1 GByte x72 2 Ranks (x8) PC2-5300E-555 Rev. 1.2 HEX 39 26 26 2B 1B 4A 20 22 00 00 00 00 12 F1 7F 7F 7F 7F 7F 51 00 00 xx 37 32 54
Label Code JEDEC SPD Revision Byte# 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Description T2N (DT2N, UDIMM) or T2Q (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 Manufacturer's JEDEC ID Code (1) Manufacturer's JEDEC ID Code (2) Manufacturer's JEDEC ID Code (3) Manufacturer's JEDEC ID Code (4) Manufacturer's JEDEC ID Code (5) Manufacturer's JEDEC ID Code (6) Manufacturer's JEDEC ID Code (7) Manufacturer's JEDEC ID Code (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3
PC2-5300U-555 Rev. 1.2 HEX 39 26 26 2B 1B 4A 20 22 00 00 00 00 12 DF 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
50
HYS72T128020HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3S-A
HYS64T128920HU-3S-A
Product Type
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-5300U-555 Rev. 1.2 HEX 31 32 38 39 32 30 48 55 33 53 41 20 20 20 20 2x xx xx xx xx 00 FF
1 GByte x72 2 Ranks (x8) PC2-5300E-555 Rev. 1.2 HEX 31 32 38 30 32 30 48 55 33 53 41 20 20 20 20 4x xx xx xx xx 00 FF
Label Code JEDEC SPD Revision Byte# 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 - 98 128 255 Description Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year Module Manufacturing Date Week Module Serial Number Blank for customer use
PC2-5300U-555 Rev. 1.2 HEX 31 32 38 30 32 30 48 55 33 53 41 20 20 20 20 4x xx xx xx xx 00 FF
99 - 127 Not used
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
51
HYS72T128020HU-3S-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 31
HYS[64/72]T[32/64]x00HU-3.7-A
HYS64T32000HU-3.7-A HYS64T32900HU-3.7-A HYS64T64000HU-3.7-A HYS64T64900HU-3.7-A Product Type HYS72T64000HU-3.7-A 512MB x72 1 Rank (x8) PC2- 4200E- 444 Rev. 1.1 HEX 80 08 08 0E 0A 60 48 00 05 3D 50 02 82 08 08 00 0C 04 38 00 02 00
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 4200U- 444 Rev. 1.2 HEX 80 08 08 0D 0A 60 40 00 05 3D 50 00 82 10 00 00 0C 04 38 00 02 00
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.1 HEX 80 08 08 0E 0A 60 40 00 05 3D 50 00 82 08 00 00 0C 04 38 00 02 00
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.2 HEX 80 08 08 0E 0A 60 40 00 05 3D 50 00 82 08 00 00 0C 04 38 00 02 00
Label Code
PC2- 4200U- 444 Rev. 1.1 HEX 80 08 08 0D 0A 60 40 00 05 3D 50 00 82 10 00 00 0C 04 38 00 02 00
JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Description Programmed SPD Bytes in EEPROM Total number of Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level
tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
52
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3.7-A
HYS64T32900HU-3.7-A
HYS64T64000HU-3.7-A
HYS64T64900HU-3.7-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 4200U- 444 Rev. 1.2 HEX 03 3D 50 50 60 3C 28 3C 2D 40 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.1 HEX 01 3D 50 50 60 3C 1E 3C 2D 80 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.2 HEX 03 3D 50 50 60 3C 1E 3C 2D 80 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28
512MB x72 1 Rank (x8) PC2- 4200E- 444 Rev. 1.1 HEX 01 3D 50 50 60 3C 1E 3C 2D 80 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28
Label Code
PC2- 4200U- 444 Rev. 1.1 HEX 01 3D 50 50 60 3C 28 3C 2D 40 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28
JEDEC SPD Revision Byte# 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Description Component Attributes
tCK @ CLMAX -1 (Byte 18) [ns] tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns]
Module Density per Rank
tAS.MIN and tCS.MIN [ns] tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns]
Analysis Characteristics
tRC and tRFC Extension tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns]
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
53
HYS72T64000HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3.7-A
HYS64T32900HU-3.7-A
HYS64T64000HU-3.7-A
HYS64T64900HU-3.7-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 4200U- 444 Rev. 1.2 HEX 00 53 72 53 2B 1D 1D 23 16 36 1C 30 00 00 00 00 12 BD 7F 7F 7F 7F 7F 51
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.1 HEX 00 51 78 3F 2E 1E 1E 24 17 34 1E 20 00 00 00 00 11 D0 7F 7F 7F 7F 7F 51
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.2 HEX 00 51 78 3F 2E 1E 1E 24 17 34 1E 20 00 00 00 00 12 D3 7F 7F 7F 7F 7F 51
512MB x72 1 Rank (x8) PC2- 4200E- 444 Rev. 1.1 HEX 00 51 78 3F 2E 1E 1E 24 17 34 1E 20 00 00 00 00 11 E2 7F 7F 7F 7F 7F 51
Label Code
PC2- 4200U- 444 Rev. 1.1 HEX 00 53 72 53 2B 1D 1D 23 16 36 1C 30 00 00 00 00 11 BA 7F 7F 7F 7F 7F 51
JEDEC SPD Revision Byte# 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Description PLL Relock Time
TCASE.MAX Delta / T4R4W Delta
Psi(T-A) DRAM T0 (DT0) T2N (DT2N, UDIMM) or T2Q (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 Manufacturer's JEDEC ID Code (1) Manufacturer's JEDEC ID Code (2) Manufacturer's JEDEC ID Code (3) Manufacturer's JEDEC ID Code (4) Manufacturer's JEDEC ID Code (5) Manufacturer's JEDEC ID Code (6)
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
54
HYS72T64000HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3.7-A
HYS64T32900HU-3.7-A
HYS64T64000HU-3.7-A
HYS64T64900HU-3.7-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 4200U- 444 Rev. 1.2 HEX 00 00 xx 36 34 54 33 32 39 30 30 48 55 33 2E 37 41 20 20 20 20 2x xx xx
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.1 HEX 00 00 xx 36 34 54 36 34 30 30 30 48 55 33 2E 37 41 20 20 20 20 5x xx xx
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.2 HEX 00 00 xx 36 34 54 36 34 39 30 30 48 55 33 2E 37 41 20 20 20 20 2x xx xx
512MB x72 1 Rank (x8) PC2- 4200E- 444 Rev. 1.1 HEX 00 00 xx 37 32 54 36 34 30 30 30 48 55 33 2E 37 41 20 20 20 20 5x xx xx
Label Code
PC2- 4200U- 444 Rev. 1.1 HEX 00 00 xx 36 34 54 33 32 30 30 30 48 55 33 2E 37 41 20 20 20 20 5x xx xx
JEDEC SPD Revision Byte# 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 Description Manufacturer's JEDEC ID Code (7) Manufacturer's JEDEC ID Code (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3 Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
55
HYS72T64000HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T32000HU-3.7-A
HYS64T32900HU-3.7-A
HYS64T64000HU-3.7-A
HYS64T64900HU-3.7-A
Product Type
Organization
256MB x64 1 Rank (x16)
256MB x64 1 Rank (x16) PC2- 4200U- 444 Rev. 1.2 HEX xx xx 00 FF
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.1 HEX xx xx 00 FF
512MB x64 1 Rank (x8) PC2- 4200U- 444 Rev. 1.2 HEX xx xx 00 FF
512MB x72 1 Rank (x8) PC2- 4200E- 444 Rev. 1.1 HEX xx xx 00 FF
Label Code
PC2- 4200U- 444 Rev. 1.1 HEX xx xx 00 FF
JEDEC SPD Revision Byte# 94 95 - 98 128 255 Description Module Manufacturing Date Week Module Serial Number Blank for customer use
99 - 127 Not used
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
56
HYS72T64000HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 32
HYS[64/72]T128x20HU-3.7-A
HYS64T128020HU-3.7-A HYS64T128920HU-3.7-A Product Type HYS72T128020HU-3.7-A 1 GByte x72 2 Ranks (x8) PC2-4200E-444 Rev. 1.1 HEX 80 08 08 0E 0A 61 48 00 05 3D 50 02 82 08 08 00 0C 04 38 00 02 00 01 3D
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-4200U-444 Rev. 1.2 HEX 80 08 08 0E 0A 61 40 00 05 3D 50 00 82 08 00 00 0C 04 38 00 02 00 03 3D
Label Code JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Description Programmed SPD Bytes in EEPROM Total number of Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level
PC2-4200U-444 Rev. 1.1 HEX 80 08 08 0E 0A 61 40 00 05 3D 50 00 82 08 00 00 0C 04 38 00 02 00 01 3D
tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes Component Attributes
tCK @ CLMAX -1 (Byte 18) [ns]
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
57
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3.7-A
HYS64T128920HU-3.7-A
Product Type
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-4200U-444 Rev. 1.2 HEX 50 50 60 3C 1E 3C 2D 80 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28 00 51 78 3F
1 GByte x72 2 Ranks (x8) PC2-4200E-444 Rev. 1.1 HEX 50 50 60 3C 1E 3C 2D 80 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28 00 51 78 3F
Label Code JEDEC SPD Revision Byte# 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Description
PC2-4200U-444 Rev. 1.1 HEX 50 50 60 3C 1E 3C 2D 80 25 37 10 22 3C 1E 1E 00 00 3C 69 80 1E 28 00 51 78 3F
tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns]
Module Density per Rank
tAS.MIN and tCS.MIN [ns] tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns]
Analysis Characteristics
tRC and tRFC Extension tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns]
PLL Relock Time
TCASE.MAX Delta / T4R4W Delta
Psi(T-A) DRAM T0 (DT0)
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
58
HYS72T128020HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3.7-A
HYS64T128920HU-3.7-A
Product Type
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-4200U-444 Rev. 1.2 HEX 2E 1E 1E 24 17 34 1E 20 00 00 00 00 12 D4 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54
1 GByte x72 2 Ranks (x8) PC2-4200E-444 Rev. 1.1 HEX 2E 1E 1E 24 17 34 1E 20 00 00 00 00 11 E3 7F 7F 7F 7F 7F 51 00 00 xx 37 32 54
Label Code JEDEC SPD Revision Byte# 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Description T2N (DT2N, UDIMM) or T2Q (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 Manufacturer's JEDEC ID Code (1) Manufacturer's JEDEC ID Code (2) Manufacturer's JEDEC ID Code (3) Manufacturer's JEDEC ID Code (4) Manufacturer's JEDEC ID Code (5) Manufacturer's JEDEC ID Code (6) Manufacturer's JEDEC ID Code (7) Manufacturer's JEDEC ID Code (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3
PC2-4200U-444 Rev. 1.1 HEX 2E 1E 1E 24 17 34 1E 20 00 00 00 00 11 D1 7F 7F 7F 7F 7F 51 00 00 xx 36 34 54
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
59
HYS72T128020HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-3.7-A
HYS64T128920HU-3.7-A
Product Type
Organization
1 GByte x64 2 Ranks (x8)
1 GByte x64 2 Ranks (x8) PC2-4200U-444 Rev. 1.2 HEX 31 32 38 39 32 30 48 55 33 2E 37 41 20 20 20 2x xx xx xx xx 00 FF
1 GByte x72 2 Ranks (x8) PC2-4200E-444 Rev. 1.1 HEX 31 32 38 30 32 30 48 55 33 2E 37 41 20 20 20 5x xx xx xx xx 00 FF
Label Code JEDEC SPD Revision Byte# 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 - 98 128 255 Description Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year Module Manufacturing Date Week Module Serial Number Blank for customer use
PC2-4200U-444 Rev. 1.1 HEX 31 32 38 30 32 30 48 55 33 2E 37 41 20 20 20 5x xx xx xx xx 00 FF
99 - 127 Not used
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
60
HYS72T128020HU-3.7-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
TABLE 33
HYS[64/72]T[32/64/128]0x0HU-5-A
HYS64T128020HU-5-A HYS64T32000HU-5-A HYS64T64000HU-5-A HYS72T64000HU-5-A Product Type HYS72T128020HU-5-A 1 GByte x72 2 Ranks (x8) PC2- 3200E- 333 Rev. 1.1 HEX 80 08 08 0E 0A 61 48 00 05 50 60 02 82 08 08 00 0C 04 38 00 02 00
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 3200U- 333 Rev. 1.1 HEX 80 08 08 0E 0A 60 40 00 05 50 60 00 82 08 00 00 0C 04 38 00 02 00
512MB x72 1 Rank (x8) PC2- 3200E- 333 Rev. 1.1 HEX 80 08 08 0E 0A 60 48 00 05 50 60 02 82 08 08 00 0C 04 38 00 02 00
1 GByte x64 2 Ranks (x8) PC2- 3200U- 333 Rev. 1.1 HEX 80 08 08 0E 0A 61 40 00 05 50 60 00 82 08 00 00 0C 04 38 00 02 00
Label Code
PC2- 3200U- 333 Rev. 1.1 HEX 80 08 08 0D 0A 60 40 00 05 50 60 00 82 10 00 00 0C 04 38 00 02 00
JEDEC SPD Revision Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Description Programmed SPD Bytes in EEPROM Total number of Bytes in EEPROM Memory Type (DDR2) Number of Row Addresses Number of Column Addresses DIMM Rank and Stacking Information Data Width Not used Interface Voltage Level
tCK @ CLMAX (Byte 18) [ns] tAC SDRAM @ CLMAX (Byte 18) [ns]
Error Correction Support (non-ECC, ECC) Refresh Rate and Type Primary SDRAM Width Error Checking SDRAM Width Not used Burst Length Supported Number of Banks on SDRAM Device Supported CAS Latencies DIMM Mechanical Characteristics DIMM Type Information DIMM Attributes
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
61
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-5-A
HYS64T32000HU-5-A
HYS64T64000HU-5-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 3200U- 333 Rev. 1.1 HEX 01 50 60 50 60 3C 1E 3C 28 80 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D
512MB x72 1 Rank (x8) PC2- 3200E- 333 Rev. 1.1 HEX 01 50 60 50 60 3C 1E 3C 28 80 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D
HYS72T64000HU-5-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 3200U- 333 Rev. 1.1 HEX 01 50 60 50 60 3C 1E 3C 28 80 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D
1 GByte x72 2 Ranks (x8) PC2- 3200E- 333 Rev. 1.1 HEX 01 50 60 50 60 3C 1E 3C 28 80 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D
Label Code
PC2- 3200U- 333 Rev. 1.1 HEX 01 50 60 50 60 3C 28 3C 28 40 35 47 15 27 3C 28 1E 00 00 37 69 80 23 2D
JEDEC SPD Revision Byte# 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Description Component Attributes
tCK @ CLMAX -1 (Byte 18) [ns] tAC SDRAM @ CLMAX -1 [ns] tCK @ CLMAX -2 (Byte 18) [ns] tAC SDRAM @ CLMAX -2 [ns] tRP.MIN [ns] tRRD.MIN [ns] tRCD.MIN [ns] tRAS.MIN [ns]
Module Density per Rank
tAS.MIN and tCS.MIN [ns] tAH.MIN and tCH.MIN [ns] tDS.MIN [ns] tDH.MIN [ns] tWR.MIN [ns] tWTR.MIN [ns] tRTP.MIN [ns]
Analysis Characteristics
tRC and tRFC Extension tRC.MIN [ns] tRFC.MIN [ns] tCK.MAX [ns] tDQSQ.MAX [ns] tQHS.MAX [ns]
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
62
HYS72T128020HU-5-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-5-A
HYS64T32000HU-5-A
HYS64T64000HU-5-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 3200U- 333 Rev. 1.1 HEX 00 51 78 33 24 1E 1B 1E 17 28 1B 1E 00 00 00 00 11 1A 7F 7F 7F 7F 7F 51
512MB x72 1 Rank (x8) PC2- 3200E- 333 Rev. 1.1 HEX 00 51 78 33 24 1E 1B 1E 17 28 1B 1E 00 00 00 00 11 2C 7F 7F 7F 7F 7F 51
HYS72T64000HU-5-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 3200U- 333 Rev. 1.1 HEX 00 51 78 33 24 1E 1B 1E 17 28 1B 1E 00 00 00 00 11 1B 7F 7F 7F 7F 7F 51
1 GByte x72 2 Ranks (x8) PC2- 3200E- 333 Rev. 1.1 HEX 00 51 78 33 24 1E 1B 1E 17 28 1B 1E 00 00 00 00 11 2D 7F 7F 7F 7F 7F 51
Label Code
PC2- 3200U- 333 Rev. 1.1 HEX 00 51 72 43 23 1D 19 1C 16 2E 1A 2D 00 00 00 00 11 02 7F 7F 7F 7F 7F 51
JEDEC SPD Revision Byte# 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Description PLL Relock Time
TCASE.MAX Delta / T4R4W Delta
Psi(T-A) DRAM T0 (DT0) T2N (DT2N, UDIMM) or T2Q (DT2Q, RDIMM) T2P (DT2P) T3N (DT3N) T3P.fast (DT3P fast) T3P.slow (DT3P slow) T4R (DT4R) / T4R4W Sign (DT4R4W) T5B (DT5B) T7 (DT7) Psi(ca) PLL Psi(ca) REG TPLL (DTPLL) TREG (DTREG) / Toggle Rate SPD Revision Checksum of Bytes 0-62 Manufacturer's JEDEC ID Code (1) Manufacturer's JEDEC ID Code (2) Manufacturer's JEDEC ID Code (3) Manufacturer's JEDEC ID Code (4) Manufacturer's JEDEC ID Code (5) Manufacturer's JEDEC ID Code (6)
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
63
HYS72T128020HU-5-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-5-A
HYS64T32000HU-5-A
HYS64T64000HU-5-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 3200U- 333 Rev. 1.1 HEX 00 00 xx 36 34 54 36 34 30 30 30 48 55 35 41 20 20 20 20 20 20 5x xx xx
512MB x72 1 Rank (x8) PC2- 3200E- 333 Rev. 1.1 HEX 00 00 xx 37 32 54 36 34 30 30 30 48 55 35 41 20 20 20 20 20 20 5x xx xx
HYS72T64000HU-5-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 3200U- 333 Rev. 1.1 HEX 00 00 xx 36 34 54 31 32 38 30 32 30 48 55 35 41 20 20 20 20 20 5x xx xx
1 GByte x72 2 Ranks (x8) PC2- 3200E- 333 Rev. 1.1 HEX 00 00 xx 37 32 54 31 32 38 30 32 30 48 55 35 41 20 20 20 20 20 5x xx xx
Label Code
PC2- 3200U- 333 Rev. 1.1 HEX 00 00 xx 36 34 54 33 32 30 30 30 48 55 35 41 20 20 20 20 20 20 5x xx xx
JEDEC SPD Revision Byte# 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 Description Manufacturer's JEDEC ID Code (7) Manufacturer's JEDEC ID Code (8) Module Manufacturer Location Product Type, Char 1 Product Type, Char 2 Product Type, Char 3 Product Type, Char 4 Product Type, Char 5 Product Type, Char 6 Product Type, Char 7 Product Type, Char 8 Product Type, Char 9 Product Type, Char 10 Product Type, Char 11 Product Type, Char 12 Product Type, Char 13 Product Type, Char 14 Product Type, Char 15 Product Type, Char 16 Product Type, Char 17 Product Type, Char 18 Module Revision Code Test Program Revision Code Module Manufacturing Date Year
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
64
HYS72T128020HU-5-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
HYS64T128020HU-5-A
HYS64T32000HU-5-A
HYS64T64000HU-5-A
Organization
256MB x64 1 Rank (x16)
512MB x64 1 Rank (x8) PC2- 3200U- 333 Rev. 1.1 HEX xx xx 00 FF
512MB x72 1 Rank (x8) PC2- 3200E- 333 Rev. 1.1 HEX xx xx 00 FF
HYS72T64000HU-5-A
Product Type
1 GByte x64 2 Ranks (x8) PC2- 3200U- 333 Rev. 1.1 HEX xx xx 00 FF
1 GByte x72 2 Ranks (x8) PC2- 3200E- 333 Rev. 1.1 HEX xx xx 00 FF
Label Code
PC2- 3200U- 333 Rev. 1.1 HEX xx xx 00 FF
JEDEC SPD Revision Byte# 94 95 - 98 128 255 Description Module Manufacturing Date Week Module Serial Number Blank for customer use
99 - 127 Not used
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
65
HYS72T128020HU-5-A
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
5
Package Outlines
FIGURE 6
Package Outline Raw Card A L-DIM-240-1
This chapter contains the package outlines of the products.
Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
66
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 7
Package Outline Raw Card B L-DIM-240-2
Notes 1. 2. 3. 4. The chip is only found on ECC modules. Drawing according to ISO 8015 Dimensions in mm General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
67
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 8
Package Outline Raw Card C L-DIM-240-3
Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
68
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 9
Package Outline L-DIM-240-8
Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
69
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 10
Package Outline L-DIM-240-9
Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
70
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 11
Package Outline Raw Card F L-DIM-240-6
Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
71
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
FIGURE 12
Package Outline Raw Card G L-DIM-240-7
Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
72
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
6
Product Type Nomenclature
Qimondas nomenclature uses simple coding combined with some propriatory coding. Table 34 provides examples for module and component product type number as well as the field number. The detailed field description together with possible values and coding explanation is listed for modules in Table 35 and for components in Table 36.
TABLE 34
Nomenclature Fields and Examples
Example for Field Number 1 Micro-DIMM DDR2 DRAM HYS HYB 2 64 18 3 T T 4 64/128 5 0 6 2 7 0 0 8 K A 9 M C 10 -5 -5 11 -A
512/1G 16
TABLE 35
DDR2 DIMM Nomenclature
Field 1 2 3 4 Description Qimonda Module Prefix Module Data Width [bit] DRAM Technology Memory Density per I/O [Mbit]; Module Density1) Values HYS 64 72 T 32 64 128 256 512 5 6 7 8 9 Raw Card Generation Number of Module Ranks Product Variations Package, Lead-Free Status Module Type 0 .. 9 0, 2, 4 0 .. 9 A .. Z D M R U F Coding Constant Non-ECC ECC DDR2 256 MByte 512 MByte 1 GByte 2 GByte 4 GByte Look up table 1, 2, 4 Look up table Look up table SO-DIMM Micro-DIMM Registered Unbuffered Fully Buffered
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
73
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Field 10
Description Speed Grade
Values -2.5F -2.5 -3 -3S -3.7 -5
Coding PC2-6400 5-5-5 PC2-6400 6-6-6 PC2-5300 4-4-4 PC2-5300 5-5-5 PC2-4200 4-4-4 PC2-3200 3-3-3 First Second
11
Die Revision
-A -B
1) Multiplying "Memory Density per I/O" with "Module Data Width" and dividing by 8 for Non-ECC and 9 for ECC modules gives the overall module memory density in MBytes as listed in column "Coding".
TABLE 36
DDR2 DRAM Nomenclature
Field 1 2 3 4 Description Qimonda Component Prefix Interface Voltage [V] DRAM Technology Component Density [Mbit] Values HYB 18 T 256 512 1G 2G 5+6 Number of I/Os 40 80 16 7 8 9 10 Product Variations Die Revision Package, Lead-Free Status Speed Grade 0 .. 9 A B C F -25F -2.5 -3 -3S -3.7 -5 Coding Constant SSTL_18 DDR2 256 Mbit 512 Mbit 1 Gbit 2 Gbit x4 x8 x16 Look up table First Second FBGA, lead-containing FBGA, lead-free DDR2-800 5-5-5 DDR2-800 6-6-6 DDR2-667 4-4-4 DDR2-667 5-5-5 DDR2-533 4-4-4 DDR2-400 3-3-3
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
74
Internet Data Sheet
HYS[64/72]T[32/64/128]xx0HU-[3/3S/3.7/5]-A Unbuffered DDR2 SDRAM Modules
Table of Contents
1 1.1 1.2 2 3 3.1 3.2 3.3 3.3.1 3.3.2 3.3.3 3.4 4 5 6 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Speed Grade Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODT AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Currents Specifications and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 16 17 18 18 20 31 32
SPD Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Product Type Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Rev. 1.41, 2007-05 03292006-EZUJ-JY4S
75
Internet Data Sheet
Edition 2007-05 Published by Qimonda AG Gustav-Heinemann-Ring 212 D-81739 Munchen, Germany (c) Qimonda AG 2007. All Rights Reserved. Legal Disclaimer The information given in this Internet Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office. Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Qimonda Office. Qimonda Components may only be used in life-support devices or systems with the express written approval of Qimonda, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. www.qimonda.com

▲Up To Search▲

Price & Availability of HYS64T64000HU-3S-A

	To Download HYS64T64000HU-3S-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .