 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DLM 600 Series 6 0 0 W A T T S P R O G R A M M A B L E D C S U P P LY LABORATORY Features * * * * * * * High power density High efficiency Remote voltage sense & remote operation Master/slave paralleling, active current sharing Low output noise CE mark, UL listing mark and C-UL listing mark Ethernet/LAN Interface Option Specifications INPUT Input voltage Frequency Current 90-132 / 180-264VAC,auto-ranging, 2 Wires + ground 47-63Hz 11A max. at 115VAC, 6A max. at 230VAC OPERATING Efficiency Parallel/Series operation 84% typical at maximum power 82% typical for DLM 5-7 and DLM 8-75 Up to 4 unit of the same model can be connected in parallel, with active current sharing control. Series operation, multiple units of same model can be connected in series, limited by 300Vpk between either output terminal and chassis The maximum allowed load line drop with remote sensing is 1V total for DLM 5-75 & DLM 8-75 model, 2V total for all other model Voltage , current (0-100%) and OVP (5-110%) of full scale can be programmed by selectable 0-5VDC, 0-10VDC, or 0-5K Voltage or current can be Monitored with userselectable ranges, scaled to 0-5VDC or 0-10VDC Two 3.5 digital LED displays indicate voltage, current and, over-voltage output set point, fault, external off, remote and output on LabVIEW(R) driver for M9G/M85 (Contact Powerbox) CE mark, UL listing mark and C-UL listing mark Enclosed 1RU 44(H) x 216 (W) x 432mm(D) 4.4Kg Input: IEC320 Output: Bus bar with 10-32 screws for 5-60VDC models; terminal blocks with 6-32 screws for 80-300V models OUTPUT Voltage adjustment Current adjustment Ripple & Noise Line regulation Load regulation Transient response Zero to rated output Zero to rated output See table Voltage: 0.005% of Vmax + 2mV Current: 0.01% of Imax + 2mA Voltage: 0.005% of Vmax + 2mV Current: 0.02% of Imax + 5mA 500 s to steady-state output voltage (within 0.1% of Vmax) for 50-100% or 100-50% load change +/-0.05% of maximum voltage or current over 8 hours after 30 minute warm-up time at fixed line, load and temperature 0.02%/C of maximum output voltage 0.03%/C of maximum output current Remote programming Remote sense Remote monitoring Displays and indicators Stability Software Regulatory compliance Temperature coefficient MECHANICAL Case ENVIRONMENTAL Operating temperature Storage temperature Cooling 0C to 50 -40C to 65C Internal variable speed fan with over-temperature protection. Dimensions Weight Connectors Your dependable power partner - www.powerbox.com.au 481 LABORATORY DLM 600 Series 6 0 0 W A T T S P R O G R A M M A B L E D C S U P P LY Selection Table MODEL NUMBER DLM 5-75 DLM 8-75 DLM10-60 DLM 20-30 DLM 40-15 DLM 60-10 DLM 80-7.5 DLM 150-4 DLM 300-2 OUTPUT RATING VOLTAGE (VDC) CURRENT (ADC) POWER (WATTS) LINE REGULATION VOLTAGE (0.01%OF VMAX +2MV) CURRENT (0.02%OF IMAX +2MA) LOAD REGULATION VOLTAGE (0.01%OF VMAX +2MV) CURRENT (0.05%OF IMAX +5MA) 0-5 0-8 0-10 0-20 0-40 0-60 0-80 0-150 0-300 0-75 0-75 0-60 0-30 0-15 0-10 0-7.5 0-4 0-2 375 600 600 600 600 600 600 600 600 2.4mV 2.4mV 2.5mV 3mV 4mV 5mV 6mV 9.5mV 17mV 9.5mA 9.5mA 8mA 5mA 3.5mA 3mA 2.8mA 2.2mA 2.1mA 2.4mV 2.4mV 2.5mV 3mV 4mV 5mV 6mV 9.5mV 17mV 20mA 20mA 17mA 11mA 8mA 7mA 6.5mA 5.8mA 5.4mA PROGRAMMING ACCURACY MODEL NUMBER ETHERNET (M130/M131) VOLTAGE (0.1% OF VMAX) CURRENT (0.25% OF IMAX) OVP (0.5% OF 1.1 X VMAX) VOLTAGE (0.2% OF VMAX) DISPLAY ACCURACY CURRENT (0.5% OF IMAX) OVP (1.0% OF 1.1 X VMAX) VOLTAGE (0.5% OF VMAX +1 CURRENT (1.0% OF IMAX +1 GPIB (M9G/M85) DLM 5-75 DLM 8-75 DLM10-60 DLM 20-30 DLM 40-15 DLM 60-10 DLM 80-7.5 DLM 150-4 DLM 300-2 8mV 8mV 10mV 20mV 40mV 60mV 80mV 150mV 300mV 188mA 188mA 150mA 75mA 38mA 25mA 19mA 10mA 5mA 44mV 44mV 55mV 110mV 220mV 330mV 440mV 825mV 1.65V 16mV 16mV 20mV 40mV 80mV 120mV 160mV 300mV 600mV 375mA 375mA 300mA 150mA 75mA 50mA 38mA 20mA 10mA 55mV 88mV 110mV 220mV 440mV 660mV 880mV 1.65V 3.3V 35mV 50mV 60mV 200mV 300mV 400mV 500mV 850mV 2.5V 850mA 850mA 700mA 400mA 160mA 110mA 85mA 50mA 30mA MODEL NUMBER RIPPLE AND NOISE, VOLTAGE MODE RIPPLE (RMS)* 5mV 5mV 5mV 2.5mV 2.5mV 2.5mV 4mV 7mV 10mV NOISE (P-P)* 30mV 30mV 30mV 15mV 15mV 20mV 20mV 40mV 60mV TEMPERATURE OVP STABILITY COEFFICIENT ADJUSTME CURRENT NTRANGE VOLTAGE CURRENT VOLTAGE (5% - 110% (0.05% OF (0.05% OF (0.02%/C (0.03%/C VMAX) IMAX) OF VMAX ) OF IMAX) OF VMAX) 0.25-.5.5V 0.4-8.8V 0.5-11V 1-22V 2-44V 3-66V 4-88V 7.5-165V 15-330V 2.5mV 4mV 5mV 10mV 20mV 30mV 40mV 75mV 150mV 37.5mA 37.5mA 30mA 15mA 7.5mA 5mA 3.75mA 2mA 1mA 1mV/C 1.6mV/C 2mV/C 4mV/C 8mV/C 12mV/C 16mV/C 30mV/C 60mV/C 22.5mA/C 22.5mA/C 18mA/C 9mA/C 4.5mA/C 3mA/C 2.25mA/C 1.2mA/C 0.6mA/C MAXIMUM TOTAL REMOTE SENSE DROP 1V 1V 2V 2V 2V 2V 2V 2V 2V DLM 5-75 DLM 8-75 DLM10-60 DLM 20-30 DLM 40-15 DLM 60-10 DLM 80-7.5 DLM 150-4 DLM 300-2 *RMS noise typical from 20Hz to 20MHz 482 LABORATORY DLM 600 Series 6 0 0 W A T T S P R O G R A M M A B L E D C S U P P LY REMOTE INTERFACE OPTIONS M9G IEEE-488.2 and RS 232 Interfaces Disconnect & Polarity reversal relays(10V to 300V models only, This option requires at least one of the following operations: M9G, M85, M130 or M131) Locking Shafts Optically Isolated Analog Programming and Monitoring Multi-channel Slave Interface Ethernet/LAN and RS232C Interfaces (16 bit) Multi-channel Slave Interface (16 bit)(M130 Master ONLY) PARALLEL CABLE DLMP1 Paralleling Cable; One cable per slave unit RACK-MOUNT KIT DLMRX Rack-mount Kit for single DLM with filter panel and for two units mounted side by side M6 M13 M51A M85 M130 M131 Technical Illustrations Your dependable power partner - www.powerbox.com.au 483 |
Price & Availability of DLM40-15
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |