|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
STA333BWQS 2.1-channel high-efficiency digital audio system with QSound QHD(R) Features ! ! Wide supply voltage range (4.5 to 20 V) 3 power output configurations - 2 channels of ternary PWM (stereo mode) (2 x 20 W @ 8 , 18 V). - 3 channels - left, right using binary and LFE using ternary PWM (2.1 mode) (2 x 9 W + 1 x 20 W @ 2 x 4 , 1 x 8 , 18 V) - 2 channels of ternary PWM (2 x 20 W) + stereo line out ternary 2.1 channels of 24-bit DDX(R) 100-dB SNR and dynamic range Selectable 32 kHz to 192 kHz input sample rates I2C control with selectable device address Digital gain/attenuation +48 dB to -80 dB in 0.5-dB steps Soft volume update Individual channel and master gain/attenuation Dual independent limiters/compressors Dynamic range compression or anti-clipping modes AutoModes - 15 preset crossover filters - 2 preset anti-clipping modes - Preset night-time listening mode Individual channel and master soft and hard mute Independent channel volume and DSP bypass Automatic zero-detect mute ! PowerSSO-36 slug down ! ! ! ! ! ! ! ! ! ! ! ! ! ! Automatic invalid input detect mute 2-channel I2S input data interface Input and output channel mapping 4 x 28-bit user programmable biquads (EQ) per channel Bass/treble tone control DC blocking selectable high-pass filter Selectable de-emphasis Sub channel mix into left and right channels Advanced AM interference frequency switching and noise-suppression modes Selectable high or low bandwidth noise-shaping topologies Variable max power correction for lower full-power THD Thermal overload and short-circuit protection Video application supports 576 x fs input mode QSound QHD(R) - Field proven stereo soundfield enhancement technology - Provides improved audio image width, seperation and depth for stereo signals - Synthesizes a 3-D stereo soundfield PowerSSO-36 slug down package ! ! ! ! ! ! ! ! ! ! ! ! ! Table 1. Device summary Order codes STA333BWQS STA333BWQS13TR Package PowerSSO-36 slug down PowerSSO-36 slug down Packaging Tube Tape and reel March 2008 Rev 1 1/71 www.st.com 1 Contents STA333BWQS Contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.1 QSound QHD(R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2 Connections and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.1 2.2 2.3 Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.1 3.2 3.3 3.4 3.5 3.6 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical specifications - digital section . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Electrical specifications - power section . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power-on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.6.1 Functional pin status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4 5 Processing data paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 I2C bus specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.1 Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.1.1 5.1.2 5.1.3 5.1.4 Data transition or change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Start condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Stop condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Data input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.2 5.3 Device addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Write operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.3.1 5.3.2 Byte write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Multi-byte write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.4 Read operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.4.1 5.4.2 5.4.3 Current address byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Current address multi-byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Random address byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 2/71 STA333BWQS 5.4.4 5.4.5 5.4.6 Contents Random address multi-byte read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Write mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Read mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6 Register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6.1 Configuration register A (0x00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 Master clock select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Interpolation ratio select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Thermal warning recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Thermal warning adjustment bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Fault detect recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.2 Configuration register B (0x01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 Serial audio input interface format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Serial data interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Serial data first bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Delay serial clock enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Channel input mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DDX(R) power output mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DDX(R) compensating pulse size register . . . . . . . . . . . . . . . . . . . . . . . . 31 Over-current warning detect adjustment bypass . . . . . . . . . . . . . . . . . . 32 6.3 Configuration register C (0x02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.3.1 6.3.2 6.3.3 6.4 Configuration register D (0x03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 6.4.1 6.4.2 6.4.3 6.4.4 6.4.5 6.4.6 6.4.7 6.4.8 High-pass filter bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 De-emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 DSP bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Post-scale link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Biquad coefficient link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Dynamic range compression/anti-clipping bit . . . . . . . . . . . . . . . . . . . . 33 Zero-detect mute enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 MiamiMode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6.5 Configuration register E (0x04) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6.5.1 6.5.2 6.5.3 6.5.4 6.5.5 6.5.6 Max power correction variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Max power correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Noise-shaper bandwidth selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 AM mode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 PWM speed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Distortion compensation variable enable . . . . . . . . . . . . . . . . . . . . . . . . 35 3/71 Contents 6.5.7 6.5.8 STA333BWQS Zero-crossing volume enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Soft volume update enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.6 Configuration register F (0x05) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6.6.1 6.6.2 6.6.3 6.6.4 6.6.5 6.6.6 6.6.7 Output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Invalid input detect mute enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Binary output mode clock loss detection . . . . . . . . . . . . . . . . . . . . . . . . 41 LRCK double trigger protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Auto EAPD on clock loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 IC power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 External amplifier power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 6.7 Volume control registers (0x06 to 0x0A) . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.7.1 6.7.2 6.7.3 6.7.4 6.7.5 Mute/line output configuration register . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Master volume register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Channel 1 volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Channel 2 volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Channel 3 / line output volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.8 Auto mode registers (0x0B and 0x0C) . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 6.8.1 6.8.2 6.8.3 6.8.4 AutoMode register 1 (0x0B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 AutoMode register 2 (0x0C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 AM interference frequency switching . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Bass management crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 6.9 Channel configuration registers ( 0x0E to 0x10) . . . . . . . . . . . . . . . . . . . 46 6.9.1 6.9.2 6.9.3 6.9.4 6.9.5 6.9.6 Tone control bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 EQ bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Volume bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Binary output enable registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Limiter select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Output mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.10 6.11 Tone control register (0x11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 6.10.1 Tone control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Dynamics control registers (0x12 to 0x15) . . . . . . . . . . . . . . . . . . . . . . . . 48 6.11.1 6.11.2 6.11.3 6.11.4 Limiter 1 attack/release rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Limiter 1 attack/release threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Limiter 2 attack/release rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Limiter 2 attack/release threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.12 User-defined coefficient control registers (0x16 to 0x26) . . . . . . . . . . . . . 52 4/71 STA333BWQS 6.12.1 6.12.2 6.12.3 6.12.4 6.12.5 6.12.6 6.12.7 6.12.8 6.12.9 Contents Coefficient address register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Coefficient b1 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Coefficient b1 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Coefficient b1 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Coefficient b2 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Coefficient b2 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Coefficient b2 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Coefficient a1 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Coefficient a1 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 6.12.10 Coefficient a1 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.11 Coefficient a2 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.12 Coefficient a2 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.13 Coefficient a2 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.14 Coefficient b0 data register bits 23:16 . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.15 Coefficient b0 data register bits 15:8 . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.16 Coefficient b0 data register bits 7:0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.12.17 Coefficient write/read control register . . . . . . . . . . . . . . . . . . . . . . . . . . 55 6.12.18 User-defined EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 6.12.19 Pre-scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.20 Post-scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.12.21 Over-current post-scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.13 6.14 6.15 6.16 Variable max power correction registers (0x27 to 0x28) . . . . . . . . . . . . . 59 Variable distortion compensation registers (0x29 to 0x2A) . . . . . . . . . . . 59 Fault detect recovery constant registers (0x2B to 0x2C) . . . . . . . . . . . . . 59 Device status register (0x2D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 7 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 7.1 7.2 7.3 Application scheme for power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . 61 PLL filter schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Typical output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 8 9 10 Characterization data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Package thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 5/71 Contents STA333BWQS 11 12 13 License information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Trademarks and other acknowledgements . . . . . . . . . . . . . . . . . . . . . . 69 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 6/71 STA333BWQS Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Table 47. Table 48. Table 49. Table 50. Table 51. Table 52. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Recommended operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical characteristics - digital section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Electrical characteristics - power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Functional pin status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Register summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Master clock select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Input sampling rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Interpolation ratio select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 IR bit settings as a function of input sample rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Thermal warning recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Thermal warning adjustment bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Fault detect recovery bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Serial audio input interface format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Serial data first bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Support serial audio input formats for MSB-first (SAIFB = 0) . . . . . . . . . . . . . . . . . . . . . . . 29 Supported serial audio input formats for LSB-first (SAIFB = 1) . . . . . . . . . . . . . . . . . . . . . 29 Delay serial clock enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Channel input mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DXX power output mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Output modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DXX compensating pulse size register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Compensating pulse size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Over-current warning detect adjustment bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 High-pass filter bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 De-emphasis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 DSP bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Post-scale link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Biquad coefficient link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Dynamic range compression/anti-clipping bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Zero-detect mute enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 MiamiMode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Max power correction variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Max power correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Noise-shaper bandwidth selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 AM mode enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 PWM speed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Distortion compensation variable enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Zero-crossing volume enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Soft volume update enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Output configuration engine selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Invalid input detect mute enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Binary output mode clock loss detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 LRCK double trigger protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Auto EAPD on clock loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 IC power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 External amplifier power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Line output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 7/71 STA333BWQS Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61. Table 62. Table 63. Table 64. Table 65. Table 66. Table 67. Table 68. Table 69. Table 70. Master volume offset as a function of MV[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Channel volume as a function of CxV[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 AutoMode gain compression/limiters selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 AM interference frequency switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 AutoMode AM switching frequency selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Base management crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Bass management crossover frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Channel limiter mapping as a function of CxLS bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Channel output mapping as a function of CxOM bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Tone control boost/cut as a function of BTC and TTC bits . . . . . . . . . . . . . . . . . . . . . . . . . 47 Limiter attack rate as a function of LxA bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Limiter release rate as a function of LxR bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Limiter attack threshold as a function of LxAT bits (AC-Mode). . . . . . . . . . . . . . . . . . . . . . 51 Limiter release threshold as a function of LxRT bits (AC-Mode). . . . . . . . . . . . . . . . . . . . . 51 Limiter attack threshold as a function of LxAT bits (DRC-Mode). . . . . . . . . . . . . . . . . . . . . 52 Limiter release threshold as a as a function of LxRT bits (DRC-Mode).. . . . . . . . . . . . . . . 52 RAM block for biquads, mixing, scaling, bass management. . . . . . . . . . . . . . . . . . . . . . . . 58 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 8/71 STA333BWQS Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Pin connection PowerSSO-36 (Top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Power-on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Test circuit 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Test circuit 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Processing data flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Write mode sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Read mode sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 OCFG = 00 (default value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 OCFG = 01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 OCFG = 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 OCFG = 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 STA333BWQS output mapping scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 2.0 channels (OCFG = 00) PWM slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 2.1 channels (OCFG = 01) PWM slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 2.1 channels (OCFG = 10) PWM slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Basic limiter and volume flow diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Application scheme for power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 PLL application scheme.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Output configuration for stereo BTL mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Output power (for 1% THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 FFT 0 dBfs (1 kHz, 12 V, 8 ohm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 FFT -60 dBfs (1 kHz, 12 V, 8 ohm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 THD vs. Freq (12 V Vcc 1 W output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 FFT 0 dBfs (1 kHz, 18 V, 8 ohm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 FFT -60 dBfs (1 kHz, 18 V, 8 ohm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 THD vs. Freq (18 V Vcc, 1 W output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Double layer PCB with 16 via holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 PowerSSO-36 power derating curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 PowerSSO-36 (slug-up) mechanical data and package dimensions . . . . . . . . . . . . . . . . . 67 9/71 Overview STA333BWQS 1 Overview The STA333BWQS is an integrated circuit comprising digital audio processing, digital amplifier control, DDX(R) power-output stage and Qsound QHD(R) to create a high-power single-chip DDX(R) solution with high-quality, high-efficiency and all digital amplification. The STA333BWQS is part of the SoundTerminalTM family that provides full digital audio streaming to the speaker, thereby offering cost effectiveness, low power dissipation and sound enrichment. The IC power section consists of four independent half-bridges. These can be configured via digital control to operate in different modes. 2.1 channels can be provided by two half-bridges and a single full-bridge, providing up to 2 x 9 W + 1 x 20 W of power output. Two channels can be provided by two full-bridges, providing up to 2 x 20 W of power. The IC can also be configured as a 2.1 channels with 2 x 20 W provided by the device and external power for DDX(R) power drive. Also provided in the STA333BWQS are a full assortment of digital processing features. This includes up to four programmable 28-bit biquads (EQ) per channel, and bass/treble tone control. AutomodesTM enable a time-to-market advantage by substantially reducing the amount of software development needed for certain functions. This includes Auto Volume loudness, preset volume curves and preset EQ settings. New advanced AM radio interference reduction modes. The serial audio data input interface accepts all possible formats, including the popular I2S format. Three channels of DDX(R) processing are provided. This high-quality conversion from PCM audio to DDX patented tri-state PWM switching waveform provides over 100 dB of SNR and dynamic range. 1.1 QSound QHD(R) Normally, reduced audio clarity is experienced due to the digital compression of music (and videosound) combined with various audio processing techniques used in broadcast transmission. This is most apparent in products such as digital televisions and audio players. These devices are faced with a multitude of audio challenges, primarily associated with the small speakers, that are limited in location and cabinet housing, plus economized speaker drivers and components. As such digital televisions and audio players are ideal candidates to benefit from stereo soundfield enhancement in order to deliver a full surround-like experience. QSound QHD(R) and its industry recognized QXpander(R) technology is a field-proven stereo soundfield enhancement technology that provides a broader stereo image width with greater separation and depth for stereo signals and synthesizes a 3-D stereo soundfield. QHD(R) removes the small centralized audio sweet spot by creating a very wide stereo image with full immersive audio. QHD(R) and its QXpander technology have been incorporated into hundreds of QSound and third party hardware and software products, with total shipments in the millions. 10/71 STA333BWQS Figure 1. Block diagram Overview I2 C I2 S interface Protection current/thermal Channel 1A Volume control Power control DDX Logic Channel 1B Channel 2A Regulators PLL Bias Channel 2B Digital (DSP) Power 11/71 Connections and pin description STA333BWQS 2 2.1 Connections and pin description Connection diagram Figure 2. Pin connection PowerSSO-36 (Top view) GND_SUB SA TEST_MODE VSS VCC_REG OUT2B GND2 VCC2 OUT2A OUT1B VCC1 GND1 OUT1A GND_REG VDD CONFIG OUT3B/DDX3B OUT3A/DDX3A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 VDD_DIG GND_DIG SCL SDA INT_LINE RESET SDI LRCKI BICKI XTI PLL_GND FILTER_PLL VDD_PLL PWRDN GND_DIG VDD_DIG TWARN/OUT4B EAPD/OUT4A D05AU1638 2.2 Pin description Table 2. Pin 1 2 3 4 5 6 7 8 9 10 Pin description Type GND I I I/O I/O O GND Power O O Name GND_SUB SA TEST_MODE VSS VCC_REG OUT2B GND2 VCC2 OUT2A OUT1B Substrate ground I2C select address This pin must be connected to ground Internal reference at Vcc-3.3 V Internal Vcc reference Output half bridge 2B Power negative supply Power positive supply Output half bridge 2A Output half bridge 1B Description 12/71 STA333BWQS Table 2. Pin 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Connections and pin description Pin description (continued) Type Power GND I/O GND Power I O O O I Power GND I Power I GND I I I I I O I/O I GND Power Name VCC1 GND1 OUT1A GND_REG VDD CONFIG OUT3B/DDX3B OUT3A/DDX3A EAPD/OUT4A TWARN/OUT4B VDD_DIG GND_DIG PWRDN VDD_PLL FILTER_PLL GND_PLL XTI BICKI LRCKI SDI RESET INT_LINE SDA SCL GND_DIG VDD_DIG Description Power positive supply Power negative supply Output half bridge 1A Internal ground reference Internal 3.3 V reference voltage Paralleled mode command PWM out CH3B, external bridge PWM out CH3A, external bridge Power down for external bridge Thermal warning from external bridge Digital supply voltage Digital groun Power down Positive supply for PLL Connection to PLL filter Negative supply for PLL PLL input clock I2S serial clock I2S left/right clock I2S serial data channels 1 and 2 Reset Fault interrupt: 0: fault detected in the power bridge, 1: normal operation) I2C serial data I2C serial clock Digital ground Digital supply voltage 13/71 Connections and pin description STA333BWQS 2.3 Thermal data Table 3. Thermal data Parameter Rth j-case Tth-sdj Tth-w Tth-sdh Rth j-amb Thermal resistance junction-case (thermal pad) Thermal shut-down junction temperature Thermal warning temperature Thermal shut-down hysteresis Thermal resistance junction-ambient (1) Min. Typ. Max. 1.5 Unit C/W C C C 150 130 20 1. See Section 9: Package thermal characteristics on page 66 for details. 14/71 STA333BWQS Electrical specifications 3 3.1 Electrical specifications Absolute maximum ratings Table 4. Symbol Vcc Absolute maximum ratings Parameter Power supply voltage (VCC1, VCC2) Min -0.3 -0.3 -0.3 0 -40 Typ Max 23 4 4 150 150 Unit V V V C C VDD_DIG Digital supply voltage VDD_PLL PLL supply voltage Top Tstg Operating junction temperature Storage temperature Note: Stresses beyond those listed under "Absolute maximum ratings" (Table 4) make cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended operating condition" are not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. In the real application, power supply with nominal value rated inside recommended operating conditions, may experience some rising beyond the maximum operating condition for short time when no or very low current is sinked (amplifier in mute state). In this case the reliability of the device is guaranteed, provided that the absolute maximum rating is not exceeded. 3.2 Recommended operating conditions Table 5. Symbol Vcc Recommended operating condition Parameter Power supply voltage (VCC1, VCC2) Min 4.5 2.7 2.7 0 3.3 3.3 Typ Max 20 3.6 3.6 70 Unit V V V C VDD_DIG Digital supply voltage VDD_PLL PLL supply voltage Tamb Ambient temperature 15/71 Electrical specifications STA333BWQS 3.3 Table 6. Symbol Iil Iih Vil Vih Vol Voh Ipu Rpu Electrical specifications - digital section Electrical characteristics - digital section Parameter Low level input current , no pull-up resistor High level input current, no pull-down resistor Low level input voltage High level input voltage Low level output voltage High level output voltage Pull-up current Equivalent pull-up resistance Iol = 2 mA Ioh = 2 mA 0.8 * VDD_DIG -25 66 50 125 0.8 * VDD_DIG 0.4 * VDD_DIG Conditions Vi=0 V Vi = VDD_DIG = 3.6 V Min -10 -10 Typ Max 10 10 0.2 * VDD_DIG Unit A A V V V V A k 3.4 Electrical specifications - power section The specifications given in this section are with the operating conditions VCC = 18 V, f = 1 kHz, fsw = 384 kHz, Tamb = 25 C, RL = 8 unless otherwise specified Table 7. Symbol Electrical characteristics - power section Parameter Output power BTL THD = 10% 20 THD = 1% THD = 10% 7 W 9 180 95 95 10 8 15 10 10 4.5 15 30 18 18 18 250 m % % A ns ns ns ns V Conditions THD = 1% Min Typ 16 W Max Unit Po Output power SE Power P-channel/N-channel MOSFET (total bridge) Power P-channel RdsON matching Power N-channel RdsON matching Power P-channel/N-channel leakage ldss Low-current dead time (static) High-current dead time (dynamic) Rise time Fall time Supply voltage operating voltage RL = 4 ld = 1.5 A ld = 1.5 A ld = 1.5 A VCC = 20 V Resistive load(1) Iload = 1.5 A(1) Resistive load(1) Resistive load(1) RdsON gP gN Idss ILDT IHDT tr tf Vcc 16/71 STA333BWQS Table 7. Symbol Electrical specifications Electrical characteristics - power section (continued) Parameter Conditions Min Typ 0.1 Max 1 Unit mA Supply current from Vcc in power PWRDN = 0 down IVCC Supply current from Vcc in operation Supply current DDX processing (reference only) Overcurrent limit Short circuit protection Under-voltage protection Output minimum pulse width Dynamic range Signal to noise ratio, ternary mode Signal to noise ratio binary mode PSSR Power supply rejection ratio DDX stereo mode, <5 kHz VRIPPLE = 1 V RMS Audio input = dither only DDX stereo mode Po = 1 W, f = 1 kHz DDX stereo mode, <5 kHz One channel driven at 1 W Other channel measured Po = 2 x 20 W, 8 Po = 2 x 9 W @ 4 , 1 x 20 W into 8 No load 20 PCM input signal = -60 dBFS, Switching frequency = 384 kHz No LC filters Internal clock = 49.152 MHz (2) 30 mA IVDD Ilim Isc UVL tmin DR 80 2.2 2.7 3.0 3.6 3.5 30 100 100 4.3 60 4.0 mA A A V ns dB dB dB dB Hi-Z output SNR A-Weighted 90 80 THD+N Total harmonic distortion + noise 0.2 % XTALK Crosstalk Peak efficiency, DDX mode 80 90 dB % 87 Peak efficiency,binary modes 1. Refer to Figure 4: Test circuit 1. 2. Limit current if the register (OCRB par 6.1.3.3) overcurrent warning detect adjustment bypass is enabled. When disabled refer to the Isc. 17/71 Electrical specifications STA333BWQS 3.5 Power-on sequence Figure 3. Power-on sequence VCC VDD_DIG XTI Reset I 2C PWDN Don't care TR TC Don't care CMD0 CMD1 CMD2 Referring to Figure 3 above: TR = mimimum time between XTI master clock stable and reset removal: 1 ms, TC = minimum time between reset removal and I2C program sequence start: 1 ms. Note: Note: Clock stable means: fmax - fmin < 1 MHz. VCC > VDD_DIG must be guaranteed at all times. 3.6 3.6.1 Testing Functional pin status Table 8. Pin name PWRDN PWRDN TWARN TWARN EAPD EAPD Functional pin status Number 23 23 20 20 19 19 Logic value 0 1 0 1 0 1 Low-power mode Normal operation Temperature warning from external power stage Normal operation Low-power operation for power stage. All internal regulators are switched off Normal operation IC status 18/71 STA333BWQS Figure 4. Test circuit 1 OUTxY Electrical specifications Vcc (3/4)Vcc Low-current dead time = MAX(DTr, DTf) (1/2)Vcc (1/4)Vcc +Vcc t Duty cycle = 50% M58 INxY M57 gnd OUTxY R8 + V67 vdc = Vcc/2 DTr DTf Figure 5. Test circuit 2 High Current Dead time for Bridge application = ABS(DTout(A)-DTin(A))+ABS(DTOUT(B)-DTin(B)) +VCC Duty cycle=A DTout(A) M58 Q1 OUTA Rload=4 L67 10 C69 470nF DTout(B) L68 10 C70 470nF Q2 OUTB M64 Duty cycle=B DTin(A) INA DTin(B) INB Iout=1.5A M57 Q3 Iout=1.5A Q4 M63 C71 470nF Duty cycle A and B: Fixed to have DC output current of 4A in the direction shown in figure D06AU1651 19/71 Processing data paths STA333BWQS 4 Processing data paths Here are some diagrams that represent the data processing paths inside STA333BWQS. The first 2-times oversampling FIR filter allows 2x fs audio processing. Then a selectable high-pass filter removes the DC level. Four biquad filters allow a full equalization system. A final crossover filter is present that can alternatively be used as a fifth biquad stage, see the I2C registers for this specific usage. A pre scaler and a final post scaler provide full control over the signal dynamics before and after the filtering stages, respectively. A mixer function is also available. Figure 6. Sampling frequency=Fs Processing data flow Sampling frequency=2xFs x2 FIR over sampling PreScale Hi-Pass Filter Biquad #1 Biquad #2 Biquad #3 Biquad #4 DeEmphasis Bass Treble L If HPB=0 If DEMP=0 From I2S input interface User-Defined Filters If C1TCB=0 BTC: Bass Boost/Cut TTC: Treble Boost/Cut If DSPB=0 and C1EQBP=0 x2 FIR over sampling PreScale Hi-Pass Filter Biquad #1 Biquad #2 Biquad #3 Biquad #4 DeEmphasis Bass Treble R If HPB=0 If DEMP=0 User-Defined Filters If C2TCB=0 BTC: Bass Boost/Cut TTC: Treble Boost/Cut If DSPB=0 and C2EQBP=0 L R C1Mx1 + C1Mx2 Hi-Pass XO Filter Vol And Limiter Post scale C2Mx1 + C2Mx2 Hi-Pass XO Filter Vol And Limiter Post scale C3Mx1 + C3Mx2 Lo-Pass XO Filter Vol And Limiter Post scale User-Defined Mix Coefficients Crossover Frequency determined by XO Setting User Defined If XO=0000 20/71 STA333BWQS I2C bus specification 5 I2C bus specification The STA333BWQS supports the I2C protocol via the input ports SCL and SDA_IN (master to slave) and the output port SDA_OUT (slave to master). This protocol defines any device that sends data on to the bus as a transmitter and any device that reads the data as a receiver. The device that controls the data transfer is known as the master and the other as the slave. The master always starts the transfer and provides the serial clock for synchronization. STA333BWQS is always a slave device in all of its communications. It supports up to 400 kb/s rate (fast-mode bit rate). STA333BWQS I2C is a slave only interface. 5.1 5.1.1 Communication protocol Data transition or change Data changes on the SDA line must only occur when the SCL clock is low. SDA transition while the clock is high is used to identify a START or STOP condition. 5.1.2 Start condition START is identified by a high to low transition of the data bus SDA signal while the clock signal SCL is stable in the high state. A START condition must precede any command for data transfer. 5.1.3 Stop condition STOP is identified by low to high transition of the data bus SDA signal while the clock signal SCL is stable in the high state. A STOP condition terminates communication between STA333BWQS and the bus master. 5.1.4 Data input During the data input the STA333BWQS samples the SDA signal on the rising edge of clock SCL. For correct device operation the SDA signal must be stable during the rising edge of the clock and the data can change only when the SCL line is low. 5.2 Device addressing To start communication between the master and the STA333BWQS, the master must initiate with a start condition. Following this, the master sends onto the SDA line 8-bits (MSB first) corresponding to the device select address and read or write mode. The seven most significant bits are the device address identifiers, corresponding to the I2C bus definition. In the STA333BWQS the I2C interface has two device addresses depending on the SA port configuration, 0x38 when SA = 0, and 0x3A when SA = 1. The eighth bit (LSB) identifies read or write operation RW, this bit is set to 1 in read mode and 0 for write mode. After a START condition the STA333BWQS identifies on the bus the device address and if a match is found, it acknowledges the identification on SDA bus during the 9th bit time. The byte following the device identification byte is the internal space address. 21/71 I2C bus specification STA333BWQS 5.3 Write operation Following the START condition the master sends a device select code with the RW bit set to 0. The STA333BWQS acknowledges this and the writes for the byte of internal address. After receiving the internal byte address the STA333BWQS again responds with an acknowledgement. 5.3.1 Byte write In the byte write mode the master sends one data byte, this is acknowledged by the STA333BWQS. The master then terminates the transfer by generating a STOP condition. 5.3.2 Multi-byte write The multi-byte write modes can start from any internal address. The master generating a STOP condition terminates the transfer. 5.4 5.4.1 Read operation Current address byte read Following the START condition the master sends a device select code with the RW bit set to 1. The STA333BWQS acknowledges this and then responds by sending one byte of data. The master then terminates the transfer by generating a STOP condition. 5.4.2 Current address multi-byte read The multi-byte read modes can start from any internal address. Sequential data bytes are read from sequential addresses within the STA333BWQS. The master acknowledges each data byte read and then generates a STOP condition terminating the transfer. 5.4.3 Random address byte read Following the START condition the master sends a device select code with the RW bit set to 0. The STA333BWQS acknowledges this and then the master writes the internal address byte. After receiving, the internal byte address the STA333BWQS again responds with an acknowledgement. The master then initiates another START condition and sends the device select code with the RW bit set to 1. The STA333BWQS acknowledges this and then responds by sending one byte of data. The master then terminates the transfer by generating a STOP condition. 5.4.4 Random address multi-byte read The multi-byte read modes could start from any internal address. Sequential data bytes are read from sequential addresses within the STA333BWQS. The master acknowledges each data byte read and then generates a STOP condition terminating the transfer. 22/71 STA333BWQS I2C bus specification 5.4.5 Figure 7. BYTE WRITE Write mode sequence Write mode sequence ACK DEV-ADDR START RW ACK ACK SUB-ADDR RW DATA IN ACK DATA IN STOP SUB-ADDR ACK DATA IN STOP ACK ACK MULTIBYTE WRITE START DEV-ADDR 5.4.6 Figure 8. CURRENT ADDRESS READ START Read mode sequence Read mode sequence ACK NO ACK DEV-ADDR RW ACK DATA STOP ACK SUB-ADDR DEV-ADDR ACK DATA NO ACK RANDOM ADDRESS READ START SEQUENTIAL CURRENT READ START DEV-ADDR RW RW= ACK HIGH DEV-ADDR DATA START ACK DATA RW ACK DATA NO ACK STOP STOP ACK ACK SUB-ADDR RW START DEV-ADDR RW ACK DATA ACK DATA ACK DATA STOP NO ACK SEQUENTIAL RANDOM READ START DEV-ADDR 23/71 Register description STA333BWQS 6 Table 9. Addr 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F Register description Register summary Name ConfA ConfB ConfC ConfD ConfE ConfF Mute/LOC Mvol C1Vol C2Vol C3Vol Auto1 Auto2 Auto3 C1Cfg C2Cfg C3Cfg Tone L1ar L1atrt L2ar L2atrt Cfaddr B1cf1 B1cf2 B1cf3 B2cf1 B2cf2 B2cf3 A1cf1 A1cf2 A1cf3 C1B23 C1B15 C1B7 C2B23 C2B15 C2B7 C3B23 C3B15 C3B7 C1B22 C1B14 C1B6 C2B22 C2B14 C2B6 C3B22 C3B14 C3B6 C1OM1 C2OM1 C3OM1 TTC3 L1A3 L1AT3 L2A3 L2AT3 C1OM0 C2OM0 C3OM0 TTC2 L1A2 L1AT2 L2A2 L2AT2 C1LS1 C2LS1 C3LS1 TTC1 L1A1 L1AT1 L2A1 L2AT1 CFA5 C1B21 C1B13 C1B5 C2B21 C2B13 C2B5 C3B21 C3B13 C3B5 C1LS0 C2LS0 C3LS0 TTC0 L1A0 L1AT0 L2A0 L2AT0 CFA4 C1B20 C1B12 C1B4 C2B20 C2B12 C2B4 C3B20 C3B12 C3B4 C1BO C2BO C3BO BTC3 L1R3 L1RT3 L2R3 L2RT3 CFA3 C1B19 C1B11 C1B3 C2B19 C2B11 C2B3 C3B19 C3B11 C3B3 C1VBP C2VBP C3VBP BTC2 L1R2 L1RT2 L2R2 L2RT2 CFA2 C1B18 C1B10 C1B2 C2B18 C2B10 C2B2 C3B18 C3B10 C3B2 BTC1 L1R1 L1RT1 L2R1 L2RT1 CFA1 C1B17 C1B9 C1B1 C2B17 C2B9 C2B1 C3B17 C3B9 C3B1 BTC0 L1R0 L1RT0 L2R0 L2RT0 CFA0 C1B16 C1B8 C1B0 C2B16 C2B8 C2B0 C3B16 C3B8 C3B0 C1EQBP C2EQBP C1TCB C2TCB XO3 XO2 D7 FDRB C2IM OCRB MME SVE EAPD LOC1 MV7 C1V7 C2V7 C3V7 ZDE ZCE PWDN LOC0 MV6 C1V6 C2V6 C3V6 MV5 C1V5 C2V5 C3V5 AMGC1 XO1 MV4 C1V4 C2V4 C3V4 AMGC0 XO0 AMAM2 AMAM1 AMAM0 AMAME D6 TWAB C1IM D5 TWRB DSCKE CSZ3 DRC DCCV ECLE D4 IR1 SAIFB CSZ2 BQL PWMS LDTE D3 IR0 SAI3 CSZ1 PSL AME BCLE C3M MV3 C1V3 C2V3 C3V3 D2 MCS2 SAI2 CSZ0 DSPB NSBW IDE C2M MV2 C1V2 C2V2 C3V2 D1 MCS1 SAI1 OM1 DEMP MPC OCFG1 C1M MV1 C1V1 C2V1 C3V1 D0 MCS0 SAI0 OM0 HPB MPCV OCFG0 MMute MV0 C1V0 C2V0 C3V0 24/71 STA333BWQS Table 9. Addr 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 Register description Register summary (continued) Name A2cf1 A2cf2 A2cf3 B0cf1 B0cf2 B0cf3 Cfud MPCC1 MPCC2 DCC1 DCC2 FDRC1 FDRC2 Status reserved reserved reserved MPCC15 MPCC14 MPCC7 DCC15 DCC7 FDRC15 FDRC7 PLLUL MPCC6 DCC14 DCC6 FDRC14 FDRC6 FAULT MPCC13 MPCC5 DCC13 DCC5 FDRC13 FDRC5 UVFAULT RO1BACT R01BEND MPCC12 MPCC4 DCC12 DCC4 FDRC12 FDRC4 OVFAULT R5BACT R5BEND R5BBAD D7 C4B23 C4B15 C4B7 C5B23 C5B15 C5B7 D6 C4B22 C4B14 C4B6 C5B22 C5B14 C5B6 D5 C4B21 C4B13 C4B5 C5B21 C5B13 C5B5 D4 C4B20 C4B12 C4B4 C5B20 C5B12 C5B4 D3 C4B19 C4B11 C4B3 C5B19 C5B11 C5B3 RA MPCC11 MPCC3 DCC11 DCC3 FDRC11 FDRC3 D2 C4B18 C4B10 C4B2 C5B18 C5B10 C5B2 R1 MPCC10 MPCC2 DCC10 DCC2 FDRC10 FDRC2 D1 C4B17 C4B9 C4B1 C5B17 C5B9 C5B1 WA MPCC9 MPCC1 DCC9 DCC1 FDRC9 FDRC1 TFAULT R2BACT D0 C4B16 C4B8 C4B0 C5B16 C5B8 C5B0 W1 MPCC8 MPCC0 DCC8 DCC0 FDRC8 FDRC0 TWARN R1BACT OCFAULT OCWARN R4BACT R4BEND R4BBAD R3BACT R3BEND R3BBAD R2BEND R1BEND R2BBAD R1BBAD 6.1 Configuration register A (0x00) D7 FDRB 0 D6 TWAB 1 D5 TWRB 1 D4 IR1 0 D3 IR0 0 D2 MCS2 0 D1 MCS1 1 D0 MCS0 1 6.1.1 Master clock select Table 10. Bit 0 1 2 Master clock select R/W R/W R/W R/W RST 1 1 0 Name MCS0 MCS1 MCS2 Selects the ratio between the input I2S sample frequency and the input clock. Description The STA333BWQS supports sample rates of 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, and 192 kHz. Therefore the internal clock is: " " " 32.768 MHz for 32 kHz 45.1584 MHz for 44.1 kHz, 88.2 kHz, and 176.4 kHz 49.152 MHz for 48 kHz, 96 kHz, and 192 kHz 25/71 Register description STA333BWQS The external clock frequency provided to the XTI pin must be a multiple of the input sample frequency (fs). The relationship between the input clock and the input sample rate is determined by both the MCSx and the IR (iInput rate) register bits. The MCSx bits determine the PLL factor generating the internal clock and the IR bit determines the oversampling ratio used internally Table 11. Input sampling rates IR[1:0] 101 32, 44.1, 48 88.2, 96 176.4, 192 00 01 1X 576fs NA NA 100 128fs 64fs 32fs MCS[2:0] 011 256fs 128fs 64fs 010 384fs 192fs 96fs 001 512fs 256fs 128fs 000 768fs 384fs 192fs Input sample rate Fs (kHz) 6.1.2 Interpolation ratio select Table 12. Bit 4:3 Interpolation ratio select R/W R/W RST 00 Name IR[1:0] Description Selects internal interpolation ratio based on input I2S sample frequency The STA333BWQS has variable interpolation (oversampling) settings such that internal processing and DDX(R) output rates remain consistent. The first processing block interpolates by either 2-times or 1-time (pass-through) or provides a 2-times downsample. The oversampling ratio of this interpolation is determined by the IR bits. Table 13. IR bit settings as a function of input sample rate IR[1:0] 00 00 00 01 01 10 10 1st stage interpolation ratio 2 times oversampling 2 times oversampling 2 times oversampling Pass-through Pass-through 2 times downsampling 2 times downsampling Input sample rate Fs (kHz) 32 44.1 48 88.2 96 176.4 192 26/71 STA333BWQS Register description 6.1.3 Thermal warning recovery bypass Table 14. Bit 5 Thermal warning recovery bypass R/W R/W RST 1 Name TWRB Description 0: thermal warning recovery enabled 1: thermal warning recovery disabled If the thermal warning adjustment is enabled (TWAB=0), then the thermal warning recovery determines if the -3 dB output limit is removed when thermal warning is negative. If TWRB=0 and TWAB=0, then when a thermal warning disappears the -3 dB output limit is removed and the gain is added back to the system. If TWRB=1 and TWAB=0, then when a thermal warning disappears the -3 dB output limit remains until TWRB is changed to zero or the device is reset. 6.1.4 Thermal warning adjustment bypass Table 15. Bit 6 Thermal warning adjustment bypass R/W R/W RST 1 Name TWAB Description 0: thermal warning adjustment enabled 1: thermal warning adjustment disabled The on-chip STA333BWQS power output block provides feedback to the digital controller using inputs to the power control block. The TWARN input is used to indicate a thermal warning condition. When TWARN is asserted (set to 0) for a period of time greater than 400 ms, the power control block forces a -3 dB output limit (determined by TWOCL in Coeff RAM) to the modulation limit in an attempt to eliminate the thermal warning condition. Once the thermal warning output limit adjustment is applied, it remains in this state until reset, unless FDRB = 0. 6.1.5 Fault detect recovery bypass Table 16. Bit 7 Fault detect recovery bypass R/W R/W RST 0 Name FDRB Description 0: fault detect recovery enabled 1: fault detect recovery disabled The on-chip STA333BWQS power output block provides feedback to the digital controller using inputs to the power control block. The FAULT input is used to indicate a fault condition (either over-current or thermal). When FAULT is asserted (set to 0), the power control block attempts a recovery from the fault by asserting the tri-state output (setting it to 0 which directs the power output block to begin recovery), holds it at 0 for period of time in the range of 0.1 ms to 1 s as defined by the fault-detect recovery constant register (FDRC registers 0x29, 0x2A), then toggles it back to 1. This sequence is repeated as log as the fault indication exists. This feature is enabled by default but can be bypassed by setting the FDRB control bit to 1. 27/71 Register description STA333BWQS 6.2 Configuration register B (0x01) D7 C2IM 1 D6 C1IM 0 D5 DSCKE 0 D4 SAIFB 0 D3 SAI3 0 D2 SAI2 0 D1 SAI1 0 D0 SAI0 0 6.2.1 Serial audio input interface format Table 17. Bit 0 1 2 3 Serial audio input interface format R/W R/W R/W R/W R/W RST 0 0 0 0 Name SAI0 SAI1 SAI2 SAI3 Determines the interface format of the input serial digital audio interface. Description 6.2.2 Serial data interface The STA333BWQS audio serial input was designed to interface with standard digital audio components and to accept a number of serial data formats. STA333BWQS always acts a slave when receiving audio input from standard digital audio components. Serial data for two channels is provided using three inputs: left/right clock LRCKI, serial clock BICKI, and serial data 1 and 2 SDI12. The SAI register (configuration register B (0x01), bits D3 to D0) and the SAIFB register (configuration register B (0x01), bit D4) are used to specify the serial data format. The default serial data format is I2S, MSB-first. Available formats are shown in the tables and figure that follow. 6.2.3 Serial data first bit Table 18. Serial data first bit Format MSB-first LSB-first SAIFB 0 1 28/71 STA333BWQS Table 19. BICKI 32fs 0001 0000 0001 0010 48fs 0110 1010 1110 0000 0001 0010 64fs 0110 1010 1110 0 0 0 Right-justified 20-bit data Right-justified 18-bit data Right-justified 16-bit data 0 0 0 0 0 0 Right-justified 20-bit data Right-justified 18-bit data Right-justified 16-bit data I2S 16 to 24-bit data 0 0 0 0 Register description Support serial audio input formats for MSB-first (SAIFB = 0) SAI [3:0] 0000 SAIFB 0 I2S 15-bit data Left/right-justified 16-bit data I2S 16 to 23-bit data Left-justified 16 to 24-bit data Right-justified 24-bit data Interface format Left-justified 16 to 24-bit data Right-justified 24-bit data Table 20. BICKI 32fs Supported serial audio input formats for LSB-first (SAIFB = 1) SAI [3:0] 1100 1110 0100 0100 1000 1100 0001 0101 SAIFB 1 1 1 1 1 1 1 1 1 1 1 1 1 1 I2S 15-bit data Left/right-justified 16-bit data I2S 23-bit data I2S 20-bit data I2S 18-bit data LSB first I2S 16-bit data Left-justified 24-bit data Left-justified 20-bit data Left-justified 18-bit data Left-justified 16-bit data Right-justified 24-bit data Right-justified 20-bit data Right-justified 18-bit data Right-justified 16-bit data Interface Format 48fs 1001 1101 0010 0110 1010 1110 29/71 Register description Table 20. BICKI STA333BWQS Supported serial audio input formats for LSB-first (SAIFB = 1) (continued) SAI [3:0] 0000 0100 1000 1100 0001 0101 SAIFB 1 1 1 1 1 1 1 1 1 1 1 1 I S 24-bit data I2S 20-bit data I2S 18-bit data LSB first I2S 16-bit data Left-justified 24-bit data Left-justified 20-bit data Left-justified 18-bit data Left-justified 16-bit data Right-justified 24-bit data Right-justified 20-bit data Right-justified 18-bit data Right-justified 16-bit data 2 Interface Format 64fs 1001 1101 0010 0110 1010 1110 6.2.4 Delay serial clock enable Table 21. Bit Delay serial clock enable R/W RST Name Description 0: no serial clock delay 1: serial clock delay by 1 core clock cycle to tolerate anomalies in some I2S master devices 5 R/W 0 DSCKE 6.2.5 Channel input mapping Table 22. Bit 6 7 Channel input mapping R/W R/W R/W RST 0 1 Name C1IM C2IM Description 0: processing channel 1 receives Left I2S Input 1: processing channel 1 receives Right I2S Input 0: processing channel 2 receives Left I2S Input 1: processing channel 2 receives Right I2S Input Each channel received via I2S can be mapped to any internal processing channel via the Channel Input Mapping registers. This allows for flexibility in processing. The default settings of these registers map each I2S input channel to its corresponding processing channel. 30/71 STA333BWQS Register description 6.3 Configuration register C (0x02) D7 OCRB 1 D6 D5 CSZ3 0 D4 CSZ2 1 D3 CSZ1 0 D2 CSZ0 1 D1 OM1 1 D0 OM0 1 6.3.1 DDX(R) power output mode Table 23. Bit 0 1 DXX power output mode R/W R/W R/W RST 1 1 Name OM0 Selects configuration of DDX output. OM1 Description The DDX power output mode selects how the DDX output timing is configured. Different power devices use different output modes. Table 24. Output modes Output stage / mode Drop Compensation Discrete Output Stage, Tapered Compensation Full Power Mode Variable Drop Compensation (CSZx bits) OM[1,0] 00 01 10 11 6.3.2 DDX(R) compensating pulse size register Table 25. Bit 2 3 4 5 DXX compensating pulse size register R/W R/W R/W R/W R/W RST 1 0 1 0 Name CSZ0 CSZ1 CSZ2 CSZ3 When OM[1,0] = 11, this register determines the size of the DDX compensating pulse from 0 clock ticks to 15 clock periods. Description Table 26. Table 6: Compensating pulse size Compensating Pulse Size 0 ns (0 tick) compensating pulse size 20 ns (1 tick) clock period compensating pulse size ... 300 ns (15 tick) clock period compensating pulse size CSZ[3:0] 0000 0001 ... 1111 31/71 Register description STA333BWQS 6.3.3 Over-current warning detect adjustment bypass Table 27. Bit 7 Over-current warning detect adjustment bypass R/W R/W RST 1 Name OCRB Description 0: over-current warning adjustment enabled 1: over-current warning adjustment disabled The OCWARN input is used to indicate an over-current warning condition. When OCWARN is asserted (set to 0), the power control block forces an adjustment to the modulation limit (default is -3 dB) in an attempt to eliminate the over-current warning condition. Once the over-current warning volume adjustment is applied, it remains in this state until reset is applied. The level of adjustment can be changed via the TWOCL (thermal warning/over current limit) setting which is address 0x37 of the user defined coefficient RAM. 6.4 Configuration register D (0x03) D7 MME 0 D6 ZDE 1 D5 DRC 0 D4 BQL 0 D3 PSL 0 D2 DSPB 0 D1 DEMP 0 D0 HPB 0 6.4.1 High-pass filter bypass Table 28. Bit 0 High-pass filter bypass R/W R/W RST 0 Name HPB Description Setting of one bypasses internal AC coupling digital high-pass filter The STA333BWQS features an internal digital high-pass filter for the purpose of AC coupling. The purpose of this filter is to prevent DC signals from passing through a DDX amplifier. DC signals can cause speaker damage. When HPB = 0, this filter is enabled. 6.4.2 De-emphasis Table 29. Bit 1 De-emphasis R/W R/W RST 0 Name DEMP 0: no de-emphasis 1: de-emphasis Description Setting the DEMP bit enables de-emphasis on all channels 32/71 STA333BWQS Register description 6.4.3 DSP bypass Table 30. Bit 2 DSP bypass R/W R/W RST 0 Name DSPB Description 0: normal operation 1: bypass of biquad and bass/treble functionality Setting the DSPB bit bypasses the EQ functionality of the STA333BWQS. 6.4.4 Post-scale link Table 31. Bit 3 Post-scale link R/W R/W RST 0 Name PSL Description 0: each channel uses individual post-scale value 1: each channel uses channel 1 post-scale value Post-scale functionality can be used for power-supply error correction. For multi-channel applications running off the same power-supply, the post-scale values can be linked to the value of channel 1 for ease of use and update the values faster. 6.4.5 Biquad coefficient link Table 32. Bit 4 Biquad coefficient link R/W R/W RST 0 Name BQL Description 0: each channel uses coefficient values 1: each channel uses channel 1 coefficient values For ease of use, all channels can use the biquad coefficients loaded into the Channel 1 Coefficient RAM space by setting the BQL bit to 1. Therefore, any EQ updates only have to be performed once. 6.4.6 Dynamic range compression/anti-clipping bit Table 33. Bit 5 Dynamic range compression/anti-clipping bit R/W R/W RST 0 Name DRC Description 0: limiters act in anti-clipping mode 1: limiters act in dynamic range compression mode Both limiters can be used in one of two ways, anti-clipping or dynamic range compression. When used in anti-clipping mode the limiter threshold values are constant and dependent on the limiter settings. In dynamic range compression mode the limiter threshold values vary with the volume settings allowing a nighttime listening mode that provides a reduction in the dynamic range regardless of the volume level. 33/71 Register description STA333BWQS 6.4.7 Zero-detect mute enable Table 34. Bit 6 Zero-detect mute enable R/W R/W RST 1 Name ZDE Description Setting of 1 enables the automatic zero-detect mute Setting the ZDE bit enables the zero-detect automatic mute. The zero-detect circuit looks at the data for each processing channel at the output of the crossover (bass management) filter. If any channel receives 2048 consecutive zero value samples (regardless of fs) then that individual channel is muted if this function is enabled. 6.4.8 MiamiMode enable Table 35. Bit 7 MiamiMode enable RST 0 Name MME Description 0: sub mix into left/right disabled 1: sub mix into left/right enabled R/W R/W 6.5 Configuration register E (0x04) D7 SVE 1 D6 ZCE 1 D5 DCCV 0 D4 PWMS 0 D3 AME 0 D2 NSBW 0 D1 MPC 1 D0 MPCV 0 6.5.1 Max power correction variable Table 36. Bit 0 Max power correction variable R/W R/W RST 0 Name MPCV Description 0: use standard MPC coefficient 1: use MPCC bits for MPC coefficient 6.5.2 Max power correction Table 37. Bit 1 Max power correction R/W R/W RST 1 Name MPC Description Setting of 1 enables Power Bridge correction for THD reduction near maximum power output. Setting the MPC bit turns on special processing that corrects the STA333BWQS power device at high power. This mode should lower the THD+N of a full DDX system at maximum power output and slightly below. If enabled, MPC is operational in all output modes except tapered (OM[1,0] = 01) and binary. When OCFG = 00, MPC will not effect channels 3 and 4, the line-out channels. 34/71 STA333BWQS Register description 6.5.3 Noise-shaper bandwidth selection Table 38. Bit 2 R/W R/W Noise-shaper bandwidth selection RST 0 Name NSBW 1: third-order NS 0: fourth-order NS Description 6.5.4 AM mode enable Table 39. Bit 3 R/W R/W AM mode enable RST 0 Name AME Description 0: normal DDX operation 1: AM reduction mode DDX operation STA333BWQS features a DDX processing mode that minimizes the amount of noise generated in frequency range of AM radio. This mode is intended for use when DDX is operating in a device with an AM tuner active. The SNR of the DDX processing is reduced to approximately 83 dB in this mode, which is still greater than the SNR of AM radio. 6.5.5 PWM speed mode Table 40. Bit 4 R/W R/W PWM speed mode RST 0 Name PWMS Description 0: normal speed (384 kHz) all channels 1: odd speed (341.3 kHz) all channels 6.5.6 Distortion compensation variable enable Table 41. Bit 5 R/W R/W Distortion compensation variable enable RST 0 Name DCCV Description 0: uses preset DC coefficient 1: uses DCC coefficient 6.5.7 Zero-crossing volume enable Table 42. Bit 6 R/W R/W Zero-crossing volume enable RST 1 Name ZCE Description 1: volume adjustments only occur at digital zero-crossings 0: volume adjustments occur immediately The ZCE bit enables zero-crossing volume adjustments. When volume is adjusted on digital zero-crossings no clicks are audible. 35/71 Register description STA333BWQS 6.5.8 Soft volume update enable Table 43. Bit 7 R/W R/W Soft volume update enable RST 1 Name SVE Description 1: volume adjustments ramp according to SVR settings 0: volume adjustments occur immediately 6.6 Configuration register F (0x05) D7 EAPD 0 D6 PWDN 1 D5 ECLE 0 D4 LDTE 1 D3 BCLE 1 D2 IDE 1 D1 OCFG1 0 D0 OCFG0 0 6.6.1 Output configuration Table 44. Bit 0 1 Output configuration R/W R/W R/W RST 0 0 Name OCFG0 Selects the output configuration OCFG1 Description Table 45. OCFG[1:0] Output configuration engine selection Output configuration 2-channel (full-bridge) power, 2 channel data-out: 1A/1B 1A/1B 2A/2B 2A/2B Line out1 3A/3B Line out2 4A/4B Line out configuration determined by LOC register 2(half-bridge).1(full-bridge) on-board power: 1A 1A binary 0 2A 1B binary 90 3A/3B 2A/2B binary 45 1A/B 3A/B binary 0 2A/B 4A/B binary 90 2-channel (full-bridge) power, 1 channel DDX: 1A/1B 1A/1B 2A/2B 2A/2B 3A/3B 3A/3B EAPDEXT and TWARNEXT Active 1-channel mono-parallel: 3A 1A/1B w/ C3BO 45 3B 2A/2B w/ C3BO 45 1A/1B 3A/3B 2A/2B 4A/4B Config PIN 00 0 01 0 10 0 11 1 36/71 STA333BWQS Note: Register description To the left of the arrow is the processing channel. When using channel output mapping, any of the three processing channel outputs can be used for any of the three inputs. OCFG = 00 (default value) Half Bridge Figure 9. Figure 10. OCFG = 01 OUT1A Channel 1 Half Bridge Half Bridge Channel 1 OUT1A OUT1B OUT2A Half Bridge Half Bridge Channel 2 OUT1B OUT2A Channel 2 Half Bridge Half Bridge OUT2B OUT3A OUT3B LPF Channel 3 LineOut 1 Half Bridge OUT2B OUT4A OUT4B LPF LineOut 2 Figure 11. OCFG = 10 Half Bridge Figure 12. OCFG = 11 OUT1A Half Bridge OUT1A Channel 1 Half Bridge OUT1B OUT2A Half Bridge OUT1B Channel 3 Half Bridge Half Bridge OUT2A Channel 2 Half Bridge Half Bridge OUT2B OUT2B OUT3A OUT3B EAPD Power Device Channel 3 OUT3A OUT3B Channel 1 OUT4A OUT4B Channel 2 STA333BWQS can be configured to support different output configurations. For each PWM output channel a "PWM slot" is defined. PWM slot is always 1 / (8 x Fs) seconds length. The PWM slot define the maximum extension for PWM rise and fall edge, that is, rising edge as far as the falling edge cannot range outside PWM slot boundaries. Figure 13. STA333BWQS output mapping scheme DDX1A OUT1A DDX1B DDX2A OUT1B OUT1A OUT1B DDXTM modulator DDX2B DDX3A DDX3B DDX4A DDX4B OUT2B OUT2A Power Bridge OUT2A OUT2B REMAP OUT3A OUT3B OUT4A OUT4B 37/71 Register description STA333BWQS For each configuration the PWM from the digital driver are mapped in different way to the power stage: 2.0 channels, two full bridges (OCFG = 00) " " " " " " " " " " " " DDX1A ' OUT1A DDX1B ' OUT1B DDX2A ' OUT2A DDX2B ' OUT2B DDX3A ' OUT3A DDX3B ' OUT3B DDX4A ' OUT4A DDX4B ' OUT4B DDX1A/1B configured as ternary DDX2A/2B configured as ternary DDX3A/3B configured as lineout ternary DDX4A/4B configured as lineout ternary On channel 3 line out (LOC bits = "00") the same datas as channel 1 processing are sent. On channel 4 line out (LOC bits = "00") the same datas as channel 2 processing are sent. In this configuration, no volume control or EQ have effect on channel 3 and 4. In this configuration the PWM slot phase is the following as shown in the next figures: Figure 14. 2.0 channels (OCFG = 00) PWM slots. OUT1A OUT1B OUT2A OUT2B OUT3A OUT3B OUT4A OUT4B 38/71 STA333BWQS Register description 2.1 channels, two half bridges + one full bridge (OCFG = 01) " " " " " " " " " " " " DDX1A ' OUT1A DDX2A ' OUT1B DDX3A ' OUT2A DDX3B ' OUT2B DDX1A ' OUT3A DDX1B ' OUT3B DDX2A ' OUT4A DDX2B ' OUT4B DDX1A/1B configured as binary DDX2A/2B configured as binary DDX3A/3B configured as binary DDX4A/4B is not used In this configuration, channel 3 has full control (volume, EQ, etc...). On OUT3/OUT4 channels the channel 1 and channel 2 PWM are replicated. In this configuration the PWM slot phase is the following as shown in the next figures: Figure 15. 2.1 channels (OCFG = 01) PWM slots. OUT1A OUT1B OUT2A OUT2B OUT3A OUT3B OUT4A OUT4B 39/71 Register description STA333BWQS 2.1 channels, two fullbridge + one external full bridge (OCFG = 10) " " " " " " " " " " " " DDX1A ' OUT1A DDX1B ' OUT1B DDX2A ' OUT2A DDX2B ' OUT2B DDX3A ' OUT3A DDX3B ' OUT3B EAPD ' OUT4A TWARN OUT4B DDX1A/1B configured as ternary DDX2A/2B configured as ternary DDX3A/3B configured as ternary DDX4A/4B is not used In this configuration, channel 3 has full control (volume, EQ, etc...). On OUT4 channel the external bridge control signals are muxed. In this configuration the PWM slot phase is the following as shown in the next figures: Figure 16. 2.1 channels (OCFG = 10) PWM slots. OUT1A OUT1B OUT2A OUT2B OUT3A OUT3B 6.6.2 Invalid input detect mute enable Table 46. Bit 2 Invalid input detect mute enable R/W R/W RST 1 Name IDE Description Setting of 1 enables the automatic invalid input detect mute Setting the IDE bit enables this function, which looks at the input I2S data and will automatically mute if the signals are perceived as invalid. 40/71 STA333BWQS Register description 6.6.3 Binary output mode clock loss detection Table 47. Bit 3 Binary output mode clock loss detection R/W R/W RST 1 Name BCLE Description Binary output mode clock loss detection enable Detects loss of input MCLK in binary mode and will output 50% duty cycle. 6.6.4 LRCK double trigger protection Table 48. Bit 4 LRCK double trigger protection R/W R/W RST 1 Name LDTE Description LRCLK double trigger protection enable Actively prevents double trigger of LRCLK. 6.6.5 Auto EAPD on clock loss Table 49. Bit 5 Auto EAPD on clock loss R/W R/W RST 0 Name ECLE Description Auto EAPD on clock loss When active, issues a power device power down signal (EAPD) on clock loss detection. 6.6.6 IC power down Table 50. Bit 7 IC power down R/W R/W RST 1 Name PWDN Description 0: IC power down low-power condition 1: IC normal operation The PWDN register is used to place the IC in a low-power state. When PWDN is written as 0, the output begins a soft-mute. After the mute condition is reached, EAPD is asserted to power down the power-stage, then the master clock to all internal hardware expect the I2C block is gated. This places the IC in a very low power consumption state. 6.6.7 External amplifier power down Table 51. Bit 7 External amplifier power down R/W R/W RST 0 Name EAPD Description 0: external power stage power down active 1: normal operation The EAPD register directly disables/enables the internal power circuitry. When EAPD = 0, the internal power section is placed on a low-power state (disabled). This register also controls the DDX4B/EAPD output pin when OCFG = 10. 41/71 Register description STA333BWQS 6.7 6.7.1 Volume control registers (0x06 to 0x0A) Mute/line output configuration register D7 LOC1 0 D6 LOC0 0 D5 D4 D3 C3M 0 D2 C2M 0 D1 C1M 0 D0 MMUTE 0 Table 52. Line output configuration Line output configuration Line output fixed, no volume, no EQ Line output variable, CH3 volume effects line output, no EQ Line output variable with EQ, CH3 volume effects line output LOC[1:0] 00 01 10 Line output is only active when OCFG = 00. In this case LOC determines the line output configuration. The source of the line output is always the channel 1 and 2 inputs. 6.7.2 Master volume register D7 MV7 1 D6 MV6 1 D5 MV5 1 D4 MV4 1 D3 MV3 1 D2 MV2 1 D1 MV1 1 D0 MV0 1 6.7.3 Channel 1 volume D7 C1V7 0 D6 C1V6 1 D5 C1V5 1 D4 C1V4 0 D3 C1V3 0 D2 C1V2 0 D1 C1V1 0 D0 C1V0 0 6.7.4 Channel 2 volume D7 C2V7 0 D6 C2V6 1 D5 C2V5 1 D4 C2V4 0 D3 C2V3 0 D2 C2V2 0 D1 C2V1 0 D0 C2V0 0 6.7.5 Channel 3 / line output volume D7 C3V7 0 D6 C3V6 1 D5 C3V5 1 D4 C3V4 0 D3 C3V3 0 D2 C3V2 0 D1 C3V1 0 D0 C3V0 0 The volume structure of the STA333BWQS consists of individual volume registers for each channel and a master volume register that provides an offset to each channels volume setting. The individual channel volumes are adjustable in 0.5 dB steps from +48 dB to -80 dB. As an example if C3V = 0x00 or +48 dB and MV = 0x18 or -12 dB, then the total gain for channel 3 = +36 dB. 42/71 STA333BWQS Register description The master mute, when set to 1, mutes all channels at once, whereas the individual channel mutes (CxM) mutes only that channel. Both the master mute and the channel mutes provide a "soft mute" with the volume ramping down to mute in 4096 samples from the maximum volume setting at the internal processing rate (~96 kHz). A "hard mute" can be obtained by putting a value of 0xFF (255) to any channel volume register or the master volume register. When volume offsets are provided via the master volume register any channel that whose total volume is less than -80 dB is muted. All changes in volume take place at zero-crossings when ZCE = 1 (configuration register F) on a per channel basis as this creates the smoothest possible volume transitions. When ZCE=0, volume updates occur immediately. Table 53. Master volume offset as a function of MV[7:0] Volume offset from channel value 0 dB -0.5 dB -1 dB ... -38 dB ... -127.5 dB Hard master mute MV[7:0] 00000000 (0x00) 00000001 (0x01) 00000010 (0x02) ... 01001100 (0x4C) ... 11111110 (0xFE) 11111111 (0xFF) Table 54. Channel volume as a function of CxV[7:0] Volume +48 dB +47.5 dB +47 dB ... +0.5 dB 0 dB -0.5 dB ... -59.5 dB -60 dB -61 dB -62 dB ... -80 dB Hard channel mute CxV[7:0] 00000000 (0x00) 00000001 (0x01) 00000010 (0x02) ... 01011111 (0x5F) 01100000 (0x60) 01100001 (0x61) ... 11010111 (0xD7) 11011000 (0xD8) 11011001 (0xD9) 11011010 (0xDA) ... 11101100 (0xEC) 11101101 (0xED) 43/71 Register description Table 54. Channel volume as a function of CxV[7:0] (continued) Volume ... Hard channel mute STA333BWQS CxV[7:0] ... 11111111 (0xFF) 6.8 6.8.1 Auto mode registers (0x0B and 0x0C) AutoMode register 1 (0x0B) D7 D6 D5 AMGC1 0 D4 AMGC2 0 D3 D2 D1 D0 Table 55. AutoMode gain compression/limiters selection Mode User programmable GC AC no clipping 2.1 AC limited clipping (10%) 2.1 DRC nighttime listening mode 2.1 AMGC[1:0] 00 01 10 11 6.8.2 AutoMode register 2 (0x0C) D7 XO3 0 D6 XO2 0 D5 XO1 0 D4 XO0 0 D3 AMAM2 0 D2 AMAM1 0 D1 AMAM0 0 D0 AMAME 0 6.8.3 AM interference frequency switching Table 56. Bit AM interference frequency switching RST Name Description AutoMode AM Enable 0: switching frequency determined by PWMS setting 1: switching frequency determined by AMAM settings R/W 0 R/W 0 AMAME Table 57. AutoMode AM switching frequency selection 48 kHz / 96 kHz input Fs 0.535 MHz to 0.720 MHz 0.721 MHz to 0.900 MHz 0.901 MHz to 1.100 MHz 1.101 MHz to 1.300 MHz 1.301 MHz to 1.480 MHz 44.1 kHz / 88.2 kHz input Fs 0.535 MHz to 0.670 MHz 0.671 MHz to 0.800 MHz 0.801 MHz to 1.000 MHz 1.001 MHz to 1.180 MHz 1.181 MHz to 1.340 MHz AMAM[2:0] 000 001 010 011 100 44/71 STA333BWQS Table 57. Register description AutoMode AM switching frequency selection (continued) 48 kHz / 96 kHz input Fs 1.481 MHz to 1.600 MHz 1.601 MHz to 1.700 MHz 44.1 kHz / 88.2 kHz input Fs 1.341 MHz to 1.500 MHz 1.501 MHz to 1.700 MHz AMAM[2:0] 101 110 6.8.4 Bass management crossover Table 58. Bit 4 5 6 7 Base management crossover R/W R/W R/W R/W R/W RST 0 0 0 0 Name XO0 XO1 XO2 XO3 Selects the bass-management crossover frequency. A 1st-order high-pass filter (channels 1 and 2) or a 2nd-order low-pass filter (channel 3) at the selected frequency is performed. Description Table 59. Bass management crossover frequency Crossover frequency User-Defined 80 Hz 100 Hz 120 Hz 140 Hz 160 Hz 180 Hz 200 Hz 220 Hz 240 Hz 260 Hz 280 Hz 300 Hz 320 Hz 340 Hz 360 Hz XO[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 45/71 Register description STA333BWQS 6.9 Channel configuration registers ( 0x0E to 0x10) D7 C1OM1 0 D7 C2OM1 0 D7 C3OM1 1 D6 C1OM0 0 D6 C2OM0 1 D6 C3OM0 0 D5 C1LS1 0 D5 C2LS1 0 D5 C3LS1 0 D4 C1LS0 0 D4 C2LS0 0 D4 C3LS0 0 D3 C1BO 0 D3 C2BO 0 D3 C3BO 0 D2 C1VPB 0 D2 C2VPB 0 D2 C3VPB 0 D1 C1EQBP 0 D1 C2EQBP 0 D1 D0 C1TCB 0 D0 C2TCB 0 D0 6.9.1 Tone control bypass Tone control (bass/treble) can be bypassed on a per channel basis for channels 1 and 2. CxTCB: 0: perform tone control on channel X, normal operation 1: bypass tone control on channel X 6.9.2 EQ bypass EQ control can be bypassed on a per channel basis for channels 1 and 2. If EQ control is bypassed on a given channel the prescale and all filters (high-pass, biquads, de-emphasis, bass, treble in any combination) are bypassed for that channel. CxEQBP: 0: perform EQ on channel X, normal operation 1: bypass EQ on channel X 6.9.3 Volume bypass Each channel contains an individual channel volume bypass. If a particular channel has volume bypassed via the CxVBP = 1 register then only the channel volume setting for that particular channel affects the volume setting, the master volume setting will not affect that channel. 6.9.4 Binary output enable registers Each individual channel output can be set to output a binary PWM stream. In this mode output A of a channel is considered the positive output and output B is negative inverse. CxBO: 0: DDX tri-state output, normal operation 1: binary output 46/71 STA333BWQS Register description 6.9.5 Limiter select Limiter selection can be made on a per-channel basis according to the channel limiter select bits. Table 60. . Channel limiter mapping as a function of CxLS bits Channel limiter mapping Channel has limiting disabled Channel is mapped to limiter #1 Channel is mapped to limiter #2 CxLS[1:0] 00 01 10 6.9.6 Output mapping Output mapping can be performed on a per channel basis according to the CxOM channel output mapping bits. Each input into the output configuration engine can receive data from any of the three processing channel outputs. Table 61. . Channel output mapping as a function of CxOM bits Channel x output source from Channel1 Channel 2 Channel 3 CxOM[1,0] 00 01 10 6.10 6.10.1 Tone control register (0x11) Tone control D7 TTC3 0 D6 TTC2 1 D5 TTC1 1 D4 TTC0 1 D3 BTC3 0 D2 BTC2 1 D1 BTC1 1 D0 BTC0 1 Table 62. Tone control boost/cut as a function of BTC and TTC bits Boost/Cut -12 dB -12 dB ... -4 dB -2 dB 0 dB +2 dB +4 dB ... BTC[3:0]/TTC[3:0] 0000 0001 ... 0111 0110 0111 1000 1001 ... 47/71 Register description Table 62. Tone control boost/cut as a function of BTC and TTC bits Boost/Cut +12 dB +12 dB +12 dB STA333BWQS BTC[3:0]/TTC[3:0] 1101 1110 1111 6.11 6.11.1 Dynamics control registers (0x12 to 0x15) Limiter 1 attack/release rate D7 L1A3 0 D6 L1A2 1 D5 L1A1 1 D4 L1A0 0 D3 L1R3 1 D2 L1R2 0 D1 L1R1 1 D0 L1R0 0 6.11.2 Limiter 1 attack/release threshold D7 L1AT3 0 D6 L1AT2 1 D5 L1AT1 1 D4 L1AT0 0 D3 L1RT3 1 D2 L1RT2 0 D1 L1RT1 0 D0 L1RT0 1 6.11.3 Limiter 2 attack/release rate D7 L2A3 0 D6 L2A2 1 D5 L2A1 1 D4 L2A0 0 D3 L2R3 1 D2 L2R2 0 D1 L2R1 1 D0 L2R0 0 6.11.4 Limiter 2 attack/release threshold D7 L2AT3 0 D6 L2AT2 1 D5 L2AT1 1 D4 L2AT0 0 D3 L2RT3 1 D2 L2RT2 0 D1 L2RT1 0 D0 L2RT0 1 The STA333BWQS includes two independent limiter blocks. The purpose of the limiters is to automatically reduce the dynamic range of a recording to prevent the outputs from clipping in anti-clipping mode or to actively reduce the dynamic range for a better listening environment such as a night-time listening mode which is often needed for DVDs. The two modes are selected via the DRC bit in Configuration Register F, bit 0 address 0x05. Each channel can be mapped to either limiter or not mapped, meaning that channel will clip when 0dBFS is exceeded. Each limiter looks at the present value of each channel that is mapped to it, selects the maximum absolute value of all these channels, performs the limiting algorithm on that value, and then if needed adjusts the gain of the mapped channels in unison. The limiter attack thresholds are determined by the LxAT registers. It is recommended in anti-clipping mode to set this to 0dBFS, which corresponds to the maximum unclipped output power of a DDX amplifier. Since gain can be added digitally within STA333BWQS it is possible to exceed 0dBFS or any other LxAT setting, when this occurs, the limiter, when 48/71 STA333BWQS Register description active, automatically starts reducing the gain. The rate at which the gain is reduced when the attack threshold is exceeded is dependent upon the attack rate register setting for that limiter. The gain reduction occurs on a peak-detect algorithm. The release of limiter, when the gain is again increased, is dependent on a RMS-detect algorithm. The output of the volume/limiter block is passed through a RMS filter. The output of this filter is compared to the release threshold, determined by the Release Threshold register. When the RMS filter output falls below the release threshold, the gain is again increased at a rate dependent upon the Release Rate register. The gain can never be increased past it's set value and therefore the release only occurs if the limiter has already reduced the gain. The release threshold value can be used to set what is effectively a minimum dynamic range, this is helpful as over-limiting can reduce the dynamic range to virtually zero and cause program material to sound "lifeless". In AC mode, the attack and release thresholds are set relative to full-scale. In DRC mode, the attack threshold is set relative to the maximum volume setting of the channels mapped to that limiter and the release threshold is set relative to the maximum volume setting plus the attack threshold. Figure 17. Basic limiter and volume flow diagram 49/71 Register description STA333BWQS Table 63. LxA[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Limiter attack rate as a function of LxA bits Attack Rate dB/ms 3.1584 2.7072 2.2560 1.8048 1.3536 0.9024 0.4512 0.2256 0.1504 0.1123 0.0902 0.0752 0.0645 0.0564 0.0501 0.0451 Slow Fast Table 64. LxR[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Limiter release rate as a function of LxR bits Release Rate dB/ms 0.5116 0.1370 0.0744 0.0499 0.0360 0.0299 0.0264 0.0208 0.0198 0.0172 0.0147 0.0137 0.0134 0.0117 0.0110 0.0104 Slow Fast 50/71 STA333BWQS Register description Anti-clipping mode Table 65. Limiter attack threshold as a function of LxAT bits (AC-Mode). AC(dB relative to FS) -12 -10 -8 -6 -4 -2 0 +2 +3 +4 +5 +6 +7 +8 +9 +10 Table 66. Limiter release threshold as a function of LxRT bits (AC-Mode). AC(dB relative to FS) - -29 dB -20 dB -16 dB -14 dB -12 dB -10 dB -8 dB -7 dB -6 dB -5 dB -4 dB -3 dB -2 dB -1 dB -0 dB LxAT[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 LxRT[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 51/71 Register description STA333BWQS Dynamic range compression mode Table 67. Limiter attack threshold as a function of LxAT bits (DRC-Mode). DRC(dB relative to Volume) -31 -29 -27 -25 -23 -21 -19 -17 -16 -15 -14 -13 -12 -10 -7 -4 Table 68. Limiter release threshold as a as a function of LxRT bits (DRC-Mode). DRC(db relative to Volume + LxAT) - -38 dB -36 dB -33 dB -31 dB -30 dB -28 dB -26 dB -24 dB -22 dB -20 dB -18 dB -15 dB -12 dB -9 dB -6 dB LxAT[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 LxRT[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 6.12 6.12.1 User-defined coefficient control registers (0x16 to 0x26) Coefficient address register D7 D6 D5 CFA5 0 D4 CFA4 0 D3 CFA3 0 D2 CFA2 0 D1 CFA1 0 D0 CFA0 0 6.12.2 Coefficient b1 data register bits 23:16 D7 C1B23 0 D6 C1B22 0 D5 C1B21 0 D4 C1B20 0 D3 C1B19 0 D2 C1B18 0 D1 C1B17 0 D0 C1B16 0 52/71 STA333BWQS Register description 6.12.3 Coefficient b1 data register bits 15:8 D7 C1B15 0 D6 C1B14 0 D5 C1B13 0 D4 C1B12 0 D3 C1B11 0 D2 C1B10 0 D1 C1B9 0 D0 C1B8 0 6.12.4 Coefficient b1 data register bits 7:0 D7 C1B7 0 D6 C1B6 0 D5 C1B5 0 D4 C1B4 0 D3 C1B3 0 D2 C1B2 0 D1 C1B1 0 D0 C1B0 0 6.12.5 Coefficient b2 data register bits 23:16 D7 C2B23 0 D6 C2B22 0 D5 C2B21 0 D4 C2B20 0 D3 C2B19 0 D2 C2B18 0 D1 C2B17 0 D0 C2B16 0 6.12.6 Coefficient b2 data register bits 15:8 D7 C2B15 0 D6 C2B14 0 D5 C2B13 0 D4 C2B12 0 D3 C2B11 0 D2 C2B10 0 D1 C2B9 0 D0 C2B8 0 6.12.7 Coefficient b2 data register bits 7:0 D7 C2B7 0 D6 C2B6 0 D5 C2B5 0 D4 C2B4 0 D3 C2B3 0 D2 C2B2 0 D1 C2B1 0 D0 C2B0 0 6.12.8 Coefficient a1 data register bits 23:16 D7 C1B23 0 D6 C1B22 0 D5 C1B21 0 D4 C1B20 0 D3 C1B19 0 D2 C1B18 0 D1 C1B17 0 D0 C1B16 0 6.12.9 Coefficient a1 data register bits 15:8 D7 C3B15 0 D6 C3B14 0 D5 C3B13 0 D4 C3B12 0 D3 C3B11 0 D2 C3B10 0 D1 C3B9 0 D0 C3B8 0 53/71 Register description STA333BWQS 6.12.10 Coefficient a1 data register bits 7:0 D7 C3B7 0 D6 C3B6 0 D5 C3B5 0 D4 C3B4 0 D3 C3B3 0 D2 C3B2 0 D1 C3B1 0 D0 C3B0 0 6.12.11 Coefficient a2 data register bits 23:16 D7 C4B23 0 D6 C4B22 0 D5 C4B21 0 D4 C4B20 0 D3 C4B19 0 D2 C4B18 0 D1 C4B17 0 D0 C4B16 0 6.12.12 Coefficient a2 data register bits 15:8 D7 C4B15 0 D6 C4B14 0 D5 C4B13 0 D4 C4B12 0 D3 C4B11 0 D2 C4B10 0 D1 C4B9 0 D0 C4B8 0 6.12.13 Coefficient a2 data register bits 7:0 D7 C4B7 0 D6 C4B6 0 D5 C4B5 0 D4 C4B4 0 D3 C4B3 0 D2 C4B2 0 D1 C4B1 0 D0 C4B0 0 6.12.14 Coefficient b0 data register bits 23:16 D7 C5B23 0 D6 C5B22 0 D5 C5B21 0 D4 C5B20 0 D3 C5B19 0 D2 C5B18 0 D1 C5B17 0 D0 C5B16 0 6.12.15 Coefficient b0 data register bits 15:8 D7 C5B15 0 D6 C5B14 0 D5 C5B13 0 D4 C5B12 0 D3 C5B11 0 D2 C5B10 0 D1 C5B9 0 D0 C5B8 0 6.12.16 Coefficient b0 data register bits 7:0 D7 C5B7 0 D6 C5B6 0 D5 C5B5 0 D4 C5B4 0 D3 C5B3 0 D2 C5B2 0 D1 C5B1 0 D0 C5B0 0 54/71 STA333BWQS Register description 6.12.17 Coefficient write/read control register D7 D6 D5 D4 D3 RA 0 D2 R1 0 D1 WA 0 D0 W1 0 Coefficients for user-defined EQ, mixing, scaling, and bass management are handled internally in the STA333BWQS via RAM. Access to this RAM is available to the user via an I2C register interface. A collection of I2C registers are dedicated to this function. One contains a coefficient base address, five sets of three store the values of the 24-bit coefficients to be written or that were read, and one contains bits used to control the write/read of the coefficient(s) to/from RAM. Note: The read and write operation on RAM coefficients works only if LRCKI (pin 29) is switching. Reading a coefficient from RAM 1. 2. 3. 4. 5. Write 6-bits of address to I2C register 0x16. Write 1 to R1 bit in I2C address 0x26. Read top 8-bits of coefficient in I2C address 0x17. Read middle 8-bits of coefficient in I2C address 0x18. Read bottom 8-bits of coefficient in I2C address 0x19. Reading a set of coefficients from RAM 1. 2. 3. 4. 5. 6. 7. 8. 9. Write 6-bits of address to I2C register 0x16. Write 1 to RA bit in I2C address 0x26. Read top 8-bits of coefficient in I2C address 0x17. Read middle 8-bits of coefficient in I2C address 0x18. Read bottom 8-bits of coefficient in I2C address 0x19. Read top 8-bits of coefficient b2 in I2C address 0x1A. Read middle 8-bits of coefficient b2 in I2C address 0x1B. Read bottom 8-bits of coefficient b2 in I2C address 0x1C. Read top 8-bits of coefficient a1 in I2C address 0x1D. 10. Read middle 8-bits of coefficient a1 in I2C address 0x1E. 11. Read bottom 8-bits of coefficient a1 in I2C address 0x1F. 12. Read top 8-bits of coefficient a2 in I2C address 0x20. 13. Read middle 8-bits of coefficient a2 in I2C address 0x21. 14. Read bottom 8-bits of coefficient a2 in I2C address 0x22. 15. Read top 8-bits of coefficient b0 in I2C address 0x23. 16. Read middle 8-bits of coefficient b0 in I2C address 0x24. 17. Read bottom 8-bits of coefficient b0 in I2C address 0x25. 55/71 Register description STA333BWQS Writing a single coefficient to RAM 1. 2. 3. 4. 5. Write 6-bits of address to I2C register 0x16. Write top 8-bits of coefficient in I2C address 0x17. Write middle 8-bits of coefficient in I2C address 0x18. Write bottom 8-bits of coefficient in I2C address 0x19. Write 1 to W1 bit in I2C address 0x26. Writing a set of coefficients to RAM 1. 2. 3. 4. 5. 6. 7. 8. 9. Write 6-bits of starting address to I2C register 0x16. Write top 8-bits of coefficient b1 in I2C address 0x17. Write middle 8-bits of coefficient b1 in I2C address 0x18. Write bottom 8-bits of coefficient b1 in I2C address 0x19. Write top 8-bits of coefficient b2 in I2C address 0x1A. Write middle 8-bits of coefficient b2 in I2C address 0x1B. Write bottom 8-bits of coefficient b2 in I2C address 0x1C. Write top 8-bits of coefficient a1 in I2C address 0x1D. Write middle 8-bits of coefficient a1 in I2C address 0x1E. 10. Write bottom 8-bits of coefficient a1 in I2C address 0x1F. 11. Write top 8-bits of coefficient a2 in I2C address 0x20. 12. Write middle 8-bits of coefficient a2 in I2C address 0x21. 13. Write bottom 8-bits of coefficient a2 in I2C address 0x22. 14. Write top 8-bits of coefficient b0 in I2C address 0x23. 15. Write middle 8-bits of coefficient b0 in I2C address 0x24. 16. Write bottom 8-bits of coefficient b0 in I2C address 0x25. 17. Write 1 to WA bit in I2C address 0x26. The mechanism for writing a set of coefficients to RAM provides a method of updating the five coefficients corresponding to a given biquad (filter) simultaneously to avoid possible unpleasant acoustic side-effects. When using this technique, the 6-bit address specifies the address of the biquad b1 coefficient (for example, 0, 5, 10, 20, 35 decimal), and the STA333BWQS generates the RAM addresses as offsets from this base value to write the complete set of coefficient data. 6.12.18 User-defined EQ The STA333BWQS provides the ability to specify four EQ filters (biquads) per each of the two input channels. The biquads use the following equation: Y[n] = 2(b0/2)X[n] + 2(b1/2)X[n-1] + b2X[n-2] to 2(a1/2)Y[n-1] - a2Y[n-2] = b0X[n] + b1X[n-1] + b2X[n-2] - a1Y[n-1] - a2Y[n-2] where Y[n] represents the output and X[n] represents the input. Multipliers are 24-bit signed fractional multipliers, with coefficient values in the range of 0x800000 (-1) to 0x7FFFFF (0.9999998808). 56/71 STA333BWQS Register description Coefficients stored in the User Defined Coefficient RAM are referenced in the following manner: CxHy0 = b1/2 CxHy1 = b2 CxHy2 = -a1/2 CxHy3 = -a2 CxHy4 = b0/2 where x represents the channel and the y the biquad number. For example C2H41 is the b2 coefficient in the fourth biquad for channel 2. Additionally, the STA333BWQS allows specification of a high-pass filter (processing channels 1 and 2) and a lo-pass filter (processing channel 3) to be used for bass-management crossover when the XO setting is 000 (user-defined). Both of these filters when defined by the user (rather than using the preset crossover filters) are second order filters that use the biquad equation noted above. They are loaded into the C12H0-4 and C3Hy0-4 areas of RAM noted in Table 69. By default, all user-defined filters are pass-through where all coefficients are set to 0, except the b0/2 coefficient which is set to 0x400000 (representing 0.5) 6.12.19 Pre-scale The STA333BWQS provides a multiplication for each input channel for the purpose of scaling the input prior to EQ. This pre-EQ scaling is accomplished by using a 24-bit signed fractional multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. The scale factor for this multiply is loaded into RAM using the same I2C registers as the biquad coefficients and the bass-management. All channels can use the channel 1 pre-scale factor by setting the Biquad link bit. By default, all pre-scale factors are set to 0x7FFFFF. 6.12.20 Post-scale The STA333BWQS provides one additional multiplication after the last interpolation stage and the distortion compensation on each channel. This post-scaling is accomplished by using a 24-bit signed fractional multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. The scale factor for this multiply is loaded into RAM using the same I2C registers as the biquad coefficients and the bass-management. This post-scale factor can be used in conjunction with an ADC equipped micro-controller to perform power-supply error correction. All channels can use the channel 1 post-scale factor by setting the post-scale link bit. By default, all post-scale factors are set to 0x7FFFFF. When Line output is being utilized, channel 3 post-scale will affect both channels 3 and 4. 6.12.21 Over-current post-scale The STA333BWQS provides a simple mechanism for reacting to over-current detection in the power-block. When the ocwarn input is asserted, the over-current post-scale value is used in place of the normal post-scale value to provide output attenuation on all channels. The default setting provides 3 dB of output attenuation when ocwarn is asserted. The amount of attenuation to be applied in this situation can be adjusted by modifying the Over-current Post-scale value. As with the normal post-scale, this scaling value is a 24-bit signed fractional multiplier, with 0x800000 = -1 and 0x7FFFFF = 0.9999998808. By default, 57/71 Register description STA333BWQS the over-current post-scale factor is set to 0x5A9DF7. Once the over-current attenuation is applied, it remains until the device is reset. Table 69. RAM block for biquads, mixing, scaling, bass management Coefficient C1H10(b1/2) C1H11(b2) Channel 1, Biquad 1 C1H12(a1/2) C1H13(a2) C1H14(b0/2) Channel 1, Biquad 2 ... Channel 1, Biquad 4 Channel 2, Biquad 1 0x15 ... 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C Channel 1, Pre-Scale Channel 2, Pre-Scale Channel 1, Post-Scale Channel 2, Post-Scale Channel 3, Post-Scale TWARN/OC- Limit Channel 1, Mix 1 Channel 1, Mix 2 Channel 2, Mix 1 Channel 2, Mix 2 Channel 3, Mix 1 Lo-Pass 2nd Order Filter for XO=000 Hi-Pass 2nd Order Filter for XO=000 ... Channel 2, Biquad 4 C2H11 ... C2H44 C12H0(b1/2) C12H1(b2) C12H2(a1/2) C12H3(a2) C12H4(b0/2) C3H0(b1/2) C3H1(b2) C3H2(a1/2) C3H3(a2) C3H4(b0/2) C1PreS C2PreS C1PstS C2PstS C3PstS TWOCL C1MX1 C1MX2 C2MX1 C2MX2 C3MX1 0x000000 ... 0x400000 0x000000 0x000000 0x000000 0x000000 0x400000 0x000000 0x000000 0x000000 0x000000 0x400000 0x7FFFFF 0x7FFFFF 0x7FFFFF 0x7FFFFF 0x7FFFFF 0x5A9DF7 0x7FFFFF 0x000000 0x000000 0x7FFFFF 0x400000 C1H20 ... C1H44 C2H10 Default 0x000000 0x000000 0x000000 0x000000 0x400000 0x000000 ... 0x400000 0x000000 Index (Hex) 0x00 0x01 0x02 0x03 0x04 0x05 ... 0x13 0x14 58/71 STA333BWQS Table 69. Register description RAM block for biquads, mixing, scaling, bass management (continued) Coefficient Channel 3, Mix 2 UNUSED UNUSED C3MX2 Default 0x400000 Index (Hex) 0x3D 0x3E 0x3F 6.13 Variable max power correction registers (0x27 to 0x28) MPCC bits determine the 16 MSBs of the MPC compensation coefficient. This coefficient is used in place of the default coefficient when MPCV = 1. D7 MPCC15 0 D7 MPCC7 1 D6 MPCC14 0 D6 MPCC6 1 D5 MPCC13 0 D5 MPCC5 0 D4 MPCC12 1 D4 MPCC4 0 D3 MPCC11 1 D3 MPCC3 0 D2 MPCC10 0 D2 MPCC2 0 D1 MPCC9 1 D1 MPCC1 0 D0 MPCC8 0 D0 MPCC0 0 6.14 Variable distortion compensation registers (0x29 to 0x2A) DCC bits determine the 16 MSBs of the distortion compensation coefficient. This coefficient is used in place of the default coefficient when DCCV = 1. D7 DCC15 1 D7 DCC7 0 D6 DCC14 1 D6 DCC6 0 D5 DCC13 1 D5 DCC5 1 D4 DCC12 1 D4 DCC4 1 D3 DCC11 0 D3 DCC3 0 D2 DCC10 0 D2 DCC2 0 D1 DCC9 1 D1 DCC1 1 D0 DCC8 1 D0 DCC0 1 6.15 Fault detect recovery constant registers (0x2B to 0x2C) FDRC bits specify the 16-bit fault detect recovery time delay. When FAULT is asserted, the TRISTATE output is immediately asserted low and held low for the time period specified by this constant. A constant value of 0x0001 in this register is ~.083 ms. The default value of 0x000C specifies ~.1 mS. D7 FDRC15 0 D7 FDRC7 0 D6 FDRC14 0 D6 FDRC6 0 D5 FDRC13 0 D5 FDRC5 0 D4 FDRC12 0 D4 FDRC4 0 D3 FDRC11 0 D3 FDRC3 1 D2 FDRC10 0 D2 FDRC2 1 D1 FDRC9 0 D1 FDRC1 0 D0 FDRC8 0 D0 FDRC0 0 59/71 Register description STA333BWQS 6.16 Device status register (0x2D) D7 PLLUL D6 FAULT D5 UVFAULT D4 OVFAULT D3 OCFAULT D2 OCWARN D1 TFAULT D0 TWARN This read-only register provides fault and thermal-warning status information from the power control block. Logic value 1 for faults or warning means normal state. Logic 0 means a fault or warning detected on power bridge. The PLLUL='1' means that the PLL is not locked. " " " " " " " " PLLUL: 0 = PLL locked, 1= PLL not locked. FAULT: 0 = fault detected on power bridge, 1 = normal operation UVFAULT: 0 = VCC1, VCC2 internally detected < under-voltage threshold. OVFAULT: 0 = VCC1, VCC2 internally detected > over-voltage threshold. OCFAULT: 0 = over-current fault detected OCWARN: 0 = over-current warning. TFAULT: 0 = thermal fault, junction temperature over-limit detection. TWARN: 0 = thermal warning, junction temperature is close to the fault condition. 60/71 STA333BWQS Application 7 7.1 Application Application scheme for power supplies Here in the next figure the typical application scheme for STA333BWQS concerning the power supplies. A particular care has to be devoted to the layout of the PCB. In particular the 3.3 resistors on the digital supplies (VDD_DIG) have to be put as close as possible to the device. This is to avoid any unwanted oscillation on the digital portion of the device due to the PCB track inductance. The same rule must also be applied to all the decoulpling capacitors in order to limit any kind of voltage spikes on all the supplies. Figure 18. Application scheme for power supplies 3R3 1 2 3 4 100nF 1uF 35V OUT2B 5 6 7 8 100nF 100nF OUT2A VCC OUT1B 9 10 11 12 1uF 35V OUT1A 100nF 13 14 15 16 DDX3B DDX3A 17 18 1000uF 35V + + + + GND_SUB SA TEST_MODE VSS VCC_REG OUT2B GND2 VCC2 OUT2A OUT1B VCC1 GND1 OUT1A GND_REG VDD CONFIG DDX3B DDX3A VDD_DIG GND_DIG SCL SDA INT_LINE RESET SDI LRCKI BICKI XTI PLL_GND FILTER_PLL VDD_PLL PWRDN GND_DIG VDD_DIG TWARN/4A EAPD/4B 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 3R3 TW EAPD 100nF PWDN GND_DIG 3V3 100nF 3V3 SCL SDA INTL GND_DIG 10K RESET DATA LRCKI BICKI XTI BEAD GND_DIG 1nF RESET PLL_FILT 100nF BEAD PLL_GND GND_DIG 3V3 3V3 7.2 PLL filter schematic It is recommended to use the below scheme and values for the PLL loop filter to achieve the best performances from the device in general application. Please be noted that the ground of this filter scheme has to be conncted to the ground of the PLL without any resistive path. Concerning the component values, please take into acount that the greater is the filter bandwidth, the less is the lock time but the higher is the PLL output jitter. Figure 19. PLL application scheme. FILTER_PLL 2K2 680pF 4.7nF BEAD 100pF GND_DIG PLL_GND 61/71 Application STA333BWQS 7.3 Typical output configuration Here after the typical output configuration used for BTL stereo mode. Please refer to the application note for all the other possible output configuration recommended schematics. Figure 20. Output configuration for stereo BTL mode 22uH OUT1A 100nF 6.2 22 100nF 470nF 100nF LEFT 330pF 6.2 100nF OUT1B 22uH 22uH OUT2A 100nF 6.2 22 100nF 470nF 100nF RIGHT 330pF 6.2 100nF OUT2B 22uH 62/71 STA333BWQS Characterization data 8 Characterization data Figure 21. Output power (for 1% THD) 30 25 4 ohm 6 ohm output power W 20 15 8 ohm 10 5 0 5 7 9 11 13 15 16 ohm 17 19 supply voltage V Figure 22. FFT 0 dBfs (1 kHz, 12 V, 8 ohm) +10 +0 -10 -20 -30 -40 -50 d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 20 50 100 200 500 1k 2k 5k 10k 20k Hz 63/71 Characterization data Figure 23. FFT -60 dBfs (1 kHz, 12 V, 8 ohm) +10 +0 -10 -20 -30 -40 -50 STA333BWQS d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 24. THD vs. Freq (12 V Vcc 1 W output) 1 0.5 4ohm 0.2 6ohm % 0.1 0.05 0.02 8ohm 0.01 20 50 100 200 500 1k 2k 5k 10k 20k Hz 64/71 STA333BWQS Figure 25. FFT 0 dBfs (1 kHz, 18 V, 8 ohm) +10 +0 -10 -20 -30 -40 -50 Characterization data d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 26. FFT -60 dBfs (1 kHz, 18 V, 8 ohm) +10 +0 -10 -20 -30 -40 -50 d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 27. THD vs. Freq (18 V Vcc, 1 W output) 1 0.5 6ohm 0.2 4ohm 0.1 % 0.05 0.02 8ohm 0.01 20 50 100 200 500 1k 2k 5k 10k 20k Hz 65/71 Package thermal characteristics STA333BWQS 9 Package thermal characteristics Using a double-layer PCB the thermal resistance junction to ambient with 2 copper ground area of 3x3 cm and with 16 via holes (see Figure 28) is 24 C/W in natural air convection. The dissipated power within the device depends primarily on the supply voltage, load impedance and output modulation level. The estimated maximum dissipated power for the STA333BWQS is: 2 x 20 W into 8 , 18 V 2 x 10 W + 1 x 20 W into 4 , 8 , 18 V Pd max ~ 4 W Pd max < 5 W Figure 28. Double layer PCB with 16 via holes Figure 29 shows the power derating curve for the PowerSSO-36 package on a board with two different sizes of copper layers. Figure 29. PowerSSO-36 power derating curve Pd (W) 8 7 6 5 4 3 2 1 0 0 20 40 60 80 100 120 140 160 Tamb ( C) Copper Area 2x2 cm and via holes Copper Area 3x3 cm and via holes STA333BW STA333BWQS PowerSSO-36 PSSO36 66/71 STA333BWQS Package information 10 Package information In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 30. PowerSSO-36 (slug-up) mechanical data and package dimensions DIM. A A2 a1 b c D (1) E (1) e e3 F G G1 H h k L M N O Q S T U X Y MIN. 2.15 2.15 0 0.18 0.23 10.10 7.4 0.5 8.5 2.3 0.10 0.06 10.50 0.40 5 0.55 4.3 10 1.2 0.8 2.9 3.65 1.0 4.1 6.5 4.7 7.3 0.161 0.256 0.047 0.031 0.114 0.144 0.039 0.185 0.287 0.90 0.022 0.169 10 mm TYP. MAX. 2.47 2.40 0.075 0.36 0.32 10.50 7.6 MIN. 0.084 0.084 0 0.007 0.009 0.398 0.291 0.019 0.335 0.090 0.004 0.002 0.413 0.016 5 0.035 inch TYP. MAX. 0.097 0.094 0.003 0.014 0.012 0.413 0.299 OUTLINE AND MECHANICAL DATA 10.10 0.398 PowerSSO-36 (slug-down) (1) "D" and "E" do not include mold flash or protrusions Mold flash or protrusions shall not exceed 0.15 mm per side(0.006") A2 A hx45u G LEAD COPLANARITY A D e stand-off a1 T Y M Gauge plane 0.25 L O E H F U B 0.1 M A B b e3 S BOTTOM VIEW X 7587131 A k c Q 67/71 License information STA333BWQS 11 License information Supply of this product does not convey a license under the relevant intellectual property of the companies mentioned in this chapter nor imply any right to use this intellectual property in any finished end-user or ready to use final product. An independent license for such use is required and can be obtained by contacting the company or companies concerned. Once the license is obtained, a copy must be sent to STMicroelectronics. The details of all the features requiring licenses are not provided within the datasheet and register manual. They are provided only after a copy of the license has been received by STMicroelectronics. The feature requiring license is: QXpander(R), QHD(R) QHD(R) and QXpander(R) are intellectual property of QSound Labs Inc. A license can be obtained with the STA333BWQS via STMicroelectronics,please contact the HPC Audio Division Product Manager for details. Alternatively the license can be obtained directly from QSound Labs Inc. For details please contact: sales@qsound.com or QSound Labs, Inc 400 - 3115 12th Street NE Calgary, AB Canada T2E 7J2 68/71 STA333BWQS Trademarks and other acknowledgements 12 Trademarks and other acknowledgements DDX is a registered trademark of Apogee Technology Inc. SoundTerminal is a trademark of STMicroelectronics. ECOPACK is a registered trademark of STMicroelectronics. QHD and QXpander are registered trademarks of QSound Labs Inc. 69/71 Revision history STA333BWQS 13 Revision history Table 70. Date 27-Mar-2008 Document revision history Revision 1 Initial release Changes 70/71 STA333BWQS Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 71/71 |
Price & Availability of STA333BWQS13TR |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |