 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Full Color Chip LEDs 15-23B/R6G6BHC-A01/2T Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Full-color type. Descriptions The 15-23B SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Chip Type R6 G6 BH Material AlGaInP InGaN InGaN Emitted Color Brilliant Red Brilliant Yellow Green Water Clear Lens Color Blue Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 1 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Package Outline Dimensions Notes: Tolerances Unless Dimension 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 2 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Absolute Maximum Ratings (Ta=25) Parameter Reverse Voltage Symbol VR Rating 5 R6:25 Forward Current IF G6:25 BH:25 Operating Temperature Storage Temperature Soldering Temperature Topr Tstg Tsol -40 ~ +85 -40 ~ +90 260 (for 5 seconds) R6:2000 Electrostatic Discharge ESD G6:150 BH:150 R6:60 Power Dissipation Pd G6:110 BH:110 Peak Forward Current (Duty 1/10 @1KHz) R6:60 IF P G6:100 BH:100 mA mW V mA Unit V Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 3 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Electro-Optical Characteristics (Ta=25) Parameter Symbol R6 Min. Typ. Max. Unit Condition Luminous Intensity Iv G6 BH 72 28.5 28.5 --------619 568 465 100 50 50 120 632 575 468 ----- 180 90 90 --------629 575 480 mcd Viewing Angle 21/2 R6 deg Peak Wavelength p G6 BH R6 nm Dominant Wavelength d G6 BH R6 nm IF=20mA 20 ----20 25 ----2.0 2.0 3.5 ----2.4 2.4 3.9 10 10 50 V Spectrum Radiation Bandwidth G6 BH R6 ----- nm Forward Voltage VF G6 BH R6 Reverse Current IR G6 BH ----- A VR=5V Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.1V Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 4 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Typical Electro-Optical Characteristics Curves R6 Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 5 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Typical Electro-Optical Characteristics Curves G6 Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 6 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Typical Electro-Optical Characteristics Curves BH Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 7 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 8 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 9 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% No. 1 Items Reflow Soldering Test Condition Temp. : 2405 5sec. H : +100 15min 5 min L : -40 15min H : +100 5min 10 sec L : -10 5min Temp. : 100 Temp. : -40 IF = 20 mA 85/R.H85% Test Sample Ac/Re Hours/Cycles Size 6 Min. 22 PCS. 0/1 2 Temperature Cycle 300 Cycles 22 PCS. 0/1 3 Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity 300 Cycles 22 PCS. 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs. 0/1 4 5 6 7 22 PCS. 22 PCS. 22 PCS. 22 PCS. 0/1 0/1 0/1 0/1 Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 10 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Lead solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 11 of 12 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. ReliabilityLane 76,Items And Conditions Office: No 25, Test Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com The Tucheng, Taipei 236, Taiwan, R.O.C be satisfied with items listed below. reliability of products shall EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936 Everlight Electronics Co., Ltd. Device No:DSE-153- http://www.everlight.com Prepared date: 09-08-2003 Rev 1.0 Page: 12 of 12 Prepared by: Jeff Tsai |
Price & Availability of R6G6BHC-A01
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |