|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
RH119 High Performance Dual Comparator DESCRIPTION The RH119 dual comparator features low input offset voltage and offset current, high voltage gain, guaranteed common mode rejection and input protection diodes. The RH119 is capable of operation over a supply range from 5V to 15V and can drive 25mV leads from each open collector output. A separate GND pin allows the RH119 to isolate system grounds. The wafer lots are processed to Linear Technology's inhouse Class S flow to yield circuits usable in stringent military applications. , LTC and LT are registered trademarks of Linear Technology Corporation. ABSOLUTE MAXIMUM RATINGS Supply Voltage ........................................................ 36V Output to Negative Supply Voltage ......................... 36V Ground to Negative Supply Voltage ........................ 25V Ground to Positive Supply Voltage ......................... 18V Diffierential Input Voltage ....................................... 5V Differential Input Current ...................................... 5mA Input Voltage (See Note 1) Output Short-Circuit Duration ............................. 10 sec Operating Temperature Range .............. - 55C to 125C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C BUR -I CIRCUIT 10k 18V TO 20V - + 100 V+ SIDE 1 GND1 OUT1 10k - SIDE 2 10k OUT2 GND2 V- + RH119 BI -18V TO -20V PACKAGE I FOR ATIO TOP VIEW V+ OUT1 1 GND1 2 +IN1 3 -IN1 4 5 10 9 -IN2 8 +IN2 7 GND2 6 OUT2 NC NC GND1 +IN1 -IN1 V- OUT2 TOP VIEW TOP VIEW 1 2 3 4 5 6 7 J PACKAGE 14-LEAD CERDIP 14 NC 13 NC 12 OUT1 11 V+ OUT1 GND1 +IN1 -IN1 V- 1 2 3 4 5 10 9 8 7 6 V+ -IN2 +IN2 GND2 OUT2 10 -IN2 9 8 +IN2 GND2 V- H PACKAGE 10-LEAD TO-5 METAL CAN W PACKAGE 10-LEAD CERPAC U WW W U W U U UU 1 RH119 TABLE 1: ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER VOS CMRR IOS IB AV tR VSAT Input Offset Voltage Common Mode Rejection Ratio Input Offset Current Input Bias Current Voltage Gain Response Time Saturation Voltage VIN V+ VIN - 5mV, IO = 25mA 4.5V, - 6mV, ISINK 3.2mA TA 0C TA 0C V - = 0V 4 10 80 200 1.5 3 CONDITIONS VS = 15V, VCM = 0V 3 90 75 500 1 1 1 4 4 1 200 5,6 100 1000 2,3 2,3 NOTES (Preirradiation) (Note 2) TJ = 25C TYP MAX 4 SUB- - 55C T AJ 125C SUBGROUP MIN TYP MAX GROUP 1 7 2,3 MIN UNITS mV mV dB nA nA V/mV ns V 0.4 2 - 12 1 12 3 5 1 1 1 1 1 - 12 1 0.4 0.6 10 12 3 5 2 3 2,3 2,3 2,3 2.3 V V A V V V mA Output Leakage Current Input Voltage Range Differential Input Voltage IS Supply Current Positive Supply Current Negative Supply Current VIN 5mV, V OUT = 35V VS = 15V V + = 5V, V - = 0V V + = 5V, V - = 0V VS = 15V VS = 1 5V 4.3 11.5 4.5 1 1 mA mA TABLE 1A: ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER VOS IOS IB AVOL VSAT Offset Voltage Input Offset Current Input Bias Current Large-Signal Voltage Gain Saturation Voltage VIN V+ - 5mV, IO = 25mA V - = 0V 3 3 10 CONDITIONS (Postirradiation) (Note 5) 50Krad(Si) 100Krad(Si) 200Krad(Si) MIN MAX MIN MAX MIN MAX UNITS 4 150 1000 10 1.5 0.4 1.5 0.4 10 1.5 0.4 4 300 1500 5 1.5 0.4 8 500 2000 mV nA nA V/mV V V 10Krad(Si) 20Krad(Si) NOTES MIN MAX MIN MAX 4 75 500 10 1.5 0.4 4 100 750 4.5V, VIN -6mV, ISINK 3.2mA CMRR IS Common Mode Rejection Ratio Positive Supply Current Negative Supply Current Output Leakage Current VS = 15V VS = 15V 90 11.5 4.5 2 90 11.5 4.5 2 90 11.5 4.5 2 90 11.5 4.5 2 90 11.5 4.5 2 dB mA mA A VIN 5mV, V OUT 35V 2 RH119 ELECTRICAL CHARACTERISTICS (Continued) Note 3: The offset voltages and currents given are the maximum values required to drive the output within 1V of either supply with a 1mA load-- thus, these parameters define an error band and take into account the worst-case effects of voltage gain and input impedance. Note 4: Response time specified for a 100mV input step with 5mV overdrive. Note 5: VS = 15V, VCM = 0V, TA = 25C unless otherwise noted. Note 1: For supply voltages less than 15V, the maximum input voltage is equal to the supply voltage. Note 2: Unless otherwise noted, supply voltage equals 15V and TA = 25C. The GND pin is grounded. Note that the maximum voltage allowed between the GND pin and V + is 18V. Do not tie the GND pin to V - when the power supply voltage exceeds 9V. The offset voltage, offset current and bias current specifications apply for all supply voltages between 15V and 5V unless otherwise specified. TABLE 2: ELECTRICAL TEST REQUIRE E TS MIL-STD-883 TEST REQUIREMENTS Final Electrical Test Requirements (Method 5004) Group A Test Requirements (Method 5005) Group C and D End Point Electrical Parameters (Method 5005) * PDA Applies to subgroup 1. See PDA Test Notes. SUBGROUP 1*,2,3,4 1,2,3,4 1 PDA Test Notes The PDA is specified as 5% based on failures from group A, subgroup 1, tests after cooldown as the final electrical test in accordance with method 5004 of MIL-STD-883 Class B. The verified failures (including Delta parameters) of group A, subgroup 1, after burn-in divided by the total number of devices submitted for burn-in in that lot shall be used to determine the percent for the lot. Linear Technology Corporation reserves the right to test to tighter limits than those given. TOTAL DOSE BIAS CIRCUIT 15V 10k V+ SIDE 1 OUT1 10k 10k - + 100 GND1 - SIDE 2 OUT2 GND2 V- + 10k -15V Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. UW RH119 TDBC 3 RH119 TYPICAL PERFORMANCE CHARACTERISTICS Input Offset Voltage 6 4 2 0 -2 -4 -6 V S = 15V VCM = 0V RS = 5k 2000 V S = 15V VCM = 0V INPUT OFFSET VOLTAGE (mV) INPUT BIAS CURRENT (nA) 1600 INPUT OFFSET CURRENT (nA) 1 10 100 TOTAL DOSE KRAD (Si) Open-Loop Gain 70 150 COMMON MODE REJECTION RATIO (dB) V S = 15V 60 OPEN-LOOP GAIN (V/mV) INPUT OFFSET VOLTAGE (mV) 50 40 30 20 10 1 10 100 TOTAL DOSE KRAD (Si) 4 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977 UW RH119 G01 RH119 G04 Input Bias Current 500 400 300 200 100 0 Input Offset Current V S = 15V VCM = 0V 1200 800 400 0 1000 1 10 100 TOTAL DOSE KRAD (Si) 1000 RH119 G02 -100 1 10 100 TOTAL DOSE KRAD (Si) 1000 RH119 G03 Common Mode Rejection Ratio 6 V S = 15V 140 130 120 110 100 90 4 2 0 -2 -4 -6 Input Offset Voltage V S = 15V RS = 50 1000 1 10 100 TOTAL DOSE KRAD (Si) 1000 RH119 G05 1 10 100 TOTAL DOSE KRAD (Si) 1000 RH119 G06 I.D. No. 66-10-0176 Rev. A 0896 LT/HP 0896 REV A 500 * PRINTED IN USA (c) LINEAR TECHNOLOGY CORPORATION 1990 |
Price & Availability of RH119 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |