View PSP-500-5_1297901.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TOTAL POWER INT'L
500W with PFC and Parallel Function
Features :
PSP-500
series
Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage/Over temperature Foced air cooling by built-in DC fan Current sharing up to 2000W(3+1) With power good and fail signal output Built-in remote ON-OFF control Built-in remote sense function 3 years warranty
SPECIFICATION
MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER LOAD PSP-500-5 5V 80A 0 ~ 80A 400W PSP-500-12 12V 41.5A 0 ~ 41.5A 498W 150mVp-p 10 ~ 13.2V 1.0% 0.3% 0.5% PSP-500-13.5 13.5V 37A 0 ~ 37A 499.5W 150mVp-p 12 ~ 15V 1.0% 0.3% 0.5% PSP-500-15 15V 33A 0 ~ 33A 495W 150mVp-p 13.5 ~ 18V 1.0% 0.3% 0.5% PSP-500-24 24V 20.8A 0 ~ 20.8A 499.2W 150mVp-p 20 ~ 26.4V 1.0% 0.2% 0.5% PSP-500-27 27V 18.5A 0 ~ 18.5A 499.5W 150mVp-p 24 ~ 30V 1.0% 0.2% 0.5% PSP-500-48 48V 10.5A 0 ~ 10.5A 504W 200mVp-p 41 ~ 56V 1.0% 0.2% 0.5%
RIPPLE & NOISE (max.) Note.2 100mVp-p
4.75 ~ 5.5V VOLTAGE TOLERANCE Note.3 2.0% 0.5% 2.0% 24ms at full load
Note.6 90 ~ 264VAC
1500ms, 50ms at full load 127 ~ 370VDC 0.98/100VAC at full load 82% 3.5A/230VAC 40A/230VAC 82% 82% 84% 84% 86%
47 ~ 63Hz 0.95/230VAC 76% 7A/115AVC 20A/115VAC <1mA / 240VAC 110 ~ 125% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V Protection type : Shut down o/p voltage, re-power on to recover RTH2 95 Detect on heatsink of Q1,Q7 power transistor & L3 output choke Protection type : Shut down o/p voltage, recovers automatically after temperature goes down RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off sink current <4 ~ 10mA -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH with 30CFM forced air non-condensing -20 ~ +85 0.03%/ , 10 ~ 95% RH (0 ~ 50
PROTECTION OVER VOLTAGE OVER TEMPERATURE
FUNCTION REMOTE CONTROL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved
WITHSTAND VOLTAGE
I/P-O/P:3KVAC
I/P-FG:1.5KVAC
O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC
(Note 4)
HARMONIC CURRENT EMS IMMUNITY MTBF DIMENSION PACKING
Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 130.1K hrs min. MIL-HDBK-217F (25 278*129*63.5mm (L*W*H) 2.6Kg; 6pcs/15.7Kg/0.89CUFT )
OTHERS
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. In parallel connection, maybe only one unit operated, if the total output load less than 5% of rated load condition. 6. Derating may be needed under low input voltages. Please check the derating curve for more details.
500W with PFC and Parallel Function
Mechanical Specification
PSP-500
Case No. 919A
series
Unit:mm
220
4-M3
16
30
20
127 113
7
5
4-M3
4-M3
O/P
1 2 3 4 5 6
127
I/P
1 2 3
113
10
10
13
Air flow direction
51 62 73 84
7
7
LED
ADJ.
240 251 278
5
CONTROL
34.5 20 63.5
4-M3
240
220
15
BOTTOM VIEW
TOP VIEW
AC Input Terminal Pin. No. Assignment
Pin No. 1 2 3 Assignment AC/L AC/N FG
DC Output Terminal Pin. No Assignment
Pin No. 1~3 4~6 Assignment DC OUTPUT +V DC OUTPUT -V
Control Pin. No Assignment : MOLEX 5559-NP uses 5558 male crimp terminal
Pin No. Assignment Pin No. Assignment Mating connector Terminal 1 P(Current share) 5 NC MOLEX 5556 2 6 -S PF(Power fail signal) MOLEX 5557-NR Female crimp Terminal G +S 3 7 receptacle RCRC+ 4 8
Derating Curve
Output Derating VS Input Voltage
12 ~ 48V
100
100 90
80
80
60
5V
70
LOAD (%)
40
LOAD(%)
0 10 20 30 40 50 60
60 50 40
20
-10
90
115
135
180
230
264
AMBIENT TEMPERATURE ( )
INPUT VOLTAGE (V) 60Hz
File Name:PSP-500-SPEC 2005-09-13
500W with PFC and Parallel Function
Control terminal instruction manual
PF G +5V
PSP-500
series
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
-V -V -V +V +V +V LOAD + POWER SIGNAL
-V -V
-V +V +V +V LOAD +
-V -V -V +V +V +V
DC 0~15V
LOAD +
Power Fail Signal
PF Signal is the voltage difference between "G" and "PF" pin output
Remote Sensing
Remote Control
Power ON: When V RC+ , RC- =0 ~ 0.8V or Open Power OFF: When V RC+ , RC- =4 ~ 10V
Parallel Operation
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
-V -V -V +V +V +V
-V -V -V +V +V +V
-V -V -V +V +V +V
LOAD +
Parallel Operation With Remote Sensing
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
RC- RC+ G -S P +S PF NC
-V -V -V +V +V +V
-V -V -V +V +V +V
LOAD +
-V -V -V +V +V +V
DC 0~15V
Parallel Operation With Remote Control
500W with PFC and Parallel Function
Features :
PSP-500-P
Universal AC input / Full range Built-in active PFC function, PF>0.95
series
Protections:Short circuit/Over load/Over voltage/Over temperature Foced air cooling by built-in DC fan Current sharing up to 2000W(3+1) With power good and fail signal output Built-in remote ON-OFF control Built-in remote sense function 3 years warranty
SPECIFICATION
MODEL DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER OUTPUT VOLTAGE ADJ. RANGE PSP-500-5P 5V 80A 0 ~ 80A 400W PSP-500-12P 12V 41.5A 0 ~ 41.5A 498W 150mVp-p 10 ~ 13.2V 1.0% 0.3% 0.5% PSP-500-13.5P 13.5V 37A 0 ~ 37A 499.5W 150mVp-p 12 ~ 15V 1.0% 0.3% 0.5% PSP-500-15P 15V 33A 0 ~ 33A 495W 150mVp-p 13.5 ~ 18V 1.0% 0.3% 0.5% PSP-500-24P 24V 20.8A 0 ~ 20.8A 499.2W 150mVp-p 20 ~ 26.4V 1.0% 0.2% 0.5% PSP-500-27P 27V 18.5A 0 ~ 18.5A 499.5W 150mVp-p 24 ~ 30V 1.0% 0.2% 0.5% PSP-500-48P 48V 10.5A 0 ~ 10.5A 504W 200mVp-p 41 ~ 56V 1.0% 0.2% 0.5%
RIPPLE & NOISE (max.) Note.2 100mVp-p 4.75 ~ 5.5V VOLTAGE TOLERANCE Note.3 2.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE FUNCTION REMOTE CONTROL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 0.5% 2.0% 24ms at full load
Note.5 90 ~ 264VAC
1500ms, 50ms at full load 127 ~ 370VDC 0.98/100VAC at full load 82% 3.5A/230VAC 40A/230VAC 82% 82% 84% 84% 86%
47 ~ 63Hz 0.95/230VAC 76% 7A/115AVC 20A/115VAC <1mA / 240VAC 110 ~ 125% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V Protection type : Shut down o/p voltage, re-power on to recover RTH2 95 Detect on heatsink of Q1,Q7 power transistor & L3 output choke Protection type : Shut down o/p voltage, recovers automatically after temperature goes down RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH with 30CFM forced air non-condensing -20 ~ +85 0.03%/ , 10 ~ 95% RH (0 ~ 50 sink current <4 ~ 10mA
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL1950, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC
(Note 4)
HARMONIC CURRENT EMS IMMUNITY MTBF
Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 130.1K hrs min. MIL-HDBK-217F (25 ) 250*123*50mm (L*W*H) 1.3Kg; 6pcs/7.8Kg/0.89CUFT
OTHERS
DIMENSION PACKING
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details.
500W with PFC and Parallel Function
Mechanical Specification
250
PSP-500-P
series
Unit:mm
Air flow direction I/P 1
123
3
88
I/P
9.5
1 2 FS1 3 10A/250V CN1
12 7 CN2 1
SVR2 Io ADJ.
5 6
SVR1 Vo ADJ.
8
9.5
4
3.2
153
87
5
6-
AC Input Terminal Pin. No. Assignment
Pin No. 1 2 3 Assignment AC/L AC/N FG
Connector Pin. No. Assignment (CN1) : JST B2B-XH or equivalent
Pin No. 1 2 Assignment GND +12V Mating Housing JST XHP or equivalent Terminal JST SXH-001T-P0.6 or equivalent
Connector Pin. No. Assignment (CN2) : JST B7B-XH or equivalent
Pin No. Assignment 1 P(Current share) 2 +S 3 -S 4 GND Pin No. Assignment Mating Housing Terminal 5 Power fail signal JST SXH-001T-P0.6 JST XHP 6 RC+ or equivalent or equivalent 7 RC-
DC Output Terminal Pin. No Assignment
Pin No. 1~3 4~6 Assignment DC OUTPUT +V DC OUTPUT -V
Derating Curve
Output Derating VS Input Voltage
12 ~ 48V
100
100 90
80
80
60
5V
70
LOAD (%)
40
LOAD(%)
With 30CFM forced air
60 50 40
20
-10
0
10
20
30
40
50
60
90
115
135
176
230
50
264
AMBIENT TEMPERATURE ( )
INPUT VOLTAGE (V) 60Hz
5
113
2
8

▲Up To Search▲

Price & Availability of PSP-500-5

	To Download PSP-500-5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .