View ICS8735AM-21T_1253152.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
FEATURES
* 1 differential 3.3V LVPECL output pair, 1 differential feedback output pair * Differential CLK, nCLK input pair * CLK, nCLK pair can accept the following differential input levels: LVDS, LVPECL, LVHSTL, SSTL, HCSL * Output frequency range: 31.25MHz to 700MHz * Input frequency range: 31.25MHz to 700MHz * VCO range: 250MHz to 700MHz * Programmable dividers allow for the following output-to-input frequency ratios: 8:1, 4:1, 2:1, 1:1, 1:2, 1:4, 1:8 * External feedback for "zero delay" clock regeneration with configurable frequencies * Cycle-to-cycle jitter: 25ps (maximum) * Static phase offset: 50ps 100ps * 3.3V supply voltage * 0C to 70C ambient operating temperature * Industrial temperature information available upon request
GENERAL DESCRIPTION
The ICS8735-21 is a highly versatile 1:1 Differential-to-3.3V LVPECL clock generator and a HiPerClockSTM member of the HiPerClockSTMfamily of High Performance Clock Solutions from ICS. The CLK, nCLK pair can accept most standard differential input levels. The ICS8735-21 has a fully integrated PLL and can be configured as zero delay buffer, multiplier or divider, and has an output frequency range of 31.25MHz to 700MHz. The reference divider, feedback divider and output divider are each programmable, thereby allowing for the following output-to-input frequency ratios: 8:1, 4:1, 2:1, 1:1, 1:2, 1:4, 1:8. The external feedback allows the device to achieve "zero delay" between the input clock and the output clocks. The PLL_SEL pin can be used to bypass the PLL for system test and debug purposes. In bypass mode, the reference clock is routed around the PLL and into the internal output dividers.
ICS
BLOCK DIAGRAM
PLL_SEL
/1, /2, /4, /8, /16, /32, /64
PIN ASSIGNMENT
0 1 Q nQ QFB nQFB
CLK nCLK MR VCC nFB_IN FB_IN SEL2 VEE nQFB QFB 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 nc SEL1 SEL0 VCC PLL_SEL VCCA SEL3 VCCO Q nQ
CLK nCLK
PLL
8:1, 4:1, 2:1, 1:1, 1:2, 1:4, 1:8
FB_IN nFB_IN
ICS8735-21
20-Lead, 300-MIL SOIC 7.5mm x 12.8mm x 2.3mm body package M Package Top View
SEL0 SEL1 SEL2 SEL3 MR
8735AM-21
www.icst.com/products/hiperclocks.html
1
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
Type Description
TABLE 1. PIN DESCRIPTIONS
Number 1 2 3 4, 17 5 6 7 8 9, 10 11, 12 13 14 15 16 18 19 20 Name CLK nCLK MR VCC nFB_IN FB_IN SEL2 VEE nQFB, QFB nQ, Q VCCO SEL3 VCCA PLL_SEL S E L0 SEL1 nc Input Input Input Power Input Input Input Power Output Output Power Input Power Input Input Input Unused Pulldown Non-inver ting differential clock input. Inver ting differential clock input. Active HIGH Master Reset. When logic HIGH, the internal dividers are reset causing the true outpus Q to go low and the inver ted outputs nQ to go high. Pulldown When logic LOW, the internal dividers and the outputs are enabled. LVCMOS / LVTTL interface levels. Core supply pins. Feedback input to phase detector for regenerating clocks with "zero delay". Pullup Connect to pin 9. Feedback input to phase detector for regenerating clocks with "zero delay". Pulldown Connect to pin 10. Pulldown Determines output divider values in Table 3. LVCMOS / LVTTL interface levels. Pullup Negative supply pin. Differential feedback outputs. LVPECL interface levels. Differential clock outputs. LVPECL interface levels. Output supply pin. Pulldown Determines output divider values in Table 3. LVCMOS / LVTTL interface levels. Analog supply pin. Selects between the PLL and reference clock as the input to the dividers. Pullup When LOW, selects reference clock. When HIGH, selects PLL. LVCMOS / LVTTL interface levels. Pulldown Determines output divider values in Table 3. LVCMOS / LVTTL interface levels. Pulldown Determines output divider values in Table 3. LVCMOS / LVTTL interface levels. No connect.
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
TABLE 2. PIN CHARACTERISTICS
Symbol CIN RPULLUP RPULLDOWN Parameter Input Capacitance Input Pullup Resistor Input Pulldown Resistor Test Conditions Minimum Typical 4 51 51 Maximum Units pF K K
ICS8735AM-21
www.icst.com/products/hiperclocks.html
2
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
Outputs PLL_SEL = 1 PLL Enable Mode Q, nQ; QFB, nQFB /1 /1 /1 /1 /2 /2 /2 /4 /4 /8 x2 x2 x2 x4 x4 x8
TABLE 3A. CONTROL INPUT FUNCTION TABLE
Inputs SEL3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 SEL2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 S E L1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 SEL0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Reference Frequency Range (MHz)* 250 - 700 125 - 350 62.5 - 175 31.25 - 87.5 250 - 700 125 - 350 62.5 - 175 250 - 700 125 - 350 250 - 700 125 - 350 62.5 - 175 31.25 - 87.5 62.5 - 175 31.25 - 87.5 31.25 - 87.5
*NOTE: VCO frequency range for all configurations above is 250MHz to 700MHz.
TABLE 3B. PLL BYPASS FUNCTION TABLE
Inputs SEL3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
8735AM-21
SEL2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
S E L1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
SEL0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Outputs PLL_SEL = 0 PLL Bypass Mode Q, nQ; QFB, nQFB /4 /4 /4 /8 /8 /8 / 16 / 16 / 32 / 64 /2 /2 /4 /1 /2 /1
REV. D OCTOBER 27, 2003
www.icst.com/products/hiperclocks.html
3
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
4.6V -0.5V to VCC + 0.5V 50mA 100mA 46.2C/W (0 lfpm) -65C to 150C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC Inputs, VI Outputs, IO Continuous Current Surge Current Package Thermal Impedance, JA Storage Temperature, TSTG
TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C
Symbol Parameter VCC VCCA VCCO IEE ICCA Core Supply Voltage Analog Supply Voltage Output Supply Voltage Power Supply Current Analog Supply Current Test Conditions Minimum 3.135 3.135 3.135 Typical 3.3 3.3 3.3 Maximum 3.465 3.465 3.465 150 15 Units V V V mA mA
TABLE 4B. LVCMOS/LVTTL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C
Symbol Parameter VIH VIL IIH Input High Voltage Input Low Voltage Input High Current SEL0, SEL1, SEL2, SEL3, MR PLL_SEL SEL0, SEL1, SEL2, SEL3, MR PLL_SEL VCC = VIN = 3.465V VCC = VIN = 3.465V VCC = 3.465V, VIN = 0V VCC = 3.465V, VIN = 0V -5 -150 Test Conditions Minimum 2 -0.3 Typical Maximum VCC + 0.3 0.8 150 5 Units V V A A A A
IIL
Input Low Current
TABLE 4C. DIFFERENTIAL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C
Symbol Parameter IIH IIL V PP Input High Current Input Low Current CLK, FB_IN nCLK, nFB_IN CLK, FB_IN nCLK, nFB_IN Test Conditions VCC = VIN = 3.465V VCC = VIN = 3.465V VCC = 3.465V, VIN = 0V VCC = 3.465V, VIN = 0V -5 -150 0.15 1.3 VCC - 0.85 Minimum Typical Maximum 150 5 Units A A A A V V
Peak-to-Peak Input Voltage
Common Mode Input Voltage; NOTE 1, 2 VEE + 0.5 VCMR NOTE 1: Common mode voltage is defined as VIH. NOTE 2: For single ended applications, the maximum input voltage for CLK, nCLK is VCC + 0.3V.
ICS8735AM-21
www.icst.com/products/hiperclocks.html
4
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
Test Conditions Minimum VCCO - 1.4 VCCO - 2.0 0.6 Typical Maximum VCCO - 1.0 VCCO - 1.7 0.9 Units V V V
TABLE 4D. LVPECL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C
Symbol VOH VOL VSWING Parameter Output High Voltage; NOTE 1 Output Low Voltage; NOTE 1 Peak-to-Peak Output Voltage Swing
NOTE 1: Outputs terminated with 50 to VCCO - 2V.
TABLE 5. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C
Symbol fIN Parameter Input Frequency CLK, nCLK Test Conditions PLL_SEL = 1 PLL_SEL = 0 Minimum 31.25 Typical Maximum 700 700 Units MHz MHz
TABLE 6. AC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C
Symbol fMAX tPD tsk(o) t(O) t jit(cc) t jit() tL tR tF Parameter Output Frequency Propagation Delay; NOTE 1 Output Skew; NOTE 4, 5 Static Phase Offset; NOTE 2, 5 Cycle-to-Cycle Jitter; NOTE 5, 6 Phase Jitter; NOTE 3, 5, 6 PLL Lock Time Output Rise Time Output Fall Time 20% to 80% @ 50MHz 20% to 80% @ 50MHz 300 300 PLL_SEL = 0V, f 700MHz PLL_SEL = 0V PLL_SEL = 3.3V 3.0 Test Conditions Minimum Typical Maximum 700 4.2 20 150 25 50 1 700 700 Units MHz ns ps ps ps ps ms ps ps %
-50
50
odc Output Duty Cycle 47 53 All parameters measured at fMAX unless noted otherwise. NOTE 1: Measured from the differential input crossing point to the differential output crossing point. NOTE 2: Defined as the time difference between the input reference clock and the average feedback input signal, when the PLL is locked and the input reference frequency is stable. NOTE 3: Phase jitter is dependent on the input source used. NOTE 4: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at the output differential crosspoints. NOTE 5: This parameter is defined in accordance with JEDEC Standard 65. NOTE 6: Characterized at VCO frequency of 622MHz.
8735AM-21
www.icst.com/products/hiperclocks.html
5
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
PARAMETER MEASUREMENT INFORMATION
2V
VCC
VCC, VCCA, VCCO
Qx
SCOPE
nCLK
LVPECL
nQx
V EE
V
CLK
PP
Cross Points
V
CMR
-1.3V 0.165V
V EE
3.3V OUTPUT LOAD AC TEST CIRCUIT
DIFFERENTIAL INPUT LEVEL
nQx Qx nQy Qy
nQ, nQFB Q, QFB tCycle n
tJIT(cc) = tCycle n - tCycle n+1
tsk(o)
OUTPUT SKEW
nCLK CLK nFB_IN nFB_IN
CYCLE-TO-CYCLE JITTER
VOH VOL
nCLK
VOH
CLK
VOL t(O)
tjit(O) = t(O) -- t(O) mean = Phase Jitter t(O) mean = Static Phase Offset
(where t(O) is any random sample, and t(O) mean is the average of the sampled cycles measured on controlled edges)
nQ, nQFB Q, QFB
tPD
PHASE JITTER
nQ, nQFB Q, QFB
AND
STATIC PHASE OFFSET
PROPAGATION DELAY
80%
Pulse Width t
PERIOD
Clock Outputs
20% tR tF
odc =
t PW t PERIOD
OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD
ICS8735AM-21
OUTPUT RISE/FALL TIME
REV. D OCTOBER 27, 2003
www.icst.com/products/hiperclocks.html
6
tCycle n + 1
80% VSW I N G 20%
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR APPLICATION INFORMATION
POWER SUPPLY FILTERING TECHNIQUES
As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS8735-21 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. VCC, VCCA, and VCCO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 1 illustrates how a 10 resistor along with a 10F and a .01F bypass capacitor should be connected to each VCCA pin.
3.3V VCC .01F VCCA .01F 10 F 10
FIGURE 1. POWER SUPPLY FILTERING
WIRING THE DIFFERENTIAL INPUT TO ACCEPT SINGLE ENDED LEVELS
Figure 2 shows how the differential input can be wired to accept single ended levels. The reference voltage V_REF ~ VCC/2 is generated by the bias resistors R1, R2 and C1. This bias circuit should be located as close as possible to the input pin. The ratio
of R1 and R2 might need to be adjusted to position the V_REF in the center of the input voltage swing. For example, if the input clock swing is only 2.5V and VCC = 3.3V, V_REF should be 1.25V and R2/R1 = 0.609.
VDD
R1 1K Single Ended Clock Input CLK V_REF nCLK C1 0.1u
R2 1K
FIGURE 2. SINGLE ENDED SIGNAL DRIVING DIFFERENTIAL INPUT
8735AM-21
www.icst.com/products/hiperclocks.html
7
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
50 transmission lines. Matched impedance techniques should be used to maximize operating frequency and minimize signal distortion. Figures 3A and 3B show two different layouts which are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations.
TERMINATION
FOR
LVPECL OUTPUTS
The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources must be used for functionality. These outputs are designed to drive
3.3V
Zo = 50
125
FOUT FIN
125
Zo = 50
Zo = 50 50 1 Z ((VOH + VOL) / (VCC - 2)) - 2 o 50 VCC - 2V RTT
FOUT
FIN
Zo = 50 84 84
RTT =
FIGURE 3A. LVPECL OUTPUT TERMINATION
FIGURE 3B. LVPECL OUTPUT TERMINATION
SCHEMATIC EXAMPLE
Figure 4 shows a schematic example of the ICS8735-21. In this example, the input is driven by an HCSL driver. The zero delay buffer is configured to operate at 155.52MHz input and 77.75MHz output. The logic control pins are configured as follows:
SEL [3:0] = 0101; PLL_SEL = 1 The decoupling capacitors should be physically located near the power pin. For ICS8735-21.
3.3V
VCCA
U1
R7
Zo = 50 Ohm
VCC
(155.5 MHz)
VCC
SEL2
10
1 2 3 4 5 6 7 8 9 10
CLK nCLK MR VCCI nFB_IN FB_IN SEL2 VEE nQFB QFB nc SEL1 SEL0 VCCI PLL_SEL VCCA SEL3 VCCO Q nQ
Zo = 50 Ohm
HCSL
R8 50
VCC
R9 50
20 19 18 17 16 15 14 13 12 11
SEL1 SEL0 VCC PLL_SEL VCCA SEL3 VCC
C11 0.01u
C16 10u
Zo = 50 Ohm
+
Zo = 50 Ohm
R1 50
RU4 1K
RU5 SP
RU6 1K
R2 50
ICS8735-21
-
RU3 1K
RU7 SP
PLL_SEL SEL0 SEL1 SEL2 SEL3
(77.75 MHz)
R3 50
LVPECL_input
R4 50
R5 50
Bypass capacitors located near the power pins
(U1-4) VCC
(U1-17)
C2 0.1uF
R6 50
(U1-13)
C3 0.1uF
RD3 SP
RD4 SP
RD5 1K
RD6 SP
RD7 1K
VCC=3.3V
C1 0.1uF
SP = Space (i.e. not intstalled)
SEL[3:0] = 0101, Divide by 2
FIGURE 4. ICS8735-21 LVPECL BUFFER SCHEMATIC EXAMPLE
ICS8735AM-21
www.icst.com/products/hiperclocks.html
8
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
here are examples only. Please consult with the vendor of the driver component to confirm the driver termination requirements. For example in Figure 4A, the input termination applies for ICS HiPerClockS LVHSTL drivers. If you are using an LVHSTL driver from another vendor, use their termination recommendation.
DIFFERENTIAL CLOCK INPUT INTERFACE
The CLK /nCLK accepts LVDS, LVPECL, LVHSTL, SSTL, HCSL and other differential signals. Both VSWING and VOH must meet the VPP and VCMR input requirements. Figures 5A to 5D show interface examples for the HiPerClockS CLK/nCLK input driven by the most common driver types. The input interfaces suggested
3.3V 3.3V
3.3V 1.8V
Zo = 50 Ohm
Zo = 50 Ohm CLK Zo = 50 Ohm nCLK LVHSTL ICS HiPerClockS LVHSTL Driver R1 50 R2 50
R3 50 LVPECL Zo = 50 Ohm
CLK
nCLK
HiPerClockS Input
HiPerClockS Input
R1 50
R2 50
FIGURE 5A. HIPERCLOCKS CLK/nCLK INPUT DRIVEN ICS HIPERCLOCKS LVHSTL DRIVER
BY
FIGURE 5B. HIPERCLOCKS CLK/nCLK INPUT DRIVEN 3.3V LVPECL DRIVER
BY
3.3V 3.3V 3.3V R3 125 Zo = 50 Ohm CLK Zo = 50 Ohm nCLK LVPECL R1 84 R2 84 HiPerClockS Input R4 125
3.3V
3.3V
LVDS_Driv er
Zo = 50 Ohm
CLK
R1 100
Zo = 50 Ohm
nCLK
Receiv er
FIGURE 5C. HIPERCLOCKS CLK/nCLK INPUT DRIVEN 3.3V LVPECL DRIVER
BY
FIGURE 5D. HIPERCLOCKS CLK/nCLK INPUT DRIVEN 3.3V LVDS DRIVER
BY
8735AM-21
www.icst.com/products/hiperclocks.html
9
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR POWER CONSIDERATIONS
This section provides information on power dissipation and junction temperature for the ICS8735-21. Equations and example calculations are also provided.
1. Power Dissipation. The total power dissipation for the ICS8735-21 is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load.
* *
Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 150mA = 519.8mW Power (outputs)MAX = 30.2mW/Loaded Output pair If all outputs are loaded, the total power is 2 * 30.2mW = 60.4mW
Total Power_MAX (3.465V, with all outputs switching) = 519.8mW + 60.4mW = 580.2mW
2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for HiPerClockSTM devices is 125C.
The equation for Tj is as follows: Tj = JA * Pd_total + TA Tj = Junction Temperature JA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance JA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 39.7C/W per Table 7 below. Therefore, Tj for an ambient temperature of 70C with all outputs switching is: 70C + 0.580W * 39.7C/W = 93C. This is well below the limit of 125C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer).
TABLE 7. THERMAL RESISTANCE JA
FOR
20-PIN SOIC, FORCED CONVECTION
JA by Velocity (Linear Feet per Minute)
0
Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 83.2C/W 46.2C/W
200
65.7C/W 39.7C/W
500
57.5C/W 36.8C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
ICS8735AM-21
www.icst.com/products/hiperclocks.html
10
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
3. Calculations and Equations.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in Figure 6.
VCCO
Q1
VOUT RL 50 VCCO - 2V
FIGURE 6. LVPECL DRIVER CIRCUIT
AND
TERMINATION
To calculate worst case power dissipation into the load, use the following equations which assume a 50 load, and a termination voltage of V - 2V.
CCO
*
For logic high, VOUT = V (V
CCO_MAX
OH_MAX
=V
CCO_MAX
- 1.0V
-V
OH_MAX
) = 1.0V =V - 1.7V
*
For logic low, VOUT = V (V
CCO_MAX
OL_MAX
CCO_MAX
-V
OL_MAX
) = 1.7V
Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = [(V - (V - 2V))/R ] * (V
L
OH_MAX
CCO_MAX
CCO_MAX
-V
OH_MAX
) = [(2V - (V
CCO_MAX
-V
OH_MAX
))/R ] * (V
L
CCO_MAX
-V
OH_MAX
)=
[(2V - 1V)/50] * 1V = 20.0mW
Pd_L = [(V
OL_MAX
- (V
CCO_MAX
- 2V))/R ] * (V
L
CCO_MAX
-V
OL_MAX
) = [(2V - (V
CCO_MAX
-V
OL_MAX
))/R ] * (V
L
CCO_MAX
-V
OL_MAX
)=
[(2V - 1.7V)/50] * 1.7V = 10.2mW Total Power Dissipation per output pair = Pd_H + Pd_L = 30.2mW
8735AM-21
www.icst.com/products/hiperclocks.html
11
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR RELIABILITY INFORMATION
TABLE 8. JAVS. AIR FLOW TABLE
FOR
20 LEAD SOIC
JA by Velocity (Linear Feet per Minute)
0
Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 83.2C/W 46.2C/W
200
65.7C/W 39.7C/W
500
57.5C/W 36.8C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
TRANSISTOR COUNT
The transistor count for ICS8735-21 is: 2969
ICS8735AM-21
www.icst.com/products/hiperclocks.html
12
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
20 LEAD SOIC
PACKAGE OUTLINE - M SUFFIX
FOR
TABLE 9. PACKAGE DIMENSIONS
SYMBOL N A A1 A2 B C D E e H h L 10.00 0.25 0.40 0 -0.10 2.05 0.33 0.18 12.60 7.40 1.27 BASIC 10.65 0.75 1.27 8 Millimeters Minimum 20 2.65 -2.55 0.51 0.32 13.00 7.60 Maximum
Reference Document: JEDEC Publication 95, MS-013, MO-119
8735AM-21
www.icst.com/products/hiperclocks.html
13
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
Marking ICS8735AM-21 ICS8735AM-21 Package 20 Lead SOIC 20 Lead SOIC on Tape and Reel Count 38 per tube 1000 Temperature 0C to 70C 0C to 70C
TABLE 10. ORDERING INFORMATION
Part/Order Number ICS8735AM-21 ICS8735AM-21T
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. ICS8735AM-21
www.icst.com/products/hiperclocks.html
14
REV. D OCTOBER 27, 2003
Integrated Circuit Systems, Inc.
ICS8735-21
700MHZ, DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY CLOCK GENERATOR
REVISION HISTORY SHEET Description of Change Revised Block Diagram. Added Output Skew row at 20ps Max. Relabled PLL Reference Zero Delay to Static Phase Offset. Added Output Skew Diagram. Added note at bottom of the table. Added Note 6. Added Termination for LVPECL Outputs section Pin Description Table - revised MR description. 3.3V Output Load Test Circuit Diagram, revised VEE equation from "-1.3V 0.135V" to " -1.3V 0.165V". Revised Output Rise/Fall Time Diagram. Added Schematic Example section Pin Description table - revised MR and VCC descriptions. Power Supply table - revised VCC Parameter to correspond with pin description. Deleted Figure 8, "Clock Input Driven by LVPECL Driver w/AC Couple". AC Couple is not recommended for Zero Delay Buffers. Pin Characteristics Table - changed CIN from 4pF max. to 4pF typical. Absolute Maximum Ratings - revised Output rating. Updated Single Ended Signal Driving Differential Input Diagram. Updated LVPECL Output Termination Diagrams. Updated Schematic Example. Updated Differential Clock Input Interface drawings. AC Characteristics Table - modifed tPD min. limit from 3.6ns to 3.0ns and deleted the typical value. Date 10/31/01
Rev B
Table T6 T6 T3A T6 T2
B B
B
Page 1 5 5 7 3 5 10 2 6 8 8-9
11/20/01 6/3/02
8/19/02
B T1 T4A
10/17/02
B
2 4 9
2/03/03
T2
C
D
T6
2 4 7 8 8 9 5
10/13/03
10/27/03
8735AM-21
www.icst.com/products/hiperclocks.html
15
REV. D OCTOBER 27, 2003

▲Up To Search▲

Price & Availability of ICS8735AM-21T

	To Download ICS8735AM-21T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .