|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
MICROWAVE CORPORATION v00.0404 HMC449 Features Output Power: +10 dBm Wide Input Power Range: -4 to +6 dBm Fo Isolation: 34 dBc @ Fout= 30 GHz GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT Typical Applications The HMC449 is suitable for: * Pt to Pt & Multi-Pt Radios * VSAT Radios * Military EW, ECM, C I * Test Instrumentation 3 100 kHz SSB Phase Noise: -132 dBc/Hz Single Supply: 5V@ 50 mA Die Size: 1.10 mm x 1.20 mm x 0.1 mm 4 FREQ. MULTIPLIERS - CHIP * Space Functional Diagram General Description The HMC449 die is a x2 active broadband frequency multiplier chip utilizing GaAs PHEMT technology. When driven by a 0 dBm signal the multiplier provides +10 dBm typical output power from 28 to 32 GHz. The Fo and 3Fo isolations are >34 dBc and >17 dBc respectively at 30 GHz. The HMC449 is ideal for use in LO multiplier chains yielding a reduced parts count vs. traditional approaches. The low additive SSB Phase Noise of -132 dBc/Hz at 100 kHz offset helps maintain good system noise performance. All data is with the chip in a 50 ohm test fixture connected via 0.076mm x 0.0127mm (3mil x 0.5mil) ribbon bonds of minimal length 0.31mm (<12mils). Electrical Specifications, TA = +25 C, Vdd= 5.0V, 0 dBm Drive Level Parameter Frequency Range, Input Frequency Range, Output Output Power Fo Isolation (with respect to output level) Fout= 30 GHz 3Fo Isolation (with respect to output level) Fout= 30 GHz Input Return Loss Output Return Loss SSB Phase Noise (100 kHz Offset) Supply Current (Idd) 6 Min. Typ. 13.5 - 16.5 27 - 33 10 34 17 13 9 -132 50 Max. Units GHz GHz dBm dBc dBc dB dB dBc/Hz mA 4 - 34 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.0404 HMC449 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT Output Power vs. GaAs MMIC SUB-HARMONICALLY Output Power vs. Drive Level PUMPED MIXER 17 - 25 Temperature @ 0 dBm Drive Level 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 26 27 28 29 30 16 14 12 10 8 6 4 2 0 -2 -4 -6 -8 -10 -12 26 27 28 GHz OUTPUT POWER (dBm) OUTPUT POWER (dBm) +25 C +85 C -55 C -6 dBm -4 dBm -2 dBm 0 dBm +2 dBm +4 dBm +6 dBm 4 30 31 32 33 34 31 32 33 34 29 OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ 0 dBm Drive Level 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 26 27 28 29 30 Isolation @ 0 dBm Drive Level 15 10 OUTPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 -30 Fo 2Fo 3Fo Vdd=4.5V Vdd=5.0V Vdd=5.5V 31 32 33 34 26 27 28 29 30 31 32 33 34 OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) Pin vs. Pout @ 3 Frequencies 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -5 -4 -3 -2 -1 0 1 2 3 4 INPUT POWER (dBm) OUTPUT POWER (dBm) Fout=27 GHz Fout=30 GHz Fout=33 GHz 5 6 7 8 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 4 - 35 FREQ. MULTIPLIERS - CHIP OUTPUT POWER (dBm) MICROWAVE CORPORATION v00.0404 HMC449 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT Input Return Loss vs. Temperature 0 +25 C Output Return Loss vs. Temperature 0 OUTPUT RETURN LOSS (dB) +25 C INPUT RETURN LOSS (dB) -5 +85 C -55 C -5 +85 C -55 C -10 -10 4 FREQ. MULTIPLIERS - CHIP -15 -15 -20 13 13.5 14 14.5 15 15.5 16 16.5 17 FREQUENCY (GHz) -20 26 27 28 29 30 31 32 33 34 FREQUENCY (GHz) SSB Phase Noise Performance, Fout = 26.4 GHz, Pin = 0 dBm 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 2 10 SSB PHASE NOISE (dBc/Hz) 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) 4 - 36 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.0404 HMC449 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT Absolute Maximum Ratings RF Input (Vcc= +5V) Supply Voltage (Vdd) Channel Temperature Continuous Pdiss (T= 85 C) (derate 8.3 mW/C above 85 C) Thermal Resistance (junction to die bottom) Storage Temperature Operating Temperature +20 dBm +6.0 Vdc 175 C 744 mW Typical Supply Current vs. Vdd Vdd (Vdc) 4.5 5.0 5.5 Idd (mA) 49 50 51 121 C/W -65 to +150 C -55 to +85 C Note: Multiplier will operate over full voltage range shown above. 4 FREQ. MULTIPLIERS - CHIP Outline Drawing NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]. 2. DIE THICKNESS IS .004" 3. TYPICAL BOND PAD IS .004" SQUARE. 4. TYPICAL BOND SPACING IS .006" CENTER TO CENTER. 5. BOND PAD METALIZATION: GOLD 6. BACKSIDE METALIZATION: GOLD 7. BACKSIDE METAL IS GROUND. 8. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 4 - 37 MICROWAVE CORPORATION v00.0404 HMC449 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT Pad Description Pad Number Function Description Pin is AC coupled and matched to 50 Ohm from 13 - 16 GHz. Interface Schematic 1 RF IN 4 FREQ. MULTIPLIERS - CHIP 2, 3 Vdd Supply voltage 5V 0.5V. 4 RF OUT Pin is AC coupled and matched to 50 Ohm from 26 - 32 GHz. GND Die bottom must be connected to RF ground. Assembly Diagram 4 - 38 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.0404 HMC449 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 27 - 33 GHz OUTPUT Handling Precautions Follow these precautions to avoid permanent damage. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Static Sensitivity: Follow ESD precautions to protect against > 250V ESD strikes. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer's schedule. 4 FREQ. MULTIPLIERS - CHIP 4 - 39 Wire Bonding Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of 150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils). Mounting & Bonding Techniques for Millimeterwave GaAs MMICs The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). 3 mil Ribbon Bond 3 mil Ribbon Bond 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). Microstrip substrates should be brought as close to the die as possible in order to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12 mils) is recommended to minimize inductance on RF, LO & IF ports. An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer capacitor (mounted eutectically or by conductive epoxy) placed no further than 0.762mm (30 Mils) from the chip is recommended. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com |
Price & Availability of HMC449 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |