View ATA6660-TAPY_1181244.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* * * * * * * * * *
Usable for Automotive 12V/24V and Industrial Applications Maximum High-speed Data Transmissions up to 1 MBaud Fully Compatible with ISO 11898 Controlled Slew Rate Standby Mode TXD Input Compatible to 3.3V Short-circuit Protection Overtemperature Protection High Voltage Bus Lines Protection, -40V to +40V High Speed Differential Receiver Stage with a Wide Common Mode Range, -10V to +10V, for High Electromagnetic Immunity (EMI) * Fully Controlled Bus Lines, CANH and CANL to Minimize Electromagnetic Emissions (EME) * High ESD Protection at CANH, CANL HBM 8 kV, MM 300V
High-speed Can Transceiver ATA6660
1. Description
The ATA6660 is a monolithic circuit based on the Atmel's Smart Power BCD60-III technology. It is especially designed for high speed CAN-Controller (CAN-C) differential mode data transmission between CAN-Controllers and the physical differential bus lines. Figure 1-1. Block Diagram
3 VCC
1 TXD
TXD input stage
Overtemperature and Short circuit protection
Driver
7 CANH 8 RS
Constant slope/ standby
4 RXD
Reference Voltage 0.5*VCC
Receiver
6 CANL 5 VREF
2 GND
4582D-BCD-06/06
2. Pin Configuration
Figure 2-1. Pinning SO8
TXD GND VCC RXD 1 2 3 4 8 7 6 5 RS CANH CANL VREF
Table 2-1.
Pin 1 2 3 4 5 6 7 8
Pin Description
Symbol TXD GND VCC RXD VREF CANL CANH RS Function Transmit data input Ground Supply voltage Receive data output Reference voltage output Low level CAN voltage input/output High level CAN voltage input/output Switch standby mode/normal mode
2
ATA6660
4582D-BCD-06/06
ATA6660
3. Functional Description
The ATA6660 is a monolithic circuit based on Atmel's Smart Power BCD60-III technology. It is especially designed for high-speed differential mode data transmission in harsh environments like automotive and industrial applications. Baudrate can be adjusted up to 1 Mbaud. The ATA6660 is fully compatible to the ISO11898, the developed standard for high speed CAN-C (Controller Area Network) communication.
3.1
Voltage Protection and ESD
High voltage protection circuitry on both line pins, CANH (pin 7) and CANL (pin 6), allow bus line voltages in the range of -40V to +40V. ESD protection circuitry on line pins allow HBM = 8 kV, MM = 300V. The implemented high voltage protection on bus line output/input pins (7/6) makes the ATA6660 suitable for 12V automotive applications as well as 24V automotive applications.
3.2
Slope Control
A fixed slope is adjusted to prevent unsymmetrical transients on bus lines causing EMC problems. Controlled bus lines, both CANH and CANL signal, will reduce radio frequency interference to a minimum. In well designed bus configurations the filter design costs can be reduced dramatically.
3.3
Overcurrent Protection
In the case of a line shorts, like CANH to GND, CANL to VCC, integrated short current limitation allows a maximum current of ICANH_SC or ICANL_SC. If junction temperature rises above 165C an internal overtemperature protection circuitry shuts down both output stages, the receiver will stay activated.
3.4
Standby Mode
The ATA6660 can be switched to standby mode by forcing the voltage VRS > 0.87 x VCC. In standby mode the supply current will reduce dramatically, supply current during standby mode is typical 600 A (IVCC_stby). Transmitting data function will not be supported, but the opportunity will remain to receive data. A high-speed comparator is listening for activities on the bus. A dominant bus signal will force the output RXD to a low level in typical tdRXDL = 400 ns. If the RS pin is not connected, causing through a broken connection to the controller, the ATA6660 will switch to standby mode automatically.
3.5
High-speed Receiver
In normal mode a fast receiver circuitry combined with a resistor network is able to detect differential bus line voltages Vrec_th > 0.9V as dominant bit, differential bus line voltages Vrec_th < 0.5V as recessive bit. The wide receiver common mode range, -10V to +10V, combined with a symmetrical differential receiver stage offers high immunity against electromagnetic interference. A typical hysteresis of 70 mV is implemented. Dominant differential bus voltages forces RXD output (pin 4) to low level, recessive differential bus voltages to high level.
3
4582D-BCD-06/06
3.6
TXD Input
The input stage pin 1 (TXD) is compatible for 3.3V output levels from new controller families. Pull-up resistance (25 k) forces the IC to recessive mode, if TXD-Pin is not connected. TXD low signal drives the transmitter into dominant state.
3.7
Transmitter
A integrated complex compensation technique allows stable data transmission up to 1 MBaud. Low level on TXD input forces bus line voltages CANH to 3.5V, CANL to 1.5V with a termination resistor of 60. In the case of a line short circuit, like CANH to GND, CANL to VCC, integrated short current limitation circuitry allows a maximum current of 150 mA. If junction temperature rises above typical 163C an internal overtemperature protection shuts down both output stages, the receive mode will stay activated.
3.8
Split Termination Concept
With a modified bus termination (see Figure 8-3 on page 10) a reduction of emission and a higher immunity of the bus system can be achieved. The one 120 resistor at the bus line end nodes is split into two resistors of equal value, i.e., two resistors of 60. The resistors for the stub nodes is recommended with two resistors of 1.3 k. (for example 8 stub nodes and 2 bus end nodes) Notice: The bus load of all the termination resistors has to stay within the range of 50 to 65. The common mode signal at the centre tap of the termination is connected to ground via a capacitor of e.g., Csplit = 10 nF to 100 nF. A separate ground lead to the ground pin of the module connector is recommended.
4
ATA6660
4582D-BCD-06/06
ATA6660
4. Absolute Maximum Ratings
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Supply voltage DC voltage at pins 1, 4, 5 and 8 DC voltage at pins 6 and 7 Transient voltage at pins 6 and 7 Storage temperature Operating ambient temperature ESD classification ESD classification TStg Tamb All pins Pin 6, 7 versus pin 2 HBM ESD S.5.1 MM JEDEC A115A HBM 1.5 k, 100 pF MM 0, 200 pF Symbol VCC VTXD, VREF, VRS, VRXD VCANH, VCANL 0V < VCC < 5.25V; no time limit Conditions Min. -0.3 -0.3 -40.0 -150 -55 -40 3000 200 8000 300 Max. +6 VCC +0.3 +40.0 +100 +150 +125 Unit V V V V C C V V V V
5. Thermal Resistance
Parameters Thermal resistance from junction to ambient Symbol RthJA Value 160 Unit K/W
6. Truth Table
VCC 4.75V to 5.25V 4.75V to 5.25V 4.75V to 5.25V TXD 0 1 (or floating) X RS < 0.3 x VCC < 0.3 x VCC > 0.87 x VCC CANH 3.5V 0.5 x VCC 0.5 x VCC CANL 1.5V 0.5 x VCC 0.5 x VCC Bus State Dominant Recessive Recessive RXD 0 1 1
7. RS (Pin 8) Functionality
Slope Control Mode Standby Constant slope control Voltage and Current Levels IRS < | 10 A | IRS 500 A
VRS > 0.87 x VCC
VRS < 0.3 x VCC
5
4582D-BCD-06/06
8. Electrical Characteristics
VCC = 4.75V to 5.25V; Tamb = -40C to +125C; RBus = 60; unless otherwise specified. All voltages referenced to ground (pin 2); positive input current. No. 1 1.1 1.2 1.3 2 2.1 2.2 2.3 2.4 3 3.1 3.2 3.3 3.4 4 4.1 4.2 5 5.1 Parameters Supply Current Supply current dominant Supply current recessive VTXD = 0V VRS = 0V VTXD = 5V VRS = 0V 3 3 3 Ivcc_dom Ivcc_rec Ivcc_stby 45 10 600 60 15 980 mA mA A A A A Test Conditions Pin Symbol Min. Typ. Max. Unit Type*
Supply current stand-by VRS = 5V Transmitter Data Input TXD HIGH level input voltage LOW level input voltage VTXD = 5V VRS = 0V VTXD = 0V VRS = 0V
1 1 1 1
VTXDH VTXDL IIH IIL
2 -0.3 -1 -500
VCC + 0.3 +1 0 -50
V V A A
A A A A
HIGH level input current VTXD = VCC LOW level input voltage VTXD = 0V Receiver Data Output RXD High level output voltage Low level output voltage Short current at RXD Short current at RXD IRXD = -100 A IRXD = 1 mA VTXD = 5V VRXD = 0V VTXD = 0V VRXD = 5V VRS = 0V; -50 A < I5 < 50 A VRS = 5 V; -5 A < I5 < 5 A
4 4 4 4
VRXDH VRXDL IRXDs1 IRXDs2
0.8 x VCC 0 -3 2
VCC 0.2 x VCC -1 6
V V mA mA
A A A A
Reference Output Voltage VREF Reference output voltage normal mode Reference output voltage standby mode 5 5 Vref_no Vref_stby 0.45 VCC 0.4 x VCC 0.55 VCC 0.6 VCC V V A A
DC Bus Transmitter CANH; CANL Recessive bus voltage IO(CANH)(reces) IO(CANL)(reces) CANH output voltage dominant CANL output voltage dominant VTXD = VCC; no load -40V < VCANH; VCANL < 40V; 0V < VCC < 5.25V VTXD = 0V VTXD = 0V 6, 7 VCANH; VCANL IO_reces VCANH VCANL 2.0 2.5 3.0 V A
5.2
6, 7
-5
+5
mA
A
5.3 5.4
6, 7 6, 7
2.8 0.5
3.5 1.5
4.5 2.0
V V
A A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
6
ATA6660
4582D-BCD-06/06
ATA6660
8. Electrical Characteristics (Continued)
VCC = 4.75V to 5.25V; Tamb = -40C to +125C; RBus = 60; unless otherwise specified. All voltages referenced to ground (pin 2); positive input current. No. 5.5 5.6 5.7 5.8 6 6.1 Short-circuit CANH current Short-circuit CANL current Differential receiver threshold voltage normal mode Differential receiver threshold voltage stand-by mode Differential input hysteresis CANH and CANL common mode input resistance Differential input resistance Matching between CANH and CANL common mode input resistance CANH, CANL input capacitance Differential input capacitance CANH, CANL input leakage input current Thermal Shut-down Shut-down junction temperature for CANH/CANL Switch on junction temperature for CANH/CANL Temperature hysteresis TJ(SD) 150 163 175 C B VCC = 0V VCANH = 3.5V VCANL = 1.5V Parameters Differential bus output voltage (VCANH - VCANL) Test Conditions VTXD = 0V; RL = 45 to 60; VCC = 4.9V VTXD = VCC; no load VCANH = -10V TXD = 0V VCANL = 18V TXD = 0V Pin 6, 7 6, 7 6, 7 6, 7 Symbol Vdiffdom Vdiffrec ICANH_SC ICANL_SC Min. 1.5 -500 -35 50 Typ. 2 Max. 3.0 +50 -100 150 Unit V mV mA mA Type* A A A A
DC Bus Receiver CANH; CANL -10V < VCANH < +10V -10V < VCANL < +10V VRS = VCC 6, 7 Vrec_th 0.5 0.7 0.9 V A
6.2
6, 7
Vrec_th_stby Vdiff(hys) Ri Rdiff
0.5
0.7
0.9
V
A
6.3
6, 7
70
mV
A
6.4
6, 7
5
15
25
k
A
6.5
6, 7
10
30
100
k
A
6.6
6, 7
Ri_m
-3
+3
%
A
6.7 6.8
6, 7 6, 7
Ci Cdiff ILI(CANH); ILI(CANL)
20 10
pF pF
D D
6.9 7 7.1
6, 7
250
A
A
7.2 7.3
TJ(SD) THys
140
154 10
165
C K
B B
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
7
4582D-BCD-06/06
8. Electrical Characteristics (Continued)
VCC = 4.75V to 5.25V; Tamb = -40C to +125C; RBus = 60; unless otherwise specified. All voltages referenced to ground (pin 2); positive input current. No. 8 8.1 8.2 8.3 8.4 Parameters Delay TXD to bus active Delay TXD to bus inactive Delay TXD to RXD, recessive to dominant Delay TXD to RXD, dominant to recessive Difference between Delay TXD to RXD dominant to Delay recessive Bus dominant to RXD low in stand-by mode Test Conditions Pin Symbol Min. Typ. Max. Unit Type* Timing Characteristics Normal Mode, VRS 0.3 x VCC (see Figure 8-1 on page 9) VRS = 0V VRS = 0V VRS = 0V VRS = 0V tdiff = td_activ(TXD-RXD) - td_inactiv(TXD-RXD) 6, 7 td(TXD-BUS_ON) td(TXD-BUS_OFF) td_activ(TXD-RXD) td_inactiv(TXD-RXD) 120 50 200 180 180 100 420 460 ns ns ns ns A A A A
8.5
tdiff
-280
80
ns
A
9 9.1
Timing Characteristics Stand-by Mode VRS 0.87 x VCC VRS = VCC 4 tdRxDL 300 450 ns A
9.2
Wake up time after stand-by mode (time TXD = 0V delay between stand-by VRS from 0V to VCC to normal mode and to bus dominant) Standby/Normal Mode Selectable via RS (Pin 8) Input voltage for normal VRS = VCC mode Input current for normal VRS = 0V mode Input voltage for stand-by mode
6, 7
Twake_up
2
s
A
10 10.1 10.2 10.3
8 8 8
VRS IRS Vstby -700 0.87 x VCC
0.3 x VCC
V A V
A A A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
8
ATA6660
4582D-BCD-06/06
ATA6660
Figure 8-1. Timing Diagrams
HIGH TXD LOW dominant CANH CANH
CANL dominant CANL dominant (bus activ)
0.9V
Vdiff
0.5V
recessive (bus inactive) HIGH
0.7VCC
RXD
0.3VCC
LOW td (TXD_bus_on) td (TXD_bus_off)
t d_activ(TXD_RXD)
t d_inactiv (TXD_RXD)
9
4582D-BCD-06/06
Figure 8-2.
Test Circuit for Timing Characteristics
TXD GND + 5V VCC RXD
1
8
RS CANH CANL Vref RL=62 CL=100pF
2
7
ATA6660
3 6
4
5
C=47F
C=100nF
C=15pF
Figure 8-3.
Bus Application with Split Termination Concept
CSPLIT =10nF
bus line end node
CAN Controller
TXD GND
RS CANH CANL Vref
RL=60
RL=60
bus line stub node
8
1 2
7
+ 5V
VCC RXD
ATA6660
3 6
C=15pF C=47F C=100nF
4
5
RL=1,3k
RL=1,3k TXD
CAN Controller
RS CANH CANL Vref RL=60 CSPLIT =10nF RL=60
bus line end node
8
1
GND VCC
CSPLIT =10nF
2
7
+ 5V
ATA6660
3 6
RXD
C=47F
C=100nF
C=15pF
4
5
10
ATA6660
4582D-BCD-06/06
ATA6660
9. Ordering Information
Extended Type Number ATA6660-TAPY ATA6660-TAQY Package SO8 SO8 Remarks Taped and reeled, Pb-free Taped and reeled, Pb-free
10. Package Information
Package SO8
Dimensions in mm
5.00 4.85 1.4 0.4 1.27 3.81 8 5 0.25 0.10 0.2 3.8 6.15 5.85 5.2 4.8 3.7
technical drawings according to DIN specifications
1
4
11. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4582D-BCD-06/06 History * Put datasheet in a new template * Pb-free logo on page 1 deleted * Table "Ordering Information" on page 11 changed * * * * Put datasheet in a new template Pb-free logo on page 1 added Heading rows on Table "Absolute Maximum Ratings" on page 5 added Table "Ordering Information" on page 11 changed
4582C-BCD-09/05
11
4582D-BCD-06/06
Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759
Regional Headquarters
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60
Biometrics/Imaging/Hi-Rel MPU/ High-Speed Converters/RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80
Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
(c) 2006 Atmel Corporation. All rights reserved. Atmel (R), logo and combinations thereof, Everywhere You Are(R) and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
4582D-BCD-06/06

▲Up To Search▲

Price & Availability of ATA6660-TAPY

	To Download ATA6660-TAPY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .