View MN101C39C_991696.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MN101C399 , MN101C39C
Type ROM (x 8-bit) x
External memory can be expanded MN101C399 (under planning) 24 K MN101C39C 48 K
RAM (x 8-bit) x
External memory can be expanded
1K
2K
Package (Conventional Package) Minimum Instruction Execution Time
TQFP080-P-1212D *Lead-free (TQFP080-P-1212C) 0.10 s (at 4.5 V to 5.5 V, 20 MHz) 0.25 s (at 2.7 V to 5.5 V, 8 MHz) 125 s (at 2.0 V to 5.5 V, 32 kHz)* * The lower limit for operation guarantee for EPROM built-in type is 2.3 V. * RESET * Watchdog * External 0 * External 1 * External 2 * External 3 * External 4 * Timer 2 * Timer 3 * Timer 4 * Timer 5 * Time base * Serial 0 * Serial 1 * A/D conversion finish Timer counter 2 : 8-bit x 1 (square-wave/8-bit PWM output, event count, synchronous output event) Clock source ********************* 1/1, 1/4 of system clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source **************** coincidence with compare register 2 Timer counter 3 : 8-bit x 1 (square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) Clock source ********************* 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source **************** coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 4 : 16-bit x 1 (square-wave/16-bit PWM output, event count, synchronous output event, input capture) Clock source ********************* 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input Interrupt source **************** coincidence with compare register 4 Time base timer (one-minute count setting, independently operable 8-bit timer counter 5) Clock source ********************* 1/4 of system clock frequency; 1/1, 1/8192 of OSC oscillation clock frequency; 1/1, 1/8192 of XI oscillation clock frequency Interrupt source **************** coincidence with compare register 5; 1/8192 prescaler overflow Watchdog timer Interrupt source **************** 1/65536, 1/262144, 1/1048576 of system clock frequency (ROM option)
Interrupts Timer Counter
Serial Interface
Serial 0 : synchronous type/simple UART (half-duplex) x 1 Clock source ********************* 1/2, 1/4, 1/16 of system clock frequency; 1/2 of timer counter 3 frequency Serial 1 : synchronous type x 1 Clock source ********************* 1/2, 1/8, 1/64 of system clock frequency; 1/2 of timer counter 3 frequency
I/O Pins
I/O Input
49 12
* Common use * Specified pull-up resistor available * Input/output selectable (bit unit) * Specified pull-down resistor partially selectable * Common use * Specified pull-up resistor available * Specified pull-down resistor partially selectable
A/D Inputs LCD Special Ports
10-bit x 8-ch. (with S/H) 28 segments x 4 commons (Static , 1/2, 1/3, or 1/4 duty) Buzzer output, remote control carrier signal output, high-current drive port
1
MAD00015DEM
MN101C399 , MN101C39C
Electrical Characteristics
Supply current
Limit Parameter Symbol IDD1 Operating supply current IDD2 IDD3 Supply current at HALT IDD4 Supply current at STOP IDD5 fx = 32 kHz, VDD = 3 V fx = 32 kHz, VDD = 3 V, Ta = 25C fx = 32 kHz, VDD = 3 V, Ta = -40C to +85C VDD = 5 V, Ta = 25C VDD = 5 V, Ta = -40C to +85C (
P54,SEG26,LED4,A17 P53,SEG27,LED3,A16 P50,LED0,NWE P51,LED1,NRE P52,LED2,NCS
Condition min fosc = 8 MHz, VDD = 5 V typ 8 18 3 max 25 100 8 25 1 20
Unit mA A A A A A
Pin Assignment
P65,SEG20,A5 P64,SEG21,A4 P63,SEG22,A3 P62,SEG23,A2 P61,SEG24,A1 P60,SEG25,A0
) : Conventional Package
P47,KEY7
P46,KEY6
P45,KEY5
P44,KEY4
P43,KEY3
P42,KEY2
P41,KEY1
43
P40,KEY0
42
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
P66,SEG19,A6 P67,SEG18,A7 P70,SEG17,A8 P71,SEG16,A9 P72,SEG15,A10 P73,SEG14,A11 P74,SEG13,A12 P75,SEG12,A13 P76,SEG11,A14 P77,SEG10,A15 P87,SEG9,D7 P86,SEG8,D6 P85,SEG7,D5 P84,SEG6,D4 P83,SEG5,D3 P82,SEG4,D2 P81,SEG3,D1 P80,SEG2,D0 SEG1 SEG0
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9
41
P23,IRQ3
40 39 38 37 36 35 34 33 32
IRQ2,P22 SENS,IRQ1,P21 IRQ0,P20 TM4IO,P14 TM3IO,P13 TM2IO,P12 P11 RMOUT,P10 NRST,P27 NDK,BUZZER,P06 SBT1,P05 SBI1,P04 SBO1,P03 SBT0,P02 RXD, SBI0, P01 TXD, SBO0, P00 VREF+ AN7,PA7 AN6,PA6 AN5,PA5
MN101C399 MN101C39C
31 30 29 28 27 26 25 24 23 22 21
20
COM3
COM2
COM1
COM0
VLC3
VLC2
VLC1
OSC2
OSC1
VSS
XI
VREF-
AN0,PA0
AN1,PA1
AN2,PA2
AN3,PA3
TQFP080-P-1212D *Lead-free (TQFP080-P-1212C)
Support Tool
In-circuit Emulator EPROM Built-in Type
PX-ICE101C / D + PX-PRB101C39-TQFP080-P-1212 Type ROM (x 8-bit) RAM (x 8-bit) Minimum instruction execution time MN101CP39C 48 K 2K 0.10 s (at 4.5 V to 5.5 V, 20 MHz) 0.25 s (at 2.7 V to 5.5 V, 8 MHz) 125 s (at 2.3 V to 5.5 V, 32 kHz)* Package (Conventional Package)
MAD00015DEM
TQFP080-P-1212D *Lead-free (TQFP080-P-1212C)
AN4,PA4
VDD
XO
MMOD
2
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL

▲Up To Search▲

Price & Availability of MN101C39C

	To Download MN101C39C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .