View MFC_748680.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FEATURES
* EMI input filter meets MIL-STD-461C, CE03 * Output filter reduces ripple * -55 to +100C operation * 17 to 40 VDC input, typical * Fully Isolated * 50 V for up to 50 ms transient protection * Inhibit function * Sync function available on select modules * Sense available on select single output modules * Indefinite short circuit protection
w
w
ta a D . w
he S
MULTIPLE OUTPUT (1-8) 28m FILTERED, VIN, co CONFIGURABLE . FACTORY U t4 DC/DC CONVERTERS e
MFC SERIES UP TO 30 WATTS
VDC OUTPUT
Mix or match voltages and power to configure from one to eight outputs.
Size (max):MFCG-H 3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 10.16 mm) MFCA-F 3.005 x 2.260 x 0.400 inches (76.33 x 57.40 x 10.16 mm) Weight: MFCG-H 100 grams maximum MFCA-F 150 grams maximum Screening: Standard or ES
DESCRIPTION
Interpoint's MFC SeriesTM of converters offers one, two, or three individual converters combined with an EMI filter which is designed to meet the requirements of MIL-STD-461C CE03. Many combinations are available with choices from six different output voltages and four different power levels resulting in one package with from one to eight output voltages.
The MFC Series of converters uses Interpoint proprietary modules as building blocks for creating single package optimized solutions with proven reliability and short lead times. All converters have an inhibit function which disables the outputs and places the unit in a low quiescent current mode. Remote sense and margining up are available on the 30 watt single modules. The 15 watt and 30 watt choices have synchronization.
Table 1: Modules - Power and Vout
Power 30 Watt
w
w
w
.D
3.3 5 12 15 18 5 12 15
t a
Vout
S a
Features Inhibit & Sync & Sense/ Trim up Inhibit & Sync Inhibit & Sync
e h
t e
U 4
.c
m o
Power 5 Watt
Vout 5 5.2 12 15 5 12 15 3.3 5 5.2 12 15 5 12 15
Features Inhibit
15 Watt
3.3 5 5.2 12 15 28 5 12 15
1.5 Watt
Inhibit
w
w
w
.D
a
aS t
ee h
4U t
om .c
1
MFC SERIES UP TO 30 WATTS
Configuration Selection Letter1 A B C D E
FILTERED CONFIGURABLE DC/DC CONVERTERS
Table 2: Configurations
Resulting Output Power (W) 30 20 18 11 7 Module Power (Watts) - Number of Modules 30 0 0 0 0 0 15 2 1 1 0 0 5 0 1 0 2 0 1.5 0 0 2 1 4
Case Size: 3.005 x 2.250 x 0.400 inches (76.33 x 57.15 x 10.16 mm
1. Case has eighteen pins which may limit the number of output voltages available. Case Size: 3. 005 x 1.505 x 0.400 inches (76.33 x 38.23 x 10.16 mm) Configuration Selection Letter2 F J G H Resulting Output Power (W) 30 15 6 4 Module Power (Watts) - Number of Modules 30 1 0 0 0 15 0 1 0 0 5 0 0 1 0 1.5 0 0 1 3
2. Case has twelve pins which may limit the number of output voltages available. Selecting a configuration: Begin with the base model letters - MFC. Add a configuration letter from "Table 2: Configurations" that matches the number of outputs and power level you require. Using "Table 1: Modules" from page 1, choose from the available voltages in the power levels determined by the configuration letter. Add the chosen voltages to the model and configuration letters beginning with the highest wattage down to the lowest. As an example: To configure a four output, 20 watt converter, begin with MFCB. Choose the output voltages for the 15 watt and 5 watt modules in Table 2. For this example a 15 watt 5 volt dual output and a 5 watt 15 volt dual output were selected. The resulting configuration is MFCB/05D/15D.
More Examples: MFCA/15D/12D 30 watt total, four outputs: 15 watt dual 15 volt, 15 watt dual 12 volt MFCD/5D/12D/5S 11 watt total, five outputs: 5 watt dual 5 volt, 5 watt dual 12 volt, 1.5 watt single 5 volt MFCG/5D/12D 6 watt total, four outputs: 5 watt dual 5 volt, 1.5 watt dual 12 volt
Note: The specifications on the following pages are for the individual modules. The specifications/performance of the configured converter may vary from the specifications in the "Electrical Characteristics" tables. Please contact the factory for details.
2
FILTERED CONFIGURABLE DC/DC CONVERTERS
Configuration Example: MFCF/05S
MFC SERIES UP TO 30 WATTS
Output Filter +Sense 28 V Input Input Filter L1 0.01 F 4 x 6800 pF / 500 V T1 6 F 6 68 Input Common 2 x 3300 pF / 500 V Inhibit Return Sense Return F 4 x 6800 pF / 500 V 25 Watt Converter 0.15 F 0.03 F Output Common 0.01 F 0.03 F 5 Vout
Inhibit MFCF/05S
Figure 1: MFCF/05S Diagram
Pin 1 2 3 4 5 6 7 8 9 10 11 12
Designation Inhibit Return Inhibit No connection No connection No connection No connection Input Common 28 Vin Sense Return Output Common +5 Vout Positive Sense
Angled corner indicates pin one.
1 2 3 4 5 6
12 11
TOP VIEW MFCF (Pin side, marked side)
10 9 8 7
Note: Pinout will vary depending on the configuration and optons. Figure 2: MFCF/05S Pinout
3
MFC SERIES UP TO 30 WATTS
FILTERED CONFIGURABLE DC/DC CONVERTERS
30 Watt Single Output Modules
SYNC AND INHIBIT
Sync (500 to 675 kHz) * Duty cycle 40% min, 60% max * Logic low 0.8 V max * Logic high 4.5 V min, 5 V max * Referenced to input common * If not used, connect to input common Inhibit TTL Open Collector * Logic low (output disabled) Voltage 0.8 V Inhibit pin current 8.0 mA max * Referenced to input common * Logic high (output enabled) Open collector
ABSOLUTE MAXIMUM RATINGS
Input Voltage * 16 to 40 VDC Output Power * 25 to 30 watts depending on model Lead Soldering Temperature (10 sec per pin) * 300C Storage Temperature Range (Case) * -65C to +135C
TYPICAL CHARACTERISTICS
Output Voltage Temperature Coefficient * 100 ppm/C typical single and dual outputs * 200 ppm/C main, 300 ppm/C aux triple output Input to Output Capacitance * 50 pF typ. (100 pF typ triple outputs) Current Limit * 115% of full load typical Isolation * 100 megohm minimum at 500 V Audio Rejection * 40 dB typ (50 dB typ triple output)l Conversion Frequency * Free run 550 min, 600 typ, 650 max kHz * External sync 500 to 675 kHz Inhibit Pin Voltage (unit enabled) * 9 to 11 V
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range * 16 to 40 VDC continuous * 50 V for 50 msec transient Case Operating Temperature (Tc) * -55C to +100C full power * -55C to +115C absolute Derating Output Power/Current * Linearly from 100% at 100C to 0% at 115C
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
SINGLE OUTPUT MODULES PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT1 OUTPUT POWER1 OUTPUT RIPPLE VOLTAGE LINE REGULATION2 LOAD REGULATION INPUT VOLTAGE1 NO LOAD TO FULL INPUT CURRENT1 CONDITION VIN = 16 to 40 VDC VIN = 16 to 40 VDC 10 kHz - 2 MHz Tc = -55C TO +125C Vin = 16 to 40 VDC Tc = -55C TO +125C NO LOAD TO FULL Tc = -55C TO +125C CONTINUOUS TRANSIENT 50 ms NO LOAD FULL LOAD INHIBITED 10 kHz - 10 MHz Tc = -55C TO +125C SHORT CIRCUIT POWER DISSIPATION RECOVERY1, 4 50% - 100% - 50% TRANSIENT RECOVERY4 16 - 40 - 16 VDC TRANSIENT5 RECOVERY4 DELAY OVERSHOOT FULL LOAD NO LOAD MIN 3.27 0 0 -- -- -- -- -- -- 16 -- -- -- -- -- 74 -- -- -- -- -- -- -- -- -- 3R3S TYP 3.30 -- -- 15 -- 5 -- 2 -- 28 -- 30 0.94 7 25 76 -- 1.4 MAX 3.33 6.06 20 40 50 10 10 10 10 40 50 75 -- 8 50 -- 10 6 MIN 4.95 0 0 -- -- -- -- -- -- 16 -- -- -- -- -- 76 -- -- -- -- -- -- -- -- -- 05S TYP 5.00 -- -- 35 50 10 15 5 15 28 -- 35 1.15 3 20 78 -- 1.4 12S 15S 18S MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS 5.05 11.88 12.00 12.12 14.85 15.00 15.15 17.82 18.00 18.18 VDC 5.0 0 -- 2.5 0 -- 2.0 0 -- 1.67 A 25 50 90 30 50 30 50 40 50 75 -- 8 50 -- 10 5 0 -- -- -- -- -- -- 16 -- -- -- -- -- 80 -- -- -- -- -- -- -- -- -- -- 25 40 10 15 5 15 28 -- 35 1.30 3 20 83 -- 1.4 30 50 90 30 50 30 50 40 50 75 -- 8 50 -- 10 5 0 -- -- -- -- -- -- 16 -- -- -- -- -- 81 -- -- -- -- -- -- -- -- -- -- 25 40 10 15 5 15 28 -- 35 1.25 3 20 84 -- 1.4 30 50 90 30 50 30 50 40 50 75 -- 8 50 -- 10 5 0 -- -- -- -- -- -- 16 -- -- -- -- -- 81 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 28 -- -- 1.33 -- -- -- -- 1.4 -- 60 500 300 -- 0 -- 30 40 90 30 50 30 50 40 50 50 -- 8 50 -- 10 -- 600 -- -- -- 5 -- -- W mV p-p mV mV VDC V mA A mA mA p-p % W ms mV pk s mV pk s ms
INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT3
STEP LOAD RESP.
125 250 -- 200 -- -- 1.4 0 33 300 300 5 50 150
200 300 60 200 200 300 -- 300 1.4 0 50 5 50 250
250 400 60 200 400 500 -- 300 1.4 0 120 5 120 600
350 500 60 200 500 600 -- 300 1.4 0 150 5 150 750
STEP LINE RESP.
START-UP1
mV pk
Notes 1. Tc = -55C to +100C 2. Operation is limited below 16V. 3. Indefinite short circuit protection not guaranteed above 100C case.
4. Recovery time is measured from application of the transient to point at which Vout is within 1% of final value. 5. Transition time 10 s.
4
FILTERED CONFIGURABLE DC/DC CONVERTERS
30 Watt Dual Output Modules
MFC SERIES UP TO 30 WATTS
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
DUAL OUTPUT MODULES PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT1, 2 OUTPUT POWER1, 2 OUTPUT RIPPLE VOLTAGE +/- VOUT LINE REGULATION3 VIN = 16 TO 40 VDC Tc = -55C TO +125C LOAD REGULATION NO LOAD TO FULL Tc = -55C TO +125C CROSS REGULATION EFFECT ON -VOUT INPUT VOLTAGE1 NO LOAD TO FULL INPUT CURRENT SEE NOTE 4 SEE NOTE 5 CONTINUOUS TRANSIENT 50 ms NO LOAD FULL LOAD INHIBITED 10 kHz - 10 MHz POWER DISSIPATION SHORT CIRCUIT1 RECOVERY 50 - 100 - 50% BALANCED TRANSIENT RECOVERY7 16 - 40 - 16 VIN TRANSIENT8 RECOVERY7 DELAY OVERSHOOT FULL LOAD NO LOAD -- -- 0 50 50 250 -- -- 0 120 120 600 -- -- 0 150 150 750 mV pk CONDITIONS +VOUT -VOUT VIN = 16 TO 40 VDC VIN = 16 TO 40 VDC 10 kHz - 2 MHz Tc = -55C TO +125C +VOUT -VOUT +VOUT -VOUT +VOUT -VOUT +VOUT -VOUT MIN 4.95 4.92 0 0 -- -- -- -- -- -- -- -- -- -- -- -- 16 0 -- -- -- -- 76 -- -- -- -- -- -- -- 05D TYP 5.00 5.00 2.5 -- 20 40 10 50 10 50 5 25 5 25 7 4 28 -- 35 1.10 3 15 78 -- 1.4 200 100 200 -- 1.4 MAX 5.05 5.07 4.5 25 50 80 50 100 50 100 30 50 50 100 12 6 40 50 75 -- 8 50 -- 10 5.0 300 200 400 300 5 MIN 11.88 11.82 0 0 -- -- -- -- -- -- -- -- -- -- -- -- 16 0 -- -- -- -- 78 -- -- -- -- -- -- -- 12D TYP 12.00 12.00 1.25 -- 30 40 10 50 10 50 15 30 15 30 4 4 28 -- 50 1.34 3 20 81 -- 1.4 150 100 200 -- 1.4 MAX 12.12 12.18 2.25 30 80 120 30 120 50 150 30 120 50 180 8.3 6 40 50 75 -- 8 50 -- 10 5.0 300 200 400 300 5 MIN 14.85 15D TYP 15.00 MAX 15.15 15.23 1.8 30 80 120 30 150 50 180 30 150 50 180 8 6 40 50 75 -- 8 50 -- 10 5.0 400 200 500 300 5 % VDC V mA A mA mA p-p % W ms mV pk s mV pk s ms mV mV A W mV p-p UNITS VDC
14.77 15.00 0 0 -- -- -- -- -- -- -- -- -- -- -- -- 16 0 -- -- -- -- 80 -- -- -- -- -- -- -- 1.0 -- 25 40 10 50 10 50 15 30 15 30 3 4 28 -- 50 1.29 3 20 83 -- 1.4 200 100 400 -- 1.4
INPUT RIPPLE CURRENT1 EFFICIENCY LOAD FAULT6
STEP LOAD RESPONSE VOUT STEP LINE RESPONSE VOUT START-UP1
Notes 1. Tc = -55C to +100C. 2. Up to 90% of the total output current/power is available from either output providing the positive output is carrying at least 10% of the total output power. 3. Operation is limited below 16 V (see Figure 21). +Pout 20% to 80%; -Pout 80% to 20%
5. Effect on the negative output under the following conditions: +Pout 50%; -Pout 10% to 50% 6. Indefinite short circuit protection not guaranteed above 100C case. 7. Recovery time is measured from application of the transient to point at which Vout is within 1% of final value. 8. Transition time 10 s.
5
MFC SERIES UP TO 30 WATTS
FILTERED CONFIGURABLE DC/DC CONVERTERS
15 Watt Single Output Modules
SYNC AND INHIBIT
Sync In (500 to 600 kHz) * Duty cycle 40% to 60% * Logic low 0.8 V max * Logic high 4.5 V min, 5 V max * Referenced to input common * If not used, connect to input common Inhibit TTL Open Collector * Logic low (output disabled) Logic low voltage 0.8 V Inhibit pin current 4.0 mA max * Referenced to input common * Logic high (output enabled) Open collector or unconnected
ABSOLUTE MAXIMUM RATINGS
Input Voltage * 16 to 40 VDC Power Dissipation (Pd) * 6W Output Power * 12 to 15 watts depending on model Lead Soldering Temperature (10 sec per lead) * 300C Storage Temperature Range (Case) * -65C to +150C
TYPICAL CHARACTERISTICS
Output Voltage Temperature Coefficient * 100 ppm /C typical * 150 ppm/C maximum Input to Output Capacitance * 60 pF typical Undervoltage Lockout * 12 V input typical Current Limit * 115% of full load typical Isolation * 100 megohm minimum at 500 V Audio Rejection * 50 dB typical Conversion Frequency (55C to +100C Tc) * Free run 550 kHz typical 480 kHz min, 620 kHz max Inhibit Pin Voltage (unit enabled) * 8.5 to 12 V
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range * 16 to 40 VDC continuous * 0 V for up to 50 msec transient Case Operating Temperature (Tc) * -55C to +100C full power * -55C to +115C absolute Derating Output Power/Current (Tc) * Linearly from 100% at 100C to 0% at 115C
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
SINGLE OUTPUT MODULES PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE VOLTAGE LINE REGULATION LOAD REGULATION INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT CONDITION VIN = 16 to 40 VDC VIN = 16 to 40 VDC 10 kHz - 2 MHz Tc = -55C to +100C Vin = 16 to 40 VDC NO LOAD TO FULL CONTINUOUS TRANSIENT 50 ms NO LOAD FULL LOAD INHIBITED 10 kHz - 10 MHz Tc = -55C to +100C SHORT CIRCUIT POWER DISSIPATION RECOVERY2 50% - 100% - 50% TRANSIENT RECOVERY2 16 - 40 - 40 VDC TRANSIENT3 RECOVERY2 DELAY OVERSHOOT4 MIN 3.27 0 0 -- -- -- -- 16 -- -- -- -- -- -- 72 -- -- -400 -- -800 -- -- 0 3R3S TYP MAX 3.30 3.33 -- 2.4 -- 30 50 5 20 28 -- 25 -- 5 45 -- 75 5 7.5 150 150 550 0.8 10 200 8 80 120 100 50 40 50 65 397 12 80 120 -- 8 30 500 300 800 1.2 25 300 MIN 4.95 0 0 -- -- -- -- 16 -- -- -- -- -- -- 75 -- -- -400 -- -800 -- 0 0 05S TYP MAX 5.00 5.05 -- 2.4 -- 30 60 5 20 28 -- 25 560 5 35 -- 77 3.5 7.5 150 150 550 0.8 10 100 12 80 100 50 50 40 50 40 624 12 80 100 -- 6 30 400 300 800 1.2 25 600 MIN 5.16 0 0 -- -- -- -- 16 -- -- -- -- -- -- 75 -- -- -400 -- -800 -- 0 0 5R2S TYP MAX 5.20 5.24 -- 2.4 -- 30 60 5 20 28 -- 25 560 5 35 -- 77 .35 7.5 150 150 550 0.8 10 100 12.48 50 100 35 35 40 50 42 605 12 100 120 -- 6 30 400 300 800 1.2 18 300 UNITS VDC A W mV p-p mV mV VDC V mA
INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT1
mA pp % W ms mV pk s mV pk ms ms mV pk
STEP LOAD RESP.
STEP LINE RESP.
START-UP
Notes 1. Indefinite short circuit protection not guaranteed above 100C (case) 2. Recovery time is measured from application of the transient to point at which Vout is within regulation.
3. Input step transition time >10s. 4. Input step transition time <100s.
6
FILTERED CONFIGURABLE DC/DC CONVERTERS
15 Watt Single Output Modules
MFC SERIES UP TO 30 WATTS
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
SINGLE OUTPUT MODULES PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE VOLTAGE LINE REGULATION LOAD REGULATION INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT CONDITION VIN = 16 to 40 VDC VIN = 16 to 40 VDC 10 kHz - 2 MHz Tc = -55C to +100C Vin = 16 to 40 VDC NO LOAD TO FULL CONTINUOUS TRANSIENT 50 ms NO LOAD FULL LOAD INHIBITED 10 kHz - 10 MHz Tc = -55C to +100C SHORT CIRCUIT POWER DISSIPATION RECOVERY2 50% - 100% - 50% TRANSIENT RECOVERY2 16 - 40 - 40 VDC TRANSIENT3 RECOVERY2 DELAY OVERSHOOT4 12S MIN TYP MAX 11.88 12.00 12.12 0 -- 1.25 0 -- -- -- -- 16 -- -- -- -- -- -- 78 -- -- -500 -- -800 -- 0 0 -- 30 50 5 20 28 -- 25 680 5 35 -- 79 3.5 7.5 150 150 550 0.8 10 15 80 120 50 50 40 50 50 752 12 80 120 -- 6 30 500 300 800 1.2 25 15S MIN TYP MAX 14.85 15.00 15.15 0 -- 1.00 0 -- -- -- -- 16 -- -- -- -- -- -- 78 -- -- -600 -- -800 -- 0 0 -- 30 50 5 20 28 -- 25 670 5 35 -- 80 3.5 7.5 200 150 550 0.8 10 15 80 120 50 50 40 50 62 752 12 80 120 -- 6 30 600 300 800 1.2 25 28S MIN TYP MAX 27.72 28.00 28.28 0 -- 0.54 0 -- -- -- -- 16 -- -- -- -- -- -- 82 -- -- -800 -- -- 60 100 50 50 28 -- 25 640 5 35 -- 84 3.5 7.5 600 200 15 120 180 150 150 40 50 60 760 12 80 120 -- 6 30 800 400 UNITS VDC A W mV p-p mV mV VDC V mA
INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT1
mA pp % W ms mV pk s mV pk ms ms mV pk
STEP LOAD RESP.
STEP LINE RESP.
-1200 1100 1200 -- 0.8 1.2 0 0 10 200 25 280
START-UP
200 1200
200 1500
Notes 1. Indefinite short circuit protection not guaranteed above 100C (case) 2. Recovery time is measured from application of the transient to point at which Vout is within regulation.
3. Input step transition time >10s. 4. Input step transition time <100s.
7
MFC SERIES UP TO 30 WATTS
FILTERED CONFIGURABLE DC/DC CONVERTERS
15 Watt Dual Output Modules
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, free run, unless otherwise specified.
DUAL OUTPUT MODULES PARAMETER OUTPUT VOLTAGE CONDITIONS +VOUT -VOUT OUTPUT CURRENT1 OUTPUT POWER1 OUTPUT RIPPLE VOLTAGE VOUT LINE REGULATION Vin = 16 to 40 VDC LOAD REGULATION VIN = 16 to 40 VDC VIN = 16 to 40 VDC 10 kHz - 2 MHz Tc = -55C to +100C BALANCED +VOUT LOAD -VOUT -VOUT BALANCED +VOUT LOAD CROSS REGULATION2 INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT MIN 4.95 4.92 -- -- -- -- -- -- -- -- -- 16 -- -- -- -- -- -- 77 -- -- -600 -600 -- -800 -- -- 0 05D TYP 5.00 5.00 1.2 -- 30 60 5 -- 20 -- 6 28 -- 20 540 6 20 40 79 3 7.5 200 150 150 600 0.8 12 100 MAX 5.05 5.08 1.92 12 80 120 50 80 50 100 7.5 40 50 40 600 12 50 80 -- 6 30 600 600 500 800 1.2 20 250 MIN 11.88 11.82 -- -- -- -- -- -- -- -- -- 16 -- -- -- -- -- -- 76 -- -- -600 -600 -- -750 -- -- 0 12D TYP 12.00 12.00 0.625 -- 30 60 5 -- 20 -- 3 28 -- 25 645 5 35 50 83 3 7.5 300 100 200 550 0.8 12 200 MAX 12.12 1218 1.125 15 80 120 50 100 50 100 6 40 50 50 754 12 60 100 -- 6 50 600 500 400 750 1.2 25 750 MIN 14.85 14.78 -- -- -- -- -- -- -- -- -- 16 -- -- -- -- -- -- 76 -- -- -600 -600 -- -750 -- -- 0 15D TYP 15.00 15.00 0.500 -- 30 50 5 -- 20 -- 3 28 -- 25 638 5 35 50 84 3 7.5 300 100 200 550 0.8 12 200 MAX 15.15 15.23 0.900 15 80 120 50 100 50 100 6 40 50 50 754 12 60 100 -- 6 50 600 600 500 750 1.2 25 750 s mV pk ms ms mV pk % VDC V mA mV A W mV p-p mV UNITS VDC
NEGATIVE VOUT CONTINUOUS TRANSIENT 50 msec NO LOAD FULL LOAD INHIBITED 10 kHz - 10 MHz Tc = -55C to +100C SHORT CIRCUIT3 POWER DISSIPATION RECOVERY4 50% - 100% - 50% +VOUT TRANSIENT -VOUT RECOVERY4 16 - 40 - 40 VDC TRANSIENT6 RECOVERY4 DELAY OVERSHOOT7
INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT
mA p-p % W ms
STEP LOAD RESP.5
mV pk
STEP LINE RESP. VOUT START-UP
Notes 1. Up to 13.5 watts, 90% (9.6W, 80% for 2805D) of the total output power is available from either output providing the opposite output is simultaneously carrying 10% (20% for 2805D) of the total output power. Each output must carry a minimum of 10% (20% for 2805D) of the total output power in order to maintain regulation on the negative outputs. 2. Effect on -Vout for the following conditions: +Po = 50% to 10% and -Po = 50% +Po = 50% and -Po = 50% to 10%
3. Indefinite short circuit protection not guaranteed above 100C (case) 4. Recovery time is measured from application of the transient to point at which Vout is within regulation. 5. Response of either output with the opposite output held at half of the total output power. 6. Input step transition time >10s. 7. Input step transition time <100s.
8
FILTERED CONFIGURABLE DC/DC CONVERTERS
5 Watt Single Output Modules
ABSOLUTE MAXIMUM RATINGS
Input Voltage * 16 to 40 V Output Power * 5 watts Lead Soldering Temperature (10 sec per lead) * 300C Storage Temperature Range (Case) * -65C to +135C
MFC SERIES UP TO 30 WATTS
INHIBIT
Inhibit TTL Open Collector * Logic low (output disabled) Logic low voltage 0.8 V Inhibit pin current 4 mA max * Referenced to input common * Logic high (output enabled) Open collector
TYPICAL CHARACTERISTICS
Output Voltage Temperature Coefficient * 100 ppm/C typical Input to Output Capacitance * 50 pF typical Isolation * 100 megohm minimum at 500 V Audio Rejection * 50 dB typical Conversion Frequency * 550 kHz typical (400 kHz 60 V model) 450 kHz min, 600 kHz max 350 kHz min, 450 kHz max 60 V model Inhibit Pin Voltage (unit enabled) * 9 to 11 V
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range * 16 to 40 VDC continuous * 50 V for up to 50 msec transient Case Operating Temperature (Tc) * -55C to +100C full power * -55C to +115C absolute Derating Output Power/Current (Tc) * Linearly from 100% at 100C to 0% at 115C
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
SINGLE OUTPUT MODULES PARAMETER CONDITIONS OUTPUT VOLTAGE Tc = -55C TO +100C OUTPUT CURRENT Tc = -55C TO +100C VIN = 16 TO 40 VDC OUTPUT POWER OUTPUT RIPPLE VOLTAGE LINE REGULATION LOAD REGULATION INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT Tc = -55C TO +100C INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT2, 3 SHORT CIRCUIT STEP LOAD RESPONSE3, 4 STEP LINE RESPONSE3, 4 VIN = 16 TO 40 VDC Tc = -55C TO +100C 10 kHz - 2 MHz VIN = 16 TO 40 VDC Tc = -55C TO +100C NO LOAD TO FULL Tc = -55C TO +100C Tc = -55C TO +100C CONTINUOUS TRANSIENT 50 ms NO LOAD FULL LOAD INHIBITED 10 kHz - 10 MHz Tc = -55C TO +100C POWER DISSIPATION RECOVERY 50% - 100% - 50% TRANSIENT RECOVERY TRANSIENT 16 TO 40 VIN 40 TO 16 VIN RECOVERY 16 TO 40 VIN 40 TO 16 VIN START-UP DELAY OVERSHOOT -- -- -- -- 100 200 10 0 250 500 25 50 -- -- -- -- 100 200 10 0 250 500 25 50 -- -- -- -- 250 250 3 0 625 625 10 120 -- -- -- -- 250 250 3 0 625 625 10 150 s ms mV pk -- -- -- -- 16 0 -- -- -- -- -- 66 -- -- -- -- -- -- -- 125 10 10 28 -- 27 250 3 25 30 71 1.5 12.5 100 100 50 50 5 350 501 50 40 50 40 -- 4 100 150 -- 2.0 25 250 250 150 150 -- -- -- -- 16 0 -- -- -- -- -- 66 -- -- -- -- -- -- -- 110 10 10 28 -- 28 250 3 25 30 71 1.5 1.5 100 100 50 50 5 335 50 50 40 50 40 -- 4 100 150 -- 2.0 25 250 250 150 150 -- -- -- -- 16 0 -- -- -- -- -- 70 -- -- -- -- -- -- -- 50 10 10 28 -- 29 235 3 25 30 76 1.2 1 150 200 80 100 5 200 50 50 40 50 42 -- 4 100 150 -- 1.9 10 375 500 200 250 -- -- -- -- 16 0 -- -- -- -- -- 71 -- -- -- -- -- -- -- 50 10 10 28 -- 31 235 3 25 30 76 1.2 1 200 200 50 50 5 170 50 50 40 50 44 -- 4 100 150 -- 1.8 10 500 500 125 125 W mV p-p mV mV VDC V 5S MIN TYP 4.95 5.00 0 -- MAX MIN 5.05 5.15 1000 0 5R2S 12S 15S TYP MAX MIN TYP MAX MIN TYP MAX 5.20 5.25 11.88 12.00 12.12 14.85 15.00 15.15 -- 962 0 -- 417 0 -- 333 UNITS VDC mA
mA mA p-p % W ms mV pk s
mV pk
Notes 1. Line regulation for /ES and non /ES 2805S models at 16 to 17 VIN and 85C to 100C (case) is 5% (max). 2. Indefinite short circuit protection not guaranteed above 100C (case).
3. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value. 4. Transition time >10s.
9
MFC SERIES UP TO 30 WATTS
DUAL OUTPUT MODULES PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT1 OUTPUT POWER1 OUTPUT RIPPLE VOLT. LINE REGULATION Vin = 16 to 40 VDC
FILTERED CONFIGURABLE DC/DC CONVERTERS
5 Watt Dual Output Modules
05D CONDITIONS +VOUT -VOUT VIN = 16 to 40 VDC Tc = -55C to +125C VIN = 16 to 40 VDC Tc = -55C to +125C 10 kHz - 2 MHz Tc = -55C to +125C +VOUT -VOUT Tc = -55C to +125C +VOUT -VOUT MIN 4.95 4.9 -- -- -- -- -- -- -- -- TYP 5.00 5.0 500 -- -- 10 40 10 50 10 MAX 5.05 5.1 800 5 150 25 75 50 200 20 MIN 11.88 11.76 -- -- -- -- -- -- -- -- 12D TYP 12.00 12.00 208 -- 40 10 40 10 50 8 MAX 12.12 12.24 333 5 140 50 180 50 200 15 MIN 14.85 14.70 -- -- -- -- -- -- -- -- 15D TYP 15.00 15.00 167 -- 60 10 40 10 50 7 MAX 15.15 15.30 267 5 150 50 180 50 200 15 % -- 5 8 -- 3.7 6 -- 3 6 mA W mV p-p UNITS VDC
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
mV
LOAD REGULATION NO LOAD TO FULL
mV
CROSS REGULATION2
+PO = 20 - 80 %, -PO = 80 - 20% -PO = 20 - 80 %, +PO = 80 - 20% +PO = 50 - 10 %, -PO = 50% -PO = 50 - 10 %, +PO = 50%
INPUT VOLTAGE Tc = -55C to +125 INPUT CURRENT Tc = -55C to +125C INPUT RIPPLE CURRENT EFFICIENCY LOAD FAULT3, 4
NO LOAD TO FULL CONTINUOUS TRANSIENT 50 msec NO LOAD FULL LOAD INHIBITED 10 kHz TO 10 MHz Tc = -55C to +125C POWER DISSIPATION SHORT CIRCUIT RECOVERY 50% - 100% - 50% BALANCED TRANSIENT RECOVERY
16 -- -- -- -- -- -- 68 -- -- -- --
28 -- 30 248 3 25 30 72 1.3 -- -- -- -- -- -- -- -- --
40 50 35 -- 5 80 160 -- 1.8 50 150 100 750 500 1200 1200 25 500
16 -- -- -- -- -- -- 69 -- -- -- -- -- -- -- -- -- --
28 -- 33 235 3 25 30 75 1.3 1 300 200 50 50 150 400 3 0
40 50 58 -- 4 100 150 -- 1.7 10 750 500 125 125 375 1000 10 120
16 -- -- -- -- -- -- 70 -- -- -- -- -- -- -- -- -- --
28 -- 38 235 3 25 30 75 1.3 1 300 500 150 100 250 800 3 0
40 50 60 -- 4 100 150 -- 1.6 10 750 1250 375 250 625 2000 10 150
VDC V mA
mA p-p % W ms mV s mV pk s ms mV pk
STEP LOAD RESPONSE4, 5
STEP LINE RESP.4, 5
16 TO TRANSIENT 40 TO 16 TO RECOVERY 40 TO
40 16 40 16
VDC VDC VDC VDC
-- -- -- -- -- --
START-UP
DELAY OVERSHOOT
Notes 1. Up to 4 watts (80% full power) is available from either output providing the opposite output is carrying 20% of total power. 2. Shows regulation effect on the minus output during the defined cross loading conditions. See Figures 15 and 16.
3. Indefinite short circuit protection not guaranteed above 100C (case). 4. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value. 5. Transition time >10s.
10
FILTERED CONFIGURABLE DC/DC CONVERTERS
1.5 Watt Single Output Modules
ABSOLUTE MAXIMUM RATINGS
Input Voltage * 12 to 50 VDC Output Power * 1.5 W Capacitive Load * Single output models 200 F * Dual output models 100 F Lead Soldering Temperature (10 sec per lead) * 300C Storage Temperature Range (Case) * -65C to +150C
MFC SERIES UP TO 30 WATTS
INHIBIT
Inhibit - TTL Open Collector * Logic low (output disabled) 0.8 V max Inhibit pin current 1 mA max * Referenced to input common * Logic high (output enabled) open collector
TYPICAL CHARACTERISTICS
Output Voltage Temperature Coefficient * 100 ppm/C typical Input to Output Capacitance * 100 to 170 pF typical Undervoltage Lockout * 8 V input typical Current Limit * 125% of full load typical Isolation * 100 megohm minimum at 500 V Audio Rejection 40 dB, typical Conversion Frequency (kHz) * 25C, 300 min, 370 typ, 450 max * -55C to +100C 270 min, 370 typ, 470 max Inhibit Pin Voltage (unit enabled) * 7 to 12 V
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range * 12 to 50 VDC continuous * 80 V for 120 msec transient (70 V for 15 V single and dual models) Case Operating Temperature (Tc) * -55C to +100C full power * -55C to +115C absolute Derating Output Power/Current (Tc) * Linearly from 100% at 100C to 0% at 115C
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
SINGLE OUTPUT MODULES PARAMETER CONDITIONS OUTPUT VOLTAGE1 Tc = 25C Tc = -55C TO +100C OUTPUT CURRENT VIN = 12 to 50 VDC OUTPUT POWER OUTPUT RIPPLE VOLTAGE LINE REGULATION LOAD REGULATION VIN = 12 TO 50 VDC 10 kHz - 2 MHz Tc = -55C TO +100C VIN = 12 TO 50 VDC Tc = -55C TO +100C 10% TO FULL LOAD Tc = -55C TO +100C 50% TO FULL Tc = -55C TO +100C CONTINUOUS TRANSIENT 120 ms NO LOAD Tc = -55C TO +100C FULL LOAD Tc = -55C TO +100C INHIBITED Tc = -55C TO +100C 10k Hz - 10 MHz Tc = -55C TO +100C Tc = 25C Tc = -55C TO +100C POWER DISSIPATION Tc = -55C TO +100C RECOVERY Tc = --55C TO +100C 50 %-100%- 50% LOAD TRANSIENT Tc = -55C TO +100C RECOVERY Tc = -55C TO +100C 12 TO 50 TO 12 VIN TRANSIENT Tc = -55C TO +100C RECOVERY Tc = -55C TO +100C DELAY Tc = -55C TO +100C OVERSHOOT Tc = -55C TO +100C 3R3S MIN TYP MAX MIN 4.95 4.80 0 -- 0 0 -- 0 -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 72 69 -- -- -- -- -400 -500 -- -- 05S 5R2S 12S 15S TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX 5 5.05 5.15 5.2 5.25 11.88 12 12.12 14.85 15 15.15 5 5.20 5.00 5.2 5.40 11.52 12 12.48 14.40 15 15.60 -- 300 0 -- 288 0 -- 125 0 -- 100 -- 45 65 35 40 350 380 100 115 28 -- 5.5 6.0 70 73 2.3 2.4 100 130 77 75 1.3 1.4 3.0 3.5 185 185 125 125 1.5 150 300 100 120 700 800 200 300 50 80 10 11 74 78 3.2 3.5 200 250 -- -- 2.0 2.3 12 15 400 500 500 600 400 500 3.0 4.0 20 40 100 150 0 -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 75 69 -- -- -- -- -400 500 -- -- -400 -500 -- -- -- -- -- -- -- 45 65 35 40 350 380 100 115 28 -- 5.5 6.0 70 73 2.3 2.4 100 130 77 75 1.3 1.4 3.0 3.5 185 185 125 125 170 180 0.75 0.75 7 10 0 0 1.5 150 300 100 120 700 800 200 300 50 80 10 11 74 78 3.2 3.5 200 250 -- -- 2.0 2.3 12 15 400 500 500 600 0 -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 74 72 -- -- -- -- -700 -800 -- -- -- 1.5 0 -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 74 72 -- -- -- -- -700 -800 -- -- -- 1.5 UNITS VDC mA W mV p-p mV
INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT
INPUT RIPPLE CURRENT2 EFFICIENCY LOAD FAULT3, 4
-- -- -- -- -- -- -- -- 12 28 50 0 -- 80 -- -- -- AVAILABLE -- -- SOON, ASK -- YOUR -- INTERPOINT -- REP FOR -- -- INFORMATION -- -- -- --
50 200 70 300 60 200 70 250 600 1300 640 1400 145 300 160 400 28 50 -- 80 6 10 6.5 12 68 72 70 74 2.3 3.2 2.4 3.5 100 200 150 250 79 -- 77 -- 2.0 3.2 2.2 3.5 3.5 15 3.5 20 350 380 130 130 700 800 500 600
35 150 50 250 70 300 80 350 700 1500 760 1600 165 350 185 450 28 50 -- 70 6.0 11 6.5 12 68 72 70 74 2.3 3.2 2.4 3.5 100 200 150 250 79 -- 77 -- 2.3 3.7 2.5 4.0 4.0 18 4.0 20 350 380 140 180 700 800 600 750 750 850 2.0 2.5 20 40 300 450
mV
VDC V
mA
mA p-p % W ms
STEP LOAD RESPONSE5
mV pk s
-- --
STEP LINE RESPONSE5
START-UP 0 TO 28 VDC
-- -- -- -- -- --
0 0
-400 170 -500 180 -- 0.75 -- 0.75 -- 7 -- 10 -- 0 -- 0
400 -900 400 900 500 -1000 400 1000 3.0 -- 0.6 2.5 4.0 -- 0.6 3.0 20 -- 7 20 40 -- 10 40 100 -- 0 250 150 -- 0 350
-750 400 -850 450 -- 0.47 -- 0.5 -- 7 -- 10 -- 0 -- 0
mV pk ms ms mV pk
See notes 1, 2, 3, 4, 5, and 6 on the following page.
11
MFC SERIES UP TO 30 WATTS
FILTERED CONFIGURABLE DC/DC CONVERTERS
1.5 Watt Dual Output Modules
Electrical Characteristics: 25C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
DUAL OUTPUT MODULES PARAMETER CONDITIONS Tc = 25C OUTPUT VOLTAGE1 Tc = -55C TO +100C OUTPUT CURRENT6 VIN = 12 TO 50 VDC OUTPUT POWER OUTPUT RIPPLE VOLTAGE +VOUT -VOUT LINE REGULATION7 LOAD REGULATION8 VOUT VIN = 12 TO 50 VDC 10 kHz - 2 MHz Tc = -55C TO +100C 10 kHz - 2 MHz Tc = -55C TO +100C VIN = 12 TO 50 VDC Tc = -55C TO +100C 10% TO FULL -55C TO +100C 50% TO FULL -55C TO +100C CONTINUOUS TRANSIENT 120 ms NO LOAD Tc = -55C TO +100C FULL LOAD Tc = -55C TO +100C INHIBITED Tc = -55C TO +100C 10 kHz - 10 MHz Tc = -55C TO +100C Tc = 25C Tc = -55C TO +100C 5D MIN TYP 4.95 5 4.80 5 0 150 0 -- -- -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 73 70 -- -- -- -- -300 -400 -- -- -250 -300 -- -- -- -- -- -- -- 35 50 35 50 10 20 300 350 80 100 28 -- 5.0 6.0 69 72 2.3 2.4 100 130 77 75 1.4 1.6 3.7 3.8 130 140 100 100 125 130 0.6 0.6 8 10 0 0 MAX 5.05 5.20 240 1.5 150 250 150 250 50 100 600 700 200 300 50 80 10 12 73 77 3.2 3.5 200 250 -- -- 2.2 2.5 15 20 300 400 400 500 250 300 2.5 3.0 25 45 100 150 12D MIN TYP MAX MIN 11.88 12 12.12 14.85 11.52 12 12.48 14.40 0 62.5 100 0 0 -- -- -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 73 70 -- -- -- -- -600 -700 -- -- -500 -600 -- -- -- -- -- -- -- 35 40 35 40 100 110 550 570 115 130 28 -- 7.5 8.0 70 71 2.3 2.4 115 150 77 75 2.5 2.7 3.2 3.2 250 260 165 165 240 250 0.9 0.9 8 10 0 0 1.5 150 250 150 250 300 400 1100 1200 250 350 50 80 13 14 73 77 3.2 3.5 200 250 -- -- 3.8 4.2 15 20 600 700 700 800 500 600 3.0 4.0 25 45 250 350 0 -- -- -- -- -- -- -- -- -- -- 12 0 -- -- -- -- -- -- -- -- 72 69 -- -- -- -- -600 -700 -- -- -500 -600 -- -- -- -- -- -- 15D TYP MAX 15 15.15 15 15.60 50 80 -- 30 35 30 35 165 180 600 630 125 135 28 -- 7.5 8.0 71 72 2.3 2.4 90 120 76 74 2.7 3.0 4.0 4.0 250 270 50 50 220 230 0.6 0.7 8 10 0 0 1.5 150 250 150 250 500 650 1300 1400 300 400 50 70 13 14 74 78 3.2 3.5 200 250 -- -- 4.1 4.5 15 20 600 700 200 300 500 600 3.0 4.0 25 45 750 900 UNITS VDC mA W
mV p-p
mV
mV
INPUT VOLTAGE NO LOAD TO FULL INPUT CURRENT
VDC V
mA
INPUT RIPPLE2 CURRENT EFFICIENCY LOAD FAULT3,4
mA p-p % W ms
POWER DISSIPATION Tc = -55C TO +100C RECOVERY Tc = -55C TO +100C STEP LOAD 50 %-100%- 50% LOAD TRANSIENT RESPONSE5 VOUT Tc = -55C TO +100C RECOVERY -55C TO +100C STEP LINE 12 TO 50 TO 12 VIN RESPONSE5 VOUT TRANSIENT Tc = -55C TO +100C RECOVERY Tc = -55C TO +100C START-UP DELAY 0 TO 28 VDC, VOUT Tc = -55C TO +100C OVERSHOOT Tc = -55C TO +100C
mV pk s
mV pk ms ms mV pk
Notes: 1. Specified at 50% load. 2. Lin = 2 H. 3. Maximum duration of short circuit:: 25C-- 90 seconds, 100C - 30 seconds. 4. Load fault is a short circuit (<50 mohms). Recovery is into resistive full load. 5. Transition 10 s. Recovery = time to settle to within 1% of Vout final value.
6. Max. spec indicates 80% of the converter's total power, available from either output. 7. Specification applies to both + and - Vout. 8. Although no minimum load is required, at no load the output voltage may increase up to 15%.
12
FILTERED CONFIGURABLE DC/DC CONVERTERS
Case Outline Drawings Pinouts will vary depending on customer choices.
MFC SERIES UP TO 30 WATTS
0.23 (5.8) Lead Length
2.250 2.130 1.925 1.725 0.525 1.325 1.125 0.925 0.725 0.525 0.325 0.120 0.000 1 2 3 4 5 6 7 8 9 Top View 18 17 16 15 14 13 12 11 10
18x 0.040 0.002 PIN
0.000 0.120 0.250+/- 0.010
2.750 +/- 0.010 2.880
4x 0.128 + 0.002/ -0.001 Thru
Figure 3: Case for A through E Options Case size 3.005 x 2.260 x 0.400 inches , 76.33 x 57.40 x 10.16 mm
3.000 +0.005/-0.010
0.400 (10.16) max.
0.220 (5.59 0.050 (1.27) 0.000
13
MFC SERIES UP TO 30 WATTS
FILTERED CONFIGURABLE DC/DC CONVERTERS
Case Outline Drawings Pinouts will vary depending on customer choices.
Angled corner indicates pin one. 1.505 (38.23) max. 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 0.000
Seam Seal
0.23 (5.8) Lead Length 0.128 dia (3.25). 0.040 dia (1.02) 1 2 3 4 5 6 12 11 10
TOP VIEW (Pin side, marked side)
9 8 7
2.750 (69.85)
2.880 (73.15) 3.005 (76.33) max.
Figure 4: Case for F through H Options
Case size 3.005 x 1.500 x 0.400 inches, 76.33 x 38.23 x 10.16 mm
14
0.400 (10.16) max.
0.050 (1.27) 0.000
0.120 (3.05) 0.250 (6.35)
0.220 (5.59
FILTERED CONFIGURABLE DC/DC CONVERTERS
Table 4: ENVIRONMENTAL SCREENING
TEST PRE-CAP INSPECTION Method 2017, 2032 TEMPERATURE CYCLE (10 times) Method 1010, Cond. B, -55C to 125C CONSTANT ACCELERATION Method 2001, 500 g BURN-IN Method 1015, 96 hours at 100C case FINAL ELECTRICAL TEST MIL-PRF-38534, Group A Subgroups 1 and 4: +25C case HERMETICITY TESTING Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Gross Leak, Dip (1 x 10-3) FINAL VISUAL INSPECTION Method 2009 STANDARD
MFC SERIES UP TO 30 WATTS
/ES
no
yes
no
yes
no
yes
no
yes
yes
yes
no no yes
yes yes no
yes
yes
Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534.
Contact Information: Interpoint Headquarters USA Phone: 1-800-822-8782 +425-882-3100 Email: power@intp.com
www.interpoint.com Interpoint UK Phone: +44-1252-815511 Email: poweruk@intp.com Interpoint France Phone: +33-134285455 Email: powerfr@intp.com
MFC-DTS Rev D. This revision supercedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. MFC Series is a trademark of Interpoint. Copyright (c) 2000-2001 Interpoint. All rights reserved.
15

▲Up To Search▲

Price & Availability of MFC

	To Download MFC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .