View FAN533105_741757.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
August 2005
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Features
1.6MHz Switching Frequency Low Noise Low RDS(ON): 0.5 Adjustable Output Voltage 1A Peak Switch Current 1W Output Power Capability Low Shutdown Current: <1A Cycle-by-Cycle Current Limit Over-Voltage Protection Fixed-Frequency PWM Operation Internal Compensation 5-lead SOT-23 Package
Description
The FAN5331 is a general purpose, fixed-frequency boost converter designed to operate at high switching frequencies in order to minimize switching noise measured at the battery terminal of hand-held communications equipment. Quiescent current in normal mode of operation as well as in shutdown mode is designed to be minimal in order to extend battery life. Normal mode of operation or shutdown mode can be selected by a logic level shutdown circuitry. The low ON-resistance of the internal N-channel switch ensures high efficiency and low power dissipation. A cycle-by-cycle current limit circuit keeps the peak current of the switch below a typical value of 1A. The FAN5331 is available in a 5-lead SOT23 package.
Applications
Cell Phones PDAs Handheld Equipment Display Bias LED Bias
Typical Application
VIN CIN 4.7F 5 VIN 1 R1 CF 120pF 2.7V to 5.5V L 10H BAT54 COUT 4.7F VOUT
SW
FAN5331
FB
3
R2 ON OFF 4 SHDN GND 2
Figure 1. Typical Application Diagram
(c)2004 Fairchild Semiconductor Corporation
1
www.fairchildsemi.com
FAN5331 Rev. 1.0.1
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Pin Assignment
Top View SW GND FB VIN SHDN
5-Lead SOT-23
Figure 2. Pin Assignment
Pin Description
Pin No.
1 2 3 4 5
Pin Name
SW GND FB SHDN VIN Switching node. Analog and power ground.
Pin Description
Feedback node that connects to an external voltage divider. Shutdown control pin. Logic HIGH enables, logic LOW disables the device. Input voltage.
Absolute Maximum Ratings (Note1)
Parameter
VIN to GND FB, SHDN to GND SW to GND Lead Soldering Temperature (10 seconds) Junction Temperature Storage Temperature Thermal Resistance (JA) Electrostatic Discharge Protection (ESD) Level (Note 2) HBM CDM 2.5 1 -55 -0.3 -0.3
Min
Max
6.0 VIN + 0.3 23 300 150 150 265
Unit
V V V C C C C/W kV
Recommended Operating Conditions
Parameter
Input Voltage Output Voltage Operating Ambient Temperature Output Capacitance (Note 3)
Min
2.7 VIN -40 1.6
Typ
Max
5.5 20
Unit
V V C F
25
85
Notes: 1. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Absolute maximum ratings apply individually only, not in combination. 2. Using EIA/JESD22A114B (Human Body Model) and EIA/JESD22C101-A (Charge Device Model). 3. This load capacitance value is required for the loop stability. Tolerance, temperature variation, and voltage dependency of the capacitance must be considered. Typically a 4.7F ceramic capacitor is required to achieve specified value at VOUT = 15V.
2 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Electrical Characteristics
Unless otherwise noted, VIN = 3.6V, TA = -40C to +85C, Typical values are at TA = 25C, Test Circuit, Figure 3. Parameter
Switch Current Limit Load Current Capability Switch On-resistance Quiescent Current OFF Mode Current Shutdown Threshold Shutdown Pin Bias Current Feedback Voltage Feedback Pin Bias Current Feedback Voltage Line Regulation Switching Frequency Maximum Duty Cycle Enable Delay Power on Delay Switch Leakage Current VIN = 2.7V, IOUT = 35mA, VOUT = 15V VIN = 2.7V, IOUT = 35mA, VOUT = 15V No Switching, VIN = 5.5V 2.7V < VIN < 5.5V, ILOAD = 0mA 1.15 87 VIN = 3.2V VOUT = 15V, VIN 2.7V VOUT = 15V, VIN 3.2V VIN = 5V VIN = 3.6V VSHDN = 3.6V, No Switching VSHDN = 3.6V, Switching VSHDN = 0V Device ON Device OFF VSHDN = 0V or VSHDN = 5.5V ILoad = 0mA 1.205 10 1.230 10 0.6 1.6 93 0.8 0.8 5 5 1 1.2 1.85 1.255 1.5 0.5
Conditions
Min.
0.7 35 50
Typ.
1
Max.
Units
A mA mA
0.5 0.7 0.7 1.6 0.1 3.0 2
mA mA A V V nA V nA % MHz % mS mS A
Test Circuit
VIN CIN 4.7F 5 VIN 1 R1 CF 120pF 2.7V to 5.5V L 10H BAT54 COUT 4.7F VOUT
SW
150K
FAN5331
FB
3
R2 ON OFF 4 SHDN GND 2
13.4K
Figure 3. Test Circuit
3 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Typical Performance Characteristics
TA = 25C, Test Circuit Figure 3, unless otherwise noted.
Output Voltage vs Input Voltage
Maximum Load Current (mA)
14.98 14.96 14.94 14.92 14.90 14.88 14.86 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VIN(V) VIN(V) VIN(V) VIN(V) VIN(V) VIN(V) vs vs vs vs vs vs VOUT(V) at Iload=0mA VOUT(V), at load=10mA VOUT(V), at load=20mA VOUT(V) at Iload=30mA VOUT(V) at Iload=40mA VOUT(V) at Iload=50mA
Maximum Load Current vs Input Voltage
210 300 180 250 150 200 120 150 90 100 60 50 30 0 0 2.5 2.5 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 5.0 5.0 5.5 5.5
Output Voltage (V)
VO
UT
=
V 12
UT VO
=
V 15
1V =2
VOU
T
Input Voltage (V)
Input Voltage (V)
Efficiency vs Input Voltage
0.92 0.90 0.88 0.86
Feedback Voltage vs Ambient Temperature
1.25
IOUT = 15mA
Feedback Voltage (V)
1.24 1.23 1.22 1.21
Temperature (C) vs Vf (Vin=2.7V, Iload=15m A) Temperature (C) vs Vf (Vin=3.6V, Iload=15m A) Temperature (C) vs Vf (Vin=5.5V, Iload=15m A)
Efficiency
0.84 0.82 0.80 0.78 0.76 0.74 0.72 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VIN(V) VIN(V) VIN(V) VIN(V) VIN(V) vs vs vs vs vs Efficiency Efficiency Efficiency Efficiency Efficiency at at at at at Iload Iload Iload Iload Iload =10mA =20mA =30mA =40mA =50mA
-50
0
50
100
150
Input Voltage (V)
Ambient Temperature (C)
Supply Current vs Input Voltage
3.0
Switching Frequency vs Ambient Temperature
Switching Frequency (MHz)
IOUT = 15mA VOUT = 15V VIN = 3.6V
Supply Current (mA)
2.5 2.0 1.5 1.0 0.5 0.0 2.5 3.0 3.5 4.0 4.5
IOUT = 0mA
1.8
Switching
1.6
1.4
Non Switching
1.2
1.0 -40 -20 0 20 40 60 80 100 120 140
5.0
5.5
6.0
Input Voltage (V)
Ambient Temperature (C)
4 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Typical Performance Characteristics (Contd.)
TA = 25C, Test Circuit Figure 3, unless otherwise noted.
Startup After Enable
RL = 300
Line Transient Response
IOUT = 30mA VIN = 4.2V Tr = Tf = 10S VOUT = 15V
Input Voltage
VIN = 3V VOUT = 15V
(5V/div)
VIN = 3.2V
Output Voltage
+0.6V
(200mA/div)
-0.6V
Inductor Current= 0mA
Time (200s/div)
Time (100s/div)
Load Transient Response
(100mV/Div)
Output Power Spectral Density
VIN = 3.6V IOUT = 35mA
(10mA/Div)
Tr = Tf < 1S VOUT = 15V IOUT = 0 to 35mA
Time (20s/div)
5 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Block Diagram
SHDN 4 VIN 5
SW 1
Shutdown Circuitry
FB
+Over
Voltage
- Comp
1.15 x VREF
Thermal Shutdown
R FB 3 +
Error Amp
S
Ramp Generator Oscillator
+ Comp Current Limit Comparator -
R R S
Q
Driver
n
+
+ Amp Reference Soft-Start
0.05
2 GND
Figure 4. Block Diagram
Circuit Description
The FAN5331 is a pulse-width modulated (PWM) current-mode boost converter. The FAN5331 improves the performance of battery powered equipment by significantly minimizing the spectral distribution of noise at the input caused by the switching action of the regulator. In order to facilitate effective noise filtering, the switching frequency was chosen to be high, 1.6MHz. An internal soft start circuitry minimizes in-rush currents. The timing of the soft start circuit was chosen to reach 95% of the nominal output voltage within maximum 5mS following an enable command when VIN = 2.7V, VOUT = 15V, ILOAD = 35mA and COUT (EFFECTIVE) = 3.2F. The device architecture is that of a current mode controller with an internal sense resistor connected in series with the N-channel switch. The voltage at the feedback pin tracks the output voltage at the cathode of the external Schottky diode (shown in the test circuit). The error amplifier amplifies the difference between the feedback voltage and the internal bandgap reference. The amplified error voltage serves as a reference voltage to the PWM comparator. The inverting input of the PWM comparator consists of the sum of two components: the amplified control signal received from the 50m current sense resistor and the ramp generator voltage derived from the oscillator. The oscillator sets the latch, and the latch turns on the FET switch. Under normal operating conditions, the PWM comparator resets the latch and turns off the FET, thus terminating the pulse. Since the comparator input contains information about the output voltage and the control loop is arranged to form a negative feedback loop, the value of the peak inductor current will be adjusted to maintain regulation. Every time the latch is reset, the FET is turned off and the current flow through the switch is terminated. The latch can be
reset by other events as well. Over-current condition is monitored by the current limit comparator which resets the latch and turns off the switch instantaneously within each clock cycle.
Over-Voltage Protection
The voltage on the feedback pin is sensed by an OVP Comparator. When the feedback voltage is 15% higher than the nominal voltage, the OVP Comparator stops switching of the power transistor, thus preventing the output voltage from going higher.
Applications Information
Setting the Output Voltage
The internal reference is 1.23V (Typical). The output voltage is divided by a resistor divider, R1 and R2 to the FB pin. The output voltage is given by
R1 V OUT = V REF 1 + ------ R 2
According to this equation, and assuming desired output voltage of 15V, good choices for the feedback resistors are, R1=150k and R2=13.4k.
Inductor Selection
The inductor parameters directly related to device performances are saturation current and dc resistance. The FAN5331 operates with a typical inductor value of 10H. The lower the dc resistance, the higher the efficiency. Usually a trade-off between inductor size, cost and overall efficiency is needed to make the optimum choice.
6 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
The inductor saturation current should be rated around 1A, which is the threshold of the internal current limit circuit. This limit is reached only during the start-up and with heavy load condition; when this event occurs the converter can shift over in discontinuous conduction mode due to the automatic turn-off of the switching transistor, resulting in higher ripple and reduced efficiency. Some recommended inductors are suggested in the table below:
PCB Layout Recommendations
The inherently high peak currents and switching frequency of power supplies require careful PCB layout design. Therefore, use wide traces for high current paths and place the input capacitor, the inductor, and the output capacitor as close as possible to the integrated circuit terminals. The resistor divider that sets the output voltage should be routed away from the inductor to avoid RF coupling. A four layer PCB with at least one ground plane connected to the pin 2 of the IC is recommended. This ground plane acts as an electromagnetic shield to reduce EMI and parasitic coupling between components.
Inductor Value
10H 10H 10H
Vendor
Panasonic Murata Coilcraft
Part Number
ELL6GM100M LQS66SN100M03L DO1605T-103Mx
Comment
Lower Profile (1.6mm) Highest Efficiency Small Size
Table 1: Recommended Inductors
Capacitors Selection
For best performance, low ESR input and output capacitors are required. Ceramic capacitors in the range 4.7F to 10F, placed as close to the IC pins, are recommended for the lower input and output ripple. The output capacitor voltage rating should be according to the VOUT setting. A feed forward capacitor CF, is required for stability. The recommended value (R1 x CF) is around 18S. Some capacitors are suggested in the table below.
Figure 5. Recommended Layout
Application Examples
1. LED Driver
One or more serial LED strings can be driven with a constant current, set by the series resistor, given by
Capacitor Value
4.7F 4.7F
Vendor
Panasonic Murata
Part Number
ECJ3YB1C475K GRM31CR61C475
1.23V I LED = --------------R1
Table 2: Recommended Capacitors
Diode Selection
The external diode used for rectification is usually a Schottky diode. Its average forward current and reverse voltage maximum ratings should exceed the load current and the voltage at the output of the converter respectively. A barrier Schottky diode such as BAT54 is preferred, due to its lower reverse current over the temperature range. Care should be taken to avoid any short circuit of VOUT to GND, even with the IC disabled, since the diode can be instantly damaged by the excessive current.
VIN CIN
2.7V to 5.5V
L 10H
BAT54 COUT 4.7F
VOUT
4.7F 5 V
IN
SW
1
FAN5331
FB
3
ON OFF
4
SHDN
GND
2
R1
R2
Thermal Shutdown
When the die temperature exceeds 150C, a reset occurs and will remain in effect until the die cools to 130C, at that time the circuit will be allowed to restart.
Figure 6. Low Noise Boost LED Driver
7 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
LED Current vs Input Voltage (String Connected to FB Pin)
20.2
While the feedback loop tightly regulates VOUT, the negative output voltage (-VOUT) can supply a light load with a negative voltage. Nevertheless, the negative voltage depends on the changes of the load current in both -VOUT and +VOUT, as shown in the graph below.
LED Current (mA)
20.1 20.0
Negative Output Voltage vs Load Current
-18
Negative Output Voltage (V)
19.9 19.8 19.7 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
-15V/Unloaded
-16
-15V/10mA Load
-14
Input Voltage (V)
The feedback loop tightly regulates the current in the branch connected to FB pin, while the current in the other branch depends on the sum of the LED's forward voltages, VOUT and the ballast resistor. The input and the output ripple is less than 3mVRMS, for load currents up to 40mA. A Zener diode (VZ = 22V) connected between VOUT and GND can prevent the FAN5331 from being damaged by over-voltage, if the load is accidently disconnected during operation.
-12
-10 0 10 20 30 40 50
Load Current On Positive Output Side (mA)
2. Dual Boost Converter
A negative voltage can be provided by adding an external charge pump (C1, C2, D2, and D3).
C1 0.1F BAT54S D2 C2 D3 4.7F
-VOUT IOUT = 10mA
VIN CIN
2.7V to 5.5V
L 10H
BAT54
VOUT COUT I OUT = 50mA 4.7F R1 CF 120pF
D1
4.7F 5 VIN 1
SW
FAN5331
FB
3
R2 ON OFF
4
SHDN
GND
2
Figure 7. Dual () Boost Converter
8 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
Mechanical Dimensions
5-Lead SOT-23Package
B e c E H e1 D A A1 L
Symbol Min
A A1 B c D E e e1 H L .087 .004 0 .035 .000 .008 .003 .106 .059
Inches Max
.057 .006 .020 .010 .122 .071 .037 BSC .075 BSC .126 .024 10
Millimeters Min
.90 .00 .20 .08 2.70 1.50 .95 BSC 1.90 BSC 2.20 .10 0 3.20 .60 10
Notes
Max
1.45 .15 .50 .25 3.10 1.80
Ordering Information
Product Number
FAN5331
Package Type
5-Lead SOT23
Order Code
FAN5331SX
9 FAN5331 Rev. 1.0.1
www.fairchildsemi.com
FAN5331 High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.
ACExTM FAST ActiveArrayTM FASTrTM BottomlessTM FPSTM Build it NowTM FRFETTM CoolFETTM GlobalOptoisolatorTM CROSSVOLTTM GTOTM DOMETM HiSeCTM EcoSPARKTM I2CTM E2CMOSTM i-LoTM EnSignaTM ImpliedDisconnectTM FACTTM IntelliMAXTM FACT Quiet SeriesTM Across the board. Around the world.TM The Power Franchise Programmable Active DroopTM
DISCLAIMER
ISOPLANARTM LittleFETTM MICROCOUPLERTM MicroFETTM MicroPakTM MICROWIRETM MSXTM MSXProTM OCXTM OCXProTM OPTOLOGIC OPTOPLANARTM PACMANTM POPTM Power247TM PowerEdgeTM
PowerSaverTM PowerTrench QFET QSTM QT OptoelectronicsTM Quiet SeriesTM RapidConfigureTM RapidConnectTM SerDesTM SILENT SWITCHER SMART STARTTM SPMTM StealthTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6
SuperSOTTM-8 SyncFETTM TinyLogic TINYOPTOTM TruTranslationTM UHCTM UltraFET UniFETTM VCXTM WireTM
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life 1. Life support devices or systems are devices or support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Product Status Formative or In Design Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
Preliminary
First Production
No Identification Needed
Full Production
Obsolete
Not In Production
This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.
Rev. I16
10 FAN5331 Rev. 1.0.1
www.fairchildsemi.com

▲Up To Search▲

Price & Availability of FAN533105

	To Download FAN533105 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .