![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
w w ee SPECIFICATION FOR LCD MODULE Sh ta a D . w Model No. TM162B3BCU6 4U t om .c Prepared by: Checked by : Verified by : Approved by: w w .D w t a S a e h Date: Date: Date: Date: t e U 4 .c m o TIANMA MICROELECTRONICS CO., LTD S w w w .D ta a ee h 4U t om .c Ver. 1.0 REVISION RECORD Date 2003-1-23 Ver. Ver 1.0 Ref. Page. Revision No. Revision Item 1/22 1 General Specifications: 1.1 Display type: STN/YELLOW-GREEN mode 1.2 Display color*1: Display color: Bule-Black Background*2: YELLOW-GREEN 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 12:00 1.5 Driving Method: 1/16 Duty 1/5 Bias 1.6 LCD Operation Voltage: 3.3V 3.3V 1.7 VDD: 1.8 Backlight: LED 1.9 Controller: S6A0069X01-C0CX 1.10 Display Fonts: 5 X 7 Dots+Cursor 1.11 Data Transfer: 8 Bit Parallel 1.12Operating Temperature: 0ae ----+50ae Storage Temperature: -20ae ----+70ae 1.13 Outline Dimensions: Refer to outline drawing on next page 1.14 Dot Matrix: 16 Characters X 2 Line 1.15 Dot Size: 0.55X0.65(mm) 1.16 Dot Pitch: 0.6X0.7(mm) 1.17 Weight: about 100g *1 Color tone is slightly changed by temperature and driving voltage. *2 Color tone will be changed by backlight. 2/22 2 Outline Drawing 3/22 3 LCD Module Part Numbering System T M 162 B3 B C U 6 MODIFICATION CODE DISIGNATOR VIEWING DIRECTION U :12:00 BACKLIGHT TYPE C: TRANSFLECTIVE, LED BACKLIGHT LCD TYPE B:YELLOW GREEN STN MODULE SERIES MODULE TYPE 3 DIGITS INDICATING 16 CHARACTERS X 2 LINES T: TIANMA M: MODULE 4/22 4 Circuit Block Diagram 5/22 5 Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol VDDVSS VLCD Min. -0.3 -0.3 Max. 7.0 V 14.0 Unit Remark TOP 0 +50 ae No Condensation TST -20 +70 6/22 6 Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Supply Voltage (Logic) Supply Voltage (LCD Drive) Input Signal Voltage Symbol VDDVSS Min. 2.7 Typ. 3.3 Max. 5.0 Unit V VDDVEE 0.7VDD VIH -0.3 VIL 3.3 - V - VDD+0.3 V - 0.2 VDD V Supply current (Logic) Supply current (LCD Drive) Supply current (LED) IDD IEE ILED - 1.3 0.5 - 200 mA mA mA 7/22 6.2 Interface Signals Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Symbol VDD VSS V0 RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 Level Description 3.3V 0V 0V H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L Power supply voltage for logic (+3.3V) Gound Voltage Level for LCD Contrast Adjust Instruction/Data Selects Regisers Select Read or Write Enable Input Data bit0 Data bit1 Data bit2 Data bit3 Data bit4 Data bit5 Data bit6 Data bit7 8/22 6.3 Interface Timing Chart AC Characteristics(VDD=2.7V~5.5V,Ta=-30~+85 7 0RGH :ULWHy0RGH o5HIHUyWRy)LJco 5HDGy0RGH o5HIHUyWRy)LJaeo &KDUDFWHULVWLF (y&\FOHy7LPH (y5LVHyiy)DOOy7LPH (y3XOVHy:LGWKyo+LJKny/RZo 5i:yDQGy56y6HWXSy7LPH 5i:yDQGy56y+ROGy7LPH 'DWDy6HWXSy7LPH 'DWDy+ROGy7LPH (y&\FOHy7LPH (y5LVHyiy)DOOy7LPH (y3XOVHy:LGWKyo+LJKny/RZo 5i:yDQGy56y6HWXSy7LPH 5i:yDQGy56y+ROGy7LPH 'DWDy2XWSXWy'HOD\y7LPH 'DWDy+ROGy7LPH 6\PERO WF W5nW) WZ WVXi W+i WVXe W+e WF W5nW) WZ WVX W+ W' W'+ 0LQi eii eei ei ii ai ii eii eei ei ii e 7\Si 0D[i ei ei iei QV QV 8QLW 9/22 56 5i: ( '%ia'%ae 56 5i: ( '%ia'%ae 9 , +i 9 , /i W68i 9 , /i 9 , +i 9 , /i WU 9 , +i 9 , /i W Ki 9 , /i WI W Ke 9 , +i 9 , /i 9 , /i WZ 9 , +i 9 , /i W Ki W 68e 9DOLG 'DWD W& )LJXUHycyiyy:ULWHy0RGHy7LPLQJy'LDJUDP 9,+i 9,/i 9,+i W68 WK 9 , +i WZ 9 , +i 9 , /i 9 , +i 9 , /i 9,+i 9,/i WK WI 9,/i 9,+i 9,/i WU W' W' + 9DOLG 'DWD W& )LJXUHyaeyiyy5HDGy0RGHy7LPLQJy'LDJUDP 10/22 6.4 Instruction Code yy,QVWUXFWLRQy7DEOH ,QVWUXFWLRQy&RGH ([HFXWLRQy ,QVWUXFWLRQ 'HVFULSWLRQ WLPHyoIRVF y 56 5i: '%ae '%c '%e '%e '%e '%e '%i '%i eaeiyN+]o &OHDU y:ULWHy|ei+yWRy''5$0yDQGyVHWy i i i i i i i i i i iieeyPVy 'LVSOD\ y''5$0yDGGUHVVyWRy|ii+yIURPy$& y6HWy''5$0yDGGUHVVyWRy|ii+y yIURPy$&yDQGyUHWXUQyFXUVRUyWRyLWV 5HWXUQy i i i i i i i i i yRULJLQDOySRVLWLRQyLIyVKLIWHGiy iieeyPV +RPH y7KHyFRQWHQWVyRIy''5$0yDUHyQRWy yFKDQJHGi (QWU\y0RGHy y$VVLJQyFXUVRUyPRYLQJyGLUHFWLRQy i i i i i i i i ,i' 6+ eayPV 6HWy yDQGyHQDEOHyWKHyVKLIWyRIyHQWLUHyGLVSOD\iy y6HWyGLVSOD\o'onyFXUVRUo&ony 'LVSOD\y21i eayPV i i i i i i i ' & % yDQGyEOLQNLQJyRIyFXUVRUo%oyRQiRIIy 2))y&RQWURO yFRQWUROyELWi y6HWyFXUVRUyPRYLQJyDQGyGLVSOD\y &XUVRUyRU eayPV i i i i i i 6i& 5i/ yVKLIWyFRQWUROyELWnyDQGyWKHyGLUHFWLRQny y'LVSOD\y 6KLIW yZLWKRXWyFKDQJLQJyRIy''5$0yGDWDiy y6HWyLQWHUIDFHyGDWDyOHQJWKyo'/ay yaELWieELWonyQXPEHUVyRIyGLVSOD\yOLQH eayPV i i i i '/ 1 ) y )XQFWLRQy6HW i yo1ayeOLQHiiOLQHoyDQGnyGLVSOD\ yIRQWyW\SHyo)aeuiiGRWVieuayGRWVo y6HWy&*5$0yDGGUHVVyLQyDGGUHVVy 6HWy&*5$0y i i i i $&e $&e $&e $&e $&i $&i eayPV yFRXQWHUi $GGUHVV 6HWy''5$0y y6HWy''5$0yDGGUHVVyLQyDGGUHVVy eayPV i i i $&c $&e $&e $&e $&e $&i $&i $GGUHVV yFRXQWHUi y:KHWKHUyGXULQJyLQWHUQDOyRSHUDWLRQ 5HDGy%XV\y yRUyQRWyFDQyEHyNQRZQyE\yUHDGLQJy%)iy i i %) $&c $&e $&e $&e $&e $&i $&i iyPV )ODJyDQGy y7KHyFRQWHQWVyRIyDGGUHVVyFRXQWHU $GGUHVV yFDQyDOVRyEHyUHDGi :ULWHy'DWDyWRy y:ULWHyGDWDyLQWRyLQWHUQDOy5$0y i i 'ae 'c 'e 'e 'e 'e 'i 'i eeyPV 5$0 yo''5$0i&*5$0oi 5HDGy'DWDy y5HDGyGDWDyIURPyLQWHUQDOy5$0y i i 'ae 'c 'e 'e 'e 'e 'i 'i eeyPV IURPy5$0 yo''5$0i&*5$0oi yyyyyyyyyyyyoy||ayGRQ(c)WyFDUH 127(ay:KHQyDQy038ySURJUDPyZLWKyFKHFNLQJyWKHy%XV\y)ODJo'%aeoyLVyPDGHnyLWyPXVWyEHyQHFHVVDU\yiie)RVFyLV yyyyyyyyyyyyyQHFHVVDU\yIRUyH[HFXWLQJyWKHyQH[WyLQVWUXFWLRQyE\yWKHyIDOOLQJyHGJHyRIyWKHyo(oyVLJQDOyDIWHUyWKHy%XV\y)ODJyo'%aeoy yyyyyyyyyyyyyJRHVyWRy|/RZiy 11/22 6.5 Character generator ROM(S6A0069X01-COCX) 12/22 7 Optical Characteristics 7.1 Optical Characteristics Item Viewing Angle Symb |x E y |E Ta=25ae Condition Cr>2 |y=0a E |x=0a E x=0a |E y=0a |E x=0a |E Min. Typ. Max. 20 Unit Deg -35 ~ -30 ~ _ _ 4.0 30 _ 250 250 Contrast Ratio Respon Turn on se Time Turn off Cr Ton Toff ms |E y=0a _ 13/22 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top Bottom 7.2.2 Definition of Contrast Ratio Bottom Contrast Ratio = B2/B1 = unselected state brightness selected state brightness Measuring Conditions: 1) Ambient Temperature: 25ae; 7.2.3 Definition of Response time 2) Frame frequency: 64Hz Turn on time: t on = t d + t r Turn off time: t off = t d + t f Measuring Condition: 1) Operating Voltage: 3.3V 2) Frame frequency: 64Hz 14/22 8 Reliability 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage 3 High Temperature Operation Low Temperature Operation Content of Test Endurance test applying the high storage temperature for a long time Endurance test applying the low storage temperature for a long time Endurance test applying the electric stress (voltage | current) and the thermal stress to the element for a long time Endurance test applying the electric stress under low temperature for a long time Ta=25ae Test condition 70ae ,96H Restore 4H -20ae ,96H Restore 4H 50ae 96H 0ae 96H 40ae96H , 90%RH Restore 4H 4 5 Endurance test applying the high High Temperature temperature and high humidity /Humidity Storage storage for a long time 6 Temperature Cycle Endurance test applying the low and high temperature cycle -20ae /70ae -20 ae u70 ae u25 ae u25ae u u u 10 cycles 30min 5min 30min 5min u(c)(c)(c)(c)(c)(c)(c)(c)(c)(c)(c)(c)u Restore 4H 1 cycle Endurance test applying the vibration during transportation Endurance test applying the shock during transportation Endurance test applying the atmospheric pressure during transportation by air 10Hz~150Hz, 50m/s2, 40min Half- sine wave, 100m/s2, 11ms 40kPa 16H Restore 2H 7 Vibration Test (package state) Shock Test (package state) Atmospheric Pressure Test 8 9 15/22 8.2 Failure Judgment Criterion Criterion Item Basic Specification Electrical specification Mechanical Specification Optical Characteristic Note Remark vvvvv Test Item No. Failure Judgement Criterion 123456789 v v v v v v v v Out of the basic Specification Out of the electrical specification vv Out of the mechanical specification v Out of the optical specification v v vvvv v For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification 16/22 9 QUALITY LEVEL Examination or Test At Ta=25ae (unless otherwise stated) Min. Inspection Max. Unit IL AQL Under normal Major External illumi-nation and eyesight 1.0 Visual condition, the dis-tance See Appendix A II Minor Inspection between eyes and LCD 2.5 is 25cm. Under normal Major Display illumi-nation and eyesight 1.0 See Appendix B II Defects condition, display on Minor inspection. 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828 17/22 10 Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 18/22 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0ae40ae Relatively humidity: U 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 19/22 Appendix A Inspection items and criteria for appearance defects Items Leakage Rainbow Wrong polarizer attachment Polarizer Bubble between polarizer and glass Scratches of polarizer Black spot (in viewing area) Contents Criteria Not permitted According to the limit specimen Not permitted Not counted <0.3mm Max. 3 defects allowed 0.3mmU 0.5mm According to the limit specimen Not counted Max. 3 spots allowed X<0.2mm X=(a+b)/2 0.2mmUU X 0.5mm Max. 3 spots (lines) allowed Black line (in viewing area) Not counted Max. 3 lines allowed 0.02mmU 0.05mm aU bU 2.0mm a<0.02mm Progressive cracks Not permitted 20/22 Appendix B Inspection items and criteria for display defects Items Contents Critera Not permitted Not permitted Not permitted According to the limit specimen According to the limit specimen Not counted X<0.1mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Not counted A<0.1mm Max.2 dots allowed 0.1mmU 0.2mm AU D<0.25mm Max.3 dots allowed 0.1mmU 0.2mm XU Max.3 dots allowed Open segment or open common Short Wrong viewing angle Contrast radio uneven Crosstalk Black spot (in viewing area) Not counted X<0.1mm X=(a+b)/2 Max.3 spots allowed 0.1mmU 0.2mm XU Max.3 spots (lines) allowed Black line (in viewing area) Not counted a<0.02mm Max.3 lines allowed 0.02mmU 0.05mm aU bU 0.5mm 21/22 Appendix B Inspection items and criteria for display defects (continued) Items Content Critera Not counted x1/4 0.1mm x=(a+b)/2 Max. 2 defects allowed 0.1mmU 0.2mm xU Not counted a1/4 0.1mm Transformation of segment Max. 1 defects allowed 0.1mmU 0.2mm aU D>0 Max.3 defects allowed Max.2 defects allowed 0.8WU 1.2W aU a=measured value of width W=nominal value of width 22/22 |
Price & Availability of TM162B3BCU6
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |