View UPD5713TK-E2-A_457254.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRELIMINARY DATA SHEET CMOS INTEGRATED CIRCUIT
uPD5713TK
WIDE BAND SPDT SWITCH
DESCRIPTION
The uPD5713TK is a CMOS MMIC for wide-band SPDT Single Pole Double Throw which were designed for mobile communications, wireless communications and another general-purpose RF switching application. This device can operate frequency from 0.05GHz to 2.5GHz,, having the low insertion loss and high isolation. This device is housed in a 6-pin lead-less minimold package 1511 . And this package is able to high-density surface mounting.
FEATURES
Supply Voltage Switch Control Voltage Low Insertion Loss : VDD = 1.8V to 3.3V 2.8V TYP. : Vcont H = 1.8V to 3.3V 2.8V TYP. : Vcont L = -0.2 to +0.4V 0V TYP. : LINS1 = 0.6dB TYP.@ f = 0.05 to 1.0GHz, VDD = 2.8V, Vcont = 2.8V/0V : LINS2 = 0.8dB TYP.@ f = 1.0 to 2.0GHz, VDD = 2.8V, Vcont = 2.8V/0V : LINS3 = 0.95dB TYP.@ f = 2.0 to 2.5GHz, VDD = 2.8V, Vcont = 2.8V/0V : ISL1 = 32.5dB TYP. @ f = 0.05 to 1.0GHz, VDD = 2.8V, Vcont = 2.8V/0V : ISL2 = 25dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.8V, Vcont = 2.8V/0V : ISL3 = 22.5dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.8V, Vcont = 2.8V/0V : Pin 1dB = +21.0dBm TYP.@ f = 1.0GHz, VDD = 2.8V, Vcont = 2.8V/0V Pin 0.1dB = +17.0dBm TYP.@ f = 1.0GHz, VDD = 2.8V, Vcont = 2.8V/0V : 6-pin lead-less minimold package 1.5 1.1 0.55 mm
High Isolation
Handling Power High-density surface mounting
APPLICATION
Mobile communications Wireless communications Another general-purpose RF switching applications
ORDERING INFORMATION
Part Number UPD5713TK-E2-A Package 6-pin lead-less minimold 1511 Marking C3Q Supplying Form Embossed tape 8mm wide Pin 1,6 face the perforation side of the tape Qty 5 kpcs / reel
Remark To order evaluation samples, contact your nearby sales office. Part number for sample order : uPD5713TK-A
Caution Electro-static sensitive devices
The information in this document is being issued in advance of the production cycle for device. The parameters for the device may change before final production or NEC Compound Semiconductor Devices, at its own discretion, may withdraw the device prior to its production.
Document No. PG*****EJWV1PDS ( 1st edition ) Date Published February 2006 CP(K)
uPD5713TK
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No. 1 1 2 3 6 5 4 1 2 3 6 5 4 6 5 4 1 2 3 2 3 4 5 6 Pin Name OUTPUT1 GND OUTPUT2 Vcont INPUT VDD
Top View
Top View
Bottom View
SW TRUTH TABLE
Vcont Low High INPUT-OUTPUT1 OFF ON INPUT-OUTPUT2 ON OFF
ASOLUTE MAXIMUM RATINGS
Parameter Supply Voltage Switch Control Voltage Voltage Difference Input Power Power Dissipation Operating Ambient Temperature Storage Temperature
Note. Mounted on double-sided copper-clad 50 50 1.6mm epoxy glass PWB
RECOMMENDED OPERATING RANGE
Parameter Supply Voltage Switch Control Voltage H Switch Control Voltage L Note. VDD-0.4V Vcont(H) Symbol VDD Vcont Vcont VDD+0.2V
H L
C3Q
Unless otherwise specified, TA = +25
Symbol VDD Vcont Vcont - VDD Pin PD TA Tstg Ratings -0.5 to +4.6 -0.5 to +4.6 +0.5 +23 203Note -45 to +85 -65 to +150 Unit V V V dBm mW
Unless otherwise specified, TA = +25
MIN. +1.8 +1.8 -0.2 TYP. +2.8 +2.8 0 MAX. +3.6 +3.6 +0.4 Unit V V V
2
Preliminary Data Sheet
uPD5713TK
ELECTRICAL CHARACTERISTICS Unless otherwise specified, TA = +25 , VDD = 2.8V, Vcont(H) = 2.8V, Vcont(L) = 0V, Pin = 0dBm
Parameter Insertion Loss1 Insertion Loss2 Insertion Loss3 Isolation1 Isolation2 Isolation3 Input Return Loss Output Return Loss 0.1dB Loss Compression Input PowerNote 1dB Loss Compression Input PowerNote Supply Current Switch Control Current Switch Control Speed Symbol LINS1 LINS2 LINS3 ISL1 ISL2 ISL3 RLin RLout Pin Pin
0.1dB
Test Conditions f = 0.05 to 1.0GHz f = 1.0 to 2.0GHz f = 2.0 to 2.5GHz f = 0.05 to 1.0GHz f = 1.0 to 2.0GHz f = 2.0 to 2.5GHz f = 0.05 to 2.5GHz f = 0.05 to 2.5GHz f = 1.0GHz f = 1.0GHz No Signal No Signal f = 1.0GHz
MIN. 30 22 20 13 13 +13.0 -
TYP. 0.6 0.8 0.95 32.5 25 22.5 17 17 +17.0 +21.0 0.01 0.01 30
MAX. 0.8 1.0 1.2 1.0 1.0 100
Unit dB dB dB dB dB dB dB dB dBm dBm uA uA nS
1dB
IDD Icont tSW
Note. Pin 0.1dB or Pin 1dB are measured the input power level when the insertion loss increases more 0.1dB or 1dB than that of linear range.
Preliminary Data Sheet
3
uPD5713TK
EVALUATION CIRCUIT
1000pF 4 Vcont DC Block 1000pF 5 INPUT 6 VDD
DC Block 1000pF OUTPUT2 3 2 OUTPUT1 1
1000pF
DC Block 1000pF
Note1 : This IC has pull down resistance between RF line and GND, which fixes electric potential of RF line to 0V, then the IC cannot be used for DC switching. Note2 : If an external DC voltage is not present on RF lines, the DC blocking capacitors are not needed.
4
Preliminary Data Sheet
uPD5713TK
PACKAGE DIMENSIONS 6-PIN LEAD-LESS MINIMOLD 1511 UNIT mm
Preliminary Data Sheet
5
uPD5713TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature package surface temperature Time at peak temperature Time at temperature of 220 or higher Preheating time at 120 to 180 Maximum number of reflow processes Maximum chlorine content of rosin flux mass Peak temperature package surface temperature Time at temperature of 200 or higher Preheating time at 120 to 150 Maximum number of reflow processes Maximum chlorine content of rosin flux mass Peak temperature molten solder temperature Time at peak temperature Preheating temperature package surface temperature Maximum number of reflow processes Maximum chlorine content of rosin flux mass Peak temperature pin temperature Soldering time per side of device Maximum chlorine content of rosin flux : 260 or below : 10 seconds or less : 60 seconds or less : 120 30 seconds : 3 times : 0.2 Wt. or below : 215 or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2 Wt. or below : 260 or below : 10 seconds or less : 120 or below : 1 time : 0.2 Wt. or below : 350 or below : 3 seconds or less : 0.2 Wt. or below Condition Symbol IR260
VPS
VP215
Wave soldering
WS260
Partial Heating
HS350
mass
Caution Do not use different soldering methods together
except for partial heating .
6
Preliminary Data Sheet
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of UPD5713TK-E2-A

	To Download UPD5713TK-E2-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .