 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DG444, DG445 Data Sheet June 1999 File Number 3586.5 Monolithic, Quad SPST, CMOS Analog Switches The DG444 and DG445 monolithic CMOS analog switches are drop-in replacements for the popular DG211 and DG212 series devices. They include four independent single pole single throw (SPST) analog switches and TTL and CMOS compatible digital inputs. These switches feature lower analog ON resistance (<85) and faster switch time (tON <250ns) compared to the DG211 and DG212. Charge injection has been reduced, simplifying sample and hold applications. The improvements in the DG444 series are made possible by using a high voltage silicon-gate process. An epitaxial layer prevents the latch-up associated with older CMOS technologies. The 44V maximum voltage range permits controlling 20V signals when operating with 20V power supplies. The four switches are bilateral, equally matched for AC or bidirectional signals. The ON resistance variation with analog signals is quite low over a 5V analog input range. The switches in the DG444 and DG445 are identical, differing only in the polarity of the selection logic. Features * ON Resistance (Max) . . . . . . . . . . . . . . . . . . . . . . . . . 85 * Low Power Consumption (PD) . . . . . . . . . . . . . . . . <35W * Fast Switching Action - tON (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250ns - tOFF (Max, DG444) . . . . . . . . . . . . . . . . . . . . . . . 140ns * Low Charge Injection * Upgrade from DG211/DG212 * TTL, CMOS Compatible * Single or Split Supply Operation Applications * Audio Switching * Battery Operated Systems * Data Acquisition * Hi-Rel Systems * Sample and Hold Circuits * Communication Systems * Automatic Test Equipment Pinout DG444, DG445 (PDIP, SOIC) TOP VIEW IN1 D1 S1 VGND S4 D4 IN4 1 2 3 4 5 6 7 8 16 IN2 15 D2 14 S2 13 V+ 12 VL 11 S3 10 D3 9 IN3 Ordering Information PART NUMBER DG444DJ DG444DY DG445DJ DG445DY TEMP. RANGE (oC) -40 to 85 -40 to 85 -40 to 85 -40 to 85 PACKAGE 16 Ld PDIP 16 Ld SOIC 16 Ld PDIP 16 Ld SOIC PKG. NO. E16.3 M16.15 E16.3 M16.15 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright (c) Intersil Corporation 1999 DG444, DG445 Functional Diagrams DG444 S1 IN1 D1 S2 IN2 D2 S3 IN3 D3 S4 IN4 D4 SWITCHES SHOWN FOR LOGIC "1" INPUT IN4 D4 IN3 D3 S4 IN2 D2 S3 IN1 D1 S2 Pin Descriptions DG445 S1 PIN 1 2 3 4 5 6 7 8 9 10 11 12 SYMBOL IN1 D1 S1 VGND S4 D4 IN4 IN3 D3 S3 VL V+ S2 D2 IN2 DESCRIPTION Logic Control for Switch 1 Drain (Output) Terminal for Switch 1 Source (Input) Terminal for Switch 1 Negative Power Supply Terminal Ground Terminal (Logic Common) Source (Input) Terminal for Switch 4 Drain (Output) Terminal for Switch 4 Logic Control for Switch 4 Logic Control for Switch 3 Drain (Output) Terminal for Switch 3 Source (Input) Terminal for Switch 3 Logic Reference Voltage. Positive Power Supply Terminal (Substrate) Source (Input) Terminal for Switch 2 Drain (Output) Terminal for Switch 2 Logic Control for Switch 2 TRUTH TABLE LOGIC 0 1 VIN 0.8V 2.4V DG444 ON OFF DG445 13 14 OFF 15 ON 16 Schematic Diagram V+ (One Channel) S VL VV+ INX D GND V- 2 DG444, DG445 Absolute Maximum Ratings V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V VL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND - 0.3V) to (V+) + 0.3V Digital Inputs, VS , VD (Note 1). . . . . (V-) -2V to (V+) + 2V or 30mA, Whichever Occurs First Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA Thermal Information Thermal Resistance (Typical, Note 2) JA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Maximum Junction Temperature (Plastic Packages) . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V (Max) Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max) Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min) Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20ns CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Signals on SX , DX , or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. 2. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VL = 5V, VIN = 2.4V, 0.8V (Note 3), Unless Otherwise Specified TEST CONDITIONS TEMP (oC) (NOTE 4) MIN (NOTE 5) TYP (NOTE 4) MAX UNITS PARAMETER DYNAMIC CHARACTERISTICS Turn-ON Time, tON Turn-OFF Time, tOFF DG444 DG445 Charge Injection, Q (Figure 2) OFF Isolation (Figure 4) Crosstalk (Channel-to-Channel) (Figure 3) Source OFF Capacitance, CS(OFF) Drain OFF Capacitance, CD(OFF) Channel ON Capacitance, CD(ON) + CS(ON) DIGITAL INPUT CHARACTERISTICS Input Current VIN Low, IIL Input Current VIN High, IIH ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG Drain-Source ON Resistance, rDS(ON) Source OFF Leakage Current, IS(OFF) RL = 1k, CL = 35pF, VS = 10V (Figure 1) 25 - 120 250 ns 25 25 CL = 1nF, VG = 0V, RG = 0 RL = 50, CL = 5pF, f = 1MHz 25 25 25 f = 1MHz, VANALOG = 0 (Figure 5) 25 25 25 - 110 160 -1 60 -100 4 4 16 140 210 - ns ns pC dB dB pF pF pF VIN Under Test = 0.8V, All Others = 2.4V VIN Under Test = 2.4V, All Others = 0.8V Full Full -0.5 -0.5 -0.00001 0.00001 0.5 0.5 A A Full IS = 10mA, VD = 8.5V, V+ = 13.5V, V- = -13.5V V+ = 16.5V, V- = -16.5V, VD = 15.5V, VS = 15.5V 25 Full 25 85 -15 -0.5 -5 50 0.01 - 15 85 100 0.5 5 V nA nA 3 DG444, DG445 Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VL = 5V, VIN = 2.4V, 0.8V (Note 3), Unless Otherwise Specified (Continued) TEST CONDITIONS V+ = 16.5V, V- = -16.5V, VD = 15.5V, VS = 15.5V V+ = 16.5V, V- = -16.5V, VS = VD , = 15.5V TEMP (oC) 25 85 25 85 (NOTE 4) MIN -0.5 -5 -0.5 -10 (NOTE 5) TYP 0.01 0.08 (NOTE 4) MAX 0.5 5 0.5 10 UNITS nA nA nA nA PARAMETER Drain OFF Leakage Current, ID(OFF) Channel ON Leakage Current, ID(ON) + IS(ON) POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ V+ = 16.5V, V- = -16.5V, VIN = 0V or 5V 25 85 25 85 -1 -5 -1 -5 0.001 -0.0001 0.001 -0.001 - 1 5 1 5 - A A A A A A A A Negative Supply Current, I- Logic Supply Current, IL 25 85 Ground Current, IGND 25 85 Electrical Specifications (Single Supply) Test Conditions: V+ = 12V, V- = 0V, VL = 5V, VIN = 2.4V, 0.8V (Note 3), Unless Otherwise Specified TEST CONDITIONS TEMP (oC) (NOTE 4) MIN (NOTE 5) TYP (NOTE 4) MAX UNITS PARAMETER DYNAMIC CHARACTERISTICS Turn-ON Time, tON Turn-OFF Time, tOFF Charge Injection, Q (Figure 2) ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG Drain-Source ON Resistance, rDS(ON) RL = 1k, CL = 35pF, VS = 8V (Figure 1) CL = 1nF, VG = 6V, RG = 0 25 25 25 - 300 60 2 450 200 - ns ns pC Full IS = -10mA, VD = 3V, 8V V+ = 10.8V, VL = 5.25V 25 Full 0 - 100 - 12 160 200 V POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ V+ = 13.2V, VIN = 0V or 5V, VL = 5.25V 25 Full 25 Full Logic Supply Current, IL 25 Full Ground Current, IGND 25 Full NOTES: 3. VIN = input voltage to perform proper function. 4. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 5. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. -1 -5 -1 -5 0.001 -0.0001 0.001 -0.001 1 5 1 5 A A A A A A A A Negative Supply Current, I- 4 DG444, DG445 Test Circuits and Waveforms VO is the steady state output with the switch on. Feedthrough via switch capacitance may result in spikes at the leading and trailing edge of the output waveform. 3V LOGIC INPUT 50% 0V tOFF SWITCH INPUT VS VO SWITCH OUTPUT 0V tON 80% 80% LOGIC INPUT 3V tr < 20ns tf < 20ns SWITCH INPUT S1 IN1 RL GND VCL VL V+ D1 VO NOTE: Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. MEASUREMENT POINTS Repeat test for Channels 2, 3 and 4. For load conditions, see Specifications. CL includes fixture and stray capacitance. RL V O = V S ----------------------------------R L + r DS ( ON ) FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES SWITCH OUTPUT VO VL RG V+ D1 VO INX (DG444) OFF ON OFF VG V- CL INX (DG445) OFF ON Q = VO x CL VIN = 3V OFF GND FIGURE 2A. MEASUREMENT POINTS FIGURE 2. CHARGE INJECTION FIGURE 2B. TEST CIRCUIT V+ C +15V C V+ +15V SIGNAL GENERATOR 10dBm VS VD 50 SIGNAL GENERATOR 10dBm VS 0V, 2.4V IN1 IN2 0V, 2.4V VD RL INX 0V, 2.4V ANALYZER RL VD C GND V-15V NC ANALYZER GND V- C -15V FIGURE 3. CROSSTALK TEST CIRCUIT FIGURE 4. OFF ISOLATION TEST CIRCUIT 5 DG444, DG445 Test Circuits and Waveforms (Continued) +15V C V+ VS INX IMPEDANCE ANALYZER VD f = 1MHz 0V, 2.4V GND V-15V C FIGURE 5. SOURCE/DRAIN CAPACITANCES TEST CIRCUIT Application Information FET INPUT OP AMP 3 2 +5V 12 2 GAIN1 AV = 1 GAIN2 AV = 10 GAIN3 AV = 20 GAIN4 AV = 100 1 15 16 10 9 7 8 6 R4 1k DG444 OR DG445 VGND 4 -15V 5 11 R3 4k 14 GND VR2 5k VL +15V + VIN - 7 6 4 +15V -15V 13 V+ 3 VOUT +5V VL +15V +5V +15V V+ +15V VOUT 10k 1/ DG444 4 R1 90k 0V 0V VIN FIGURE 7. LEVEL SHIFTER GAIN ERROR IS DETERMINED ONLY BY THE RESISTOR TOLERANCE, OP AMP OFFSET AND CMRR WILL LIMIT ACCURACY OF CIRCUIT R1 + R2 + R3 + R4 V OUT --------------- = ------------------------------------------------ = 100 V IN R4 WITH SW4 CLOSED FIGURE 6. PRECISION WEIGHTED RESISTOR PROGRAMMABLE GAIN AMPLIFIER 6 DG444, DG445 Typical Performance Curves 105 4 IL , I+, I-, IGND (nA) 104 103 3 VIN (V) 102 10 -(I-) 1 0.1 0.01 0 0 4 8 12 SUPPLY VOLTAGE (V) 16 20 0.001 -55 IL 0 50 TEMPERATURE (oC) 100 125 I+, IGND 2 VL = 5V 1 VL = 7V FIGURE 8. SWITCHING THRESHOLD vs SUPPLY VOLTAGE FIGURE 9. SUPPLY CURRENT vs TEMPERATURE 105 104 103 102 rDS(ON) () IIN (pA) 80 70 60 50 40 30 20 0oC -40oC 85oC 25oC V+ = +15V V- = -15V 10 1 10 0.1 -55 0 50 TEMPERATURE (oC) 100 125 0 -15 0 VD (V) 15 FIGURE 10. INPUT CURRENT vs TEMPERATURE FIGURE 11. rDS(ON) vs VD AND TEMPERATURE 140 120 100 80 (dB) 60 40 OFF ISOLATION CROSSTALK 50 40 30 20 Q (pC) 10 0 -10 CL = 10nF V+ = +15V V- = -15V CL = 1nF 20 0 100 V+ = +15V V- = -15V PGEN = 10dBm 1K 10K 100K 1M 10M -20 -30 -10 FREQUENCY (Hz) 0 VS (V) 10 FIGURE 12. CROSSTALK REJECTION AND OFF ISOLATION vs FREQUENCY FIGURE 13. CHARGE INJECTION vs SOURCE VOLTAGE 7 DG444, DG445 Typical Performance Curves 25 V+ = +15V V- = -15V 20 CS(ON) + CD(ON) CS , D (pF) IS , ID (pA) 15 0 (Continued) 20 IS(OFF) , ID(OFF) -20 -40 IS(ON) + ID(ON) 10 -60 5 CS(OFF) , CD(OFF) -80 V+ = +15V V- = -15V FOR I(OFF) , VD = -VS 0 -15 -10 -5 0 VA (V) 5 10 15 -100 -15 -10 -5 0 VS , VD (V) 5 10 15 FIGURE 14. SOURCE/DRAIN CAPACITANCE vs ANALOG VOLTAGE FIGURE 15. LEAKAGE CURRENTS vs ANALOG VOLTAGE 150 160 V+ = +15V V- = -15V 140 120 tON, tOFF (ns) 100 80 60 40 20 2 3 VIN (V) 4 5 0 2 3 VIN (V) 4 5 tOFF tON, tOFF (ns) tON 100 tON V+ = +15V, V- = -15V VL = 5V tOFF 50 FIGURE 16. SWITCHING TIME vs INPUT VOLTAGE (DG444) 160 140 tON 120 tON, tOFF (ns) 100 80 60 40 20 10 12 14 16 18 SUPPLY VOLTAGE (V) 20 22 FIGURE 17. SWITCHING TIME vs INPUT VOLTAGE (DG445) 160 VL = 5V 140 120 tON, tOFF (ns) 100 80 60 40 20 10 12 14 16 18 20 22 SUPPLY VOLTAGE (V) tON tOFF tOFF FIGURE 18. SWITCHING TIME vs POWER SUPPLY VOLTAGE (DG444) FIGURE 19. SWITCHING TIME vs POWER SUPPLY VOLTAGE (DG445) 8 DG444, DG445 Typical Performance Curves 400 V+ = +12V, V- = 0V VL = 5V 300 tON, tOFF (ns) tON, tOFF (ns) tON 400 tON (444) 300 tON (445) 200 (Continued) 500 V- = 0V, VL = 5V 200 100 tOFF 100 tOFF (445) tOFF (444) 0 2 3 VIN (V) 4 5 0 8 10 12 14 16 18 POSITIVE SUPPLY (V) 20 22 FIGURE 20. SWITCHING TIME vs INPUT VOLTAGE (DG444) (SINGLE 12V SUPPLY) 30 V+ = 12V V- = 0V FIGURE 21. SWITCHING TIMES vs SINGLE SUPPLY VOLTAGE 10 IS(OFF) , ID(OFF) 0 20 -10 10 CL = 10nF CL = 1nF 0 -30 IS , ID (pA) Q (pC) -20 IS(ON) + ID(ON) V+ = +12V V- = 0V FOR ID , VS = 0 FOR IS, VD = 0 0 6 VS , VD (V) 12 -10 0 4 VS (V) 8 -40 FIGURE 22. CHARGE INJECTION vs SOURCE VOLTAGE (SINGLE 12V SUPPLY) 20 V+ = +12V V- = 0V FIGURE 23. SOURCE/DRAIN LEAKAGE CURRENTS (SINGLE 12V SUPPLY) CS(ON) + CD(ON) 15 CS , D (pF) 10 5 CS(OFF) , CD(OFF) 0 0 6 VA (V) 12 FIGURE 24. SOURCE/DRAIN CAPACITANCE vs ANALOG VOLTAGE (SINGLE 12V SUPPLY) 9 DG444, DG445 Die Characteristics DIE DIMENSIONS: 2160m x 1760m x 485 METALLIZATION: Type: SiAl Thickness: 12kA 1kA PASSIVATION: Type: Nitride Thickness: 8kA 1kA WORST CASE CURRENT DENSITY: 9.1 x 104 A/cm2 Metallization Mask Layout DG444, DG445 D1 (2) IN1 (1) IN2 (16) (15) D2 S1 (3) (14) S2 V- (4) (13) V+ SUBSTRATE GND (5) (12) VL S4 (6) (11) S3 (7) D4 (8) IN4 (9) IN3 (10) D3 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 10 |
Price & Availability of DG445
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |