|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ICs for Mobile Communication AN6091SA Quadrature modulation IC for mobile communications I Overview The AN6091SA is a quadrature modulation IC for 1.5 GHz band digital cellular telephone, and incorporates a phase shifter, up-mixer and APC function as well as a quadrature modulator. 5.000.20 16 9 (1.0) 4.400.20 6.400.30 Unit: mm I Features * Low current consumption: 27 mA at VCC = 3 V * APC built-in * Excellent modulation precision characteristic 1 8 0.15 -0.05 +0.10 0 to 10 0.500.20 I Applications (0.225) 0.65 0.22 +0.10 -0.05 0.100.10 * Cellular telephone 1.200.20 Seating plane SSOP016-P-0225A I Block Diagram APC/BC GND Lo2R 10 7 8 GND Lo1 9 GND GND 12 VCC 15 P O 16 14 13 LPF 1 2 3 4 5 GND Q VCC Q I I 6 11 1 AN6091SA I Pin Descriptions Pin No. 1 2 3 4 5 6 7 8 VCC (MOD) Q input Q input I input I input GND Lo1 GND Description Pin No. 9 10 11 12 13 14 15 16 ICs for Mobile Communication Description Lo2R Lo2 APC/BS GND GND GND RF ouput VCC (up-mixer) I Absolute Maximum Ratings Parameter Supply voltage Supply current Power dissipation *2 *1 Symbol VCC ICC PD Topr Tstg Rating 4.2 60 252 -30 to +80 -55 to +125 Unit V mA mW C C Operating ambient temperature Storage temperature *1 Note) *1: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25C. *2: Ta = 80C. I Recommended Operating Range Parameter Supply voltage Symbol VCC Range 2.7 to 4.0 Unit V I Electrical Characteristics at Ta = 25C Parameter Outout level 1 Symbol PO1 Conditions Lo1 = 178 MHz, -15 dBm Lo2 = 1 607 MHz, -20 dBm VAPC = 2.3 V Lo1 = 178 MHz, -15 dBm Lo2 = 1 631 MHz, -20 dBm VAPC = 2.3 V Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 2.3 V No signal VAPC = 0 V Min -16 Typ -13 Max -10 Unit dBm Outout level 2 PO2 -16 -13 -10 dBm Current consumption ICC 27 35 mA Sleep current ISL 0 10 A 2 ICs for Mobile Communication I Electrical Characteristics at Ta = 25C (continued) Parameter Minimum output level Symbol PMIN Conditions Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 1.0 V Min Typ -50 AN6091SA Max -43 Unit dBm Note) VCC = 3.0 V IQ signal amplitude: 0.5 V[p-p] (single phase), DC bias: 1.7 V, /4 QPSK-modulated PO1 output frequency: 1 429.0025 MHz PO2 output frequency: 1 453.0025 MHz PMIN output frequency: 1 441.0025 MHz * Design reference data Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed. Parameter Carrier leak suppression (fLO2 - fLO1) Image leak suppression Symbol CL Conditions Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 2.3 V, IQ: DC offset adjustment Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 2.3 V, IQ: Level adjustment Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 2.3 V ditto ditto ditto ditto Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 1.0 V to 2.3 V Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 1.0 V/1.6 V Min Typ -35 Max Unit dBc IL -40 dBc Proximity spurious suppression DU -70 -65 dBc Base band distortion suppression Adjacent channel leak power suppression (30 kHz detuning) Adjacent channel leak power suppression (50 kHz detuning) Adjacent channel leak power suppression (100 kHz detuning) APC variable width BD BL1 BL2 BL3 LAPC 30 -40 -45 -70 37 -38 -60 -65 dBc dBc dBc dBc dB APC output level control sensitivity In-band output level deviation SAPC 46 dB/0.1 V P Lo1 = 178 MHz, -15 dBm -1.5 Lo2 = 1 607 MHz to 1 631 MHz, -20 dBm VAPC = 2.3 V Lo1 = 178 MHz, -15 dBm Lo2 = 1 619 MHz, -20 dBm VAPC = 2.3 V +1.5 dB Modulation precision EVM 2.0 %[rms] Note) Unless otherwise specified, VCC = 3.0 V IQ signal: 0.5 V[p-p] (single phase), DC bias: 1.7 V BL1, BL2, BL3, EVM: /4 QPSK-modulated CL, IL, DU, BD, LAPC , SAPC , P: PN9 stages 3 AN6091SA I Technical Data ICs for Mobile Communication APC control voltage characteristics -10 -20 -30 Ta = -30C, 25C Ta = 80C PO Ta = 25C, 80C -40 -50 -60 -70 -80 Ta = 25C Ta = 80C Ta = -30C ACP 30 kHz Ta = 80C Ta = -30C Ta = 25C, 80C Ta = -30C, 25C ACP 50 kHz Ta = -30C -30 -40 -50 -60 Ta = -30C -70 Ta = 25C, 80C -80 Circuit off DU -90 0 1 2 3 APC control voltage (V) Test circuit: "I Application Circuit Example" VCC = 3.0 V Ta = -30C, 25C, 80C Lo1: 178 MHz, -15 dBm Lo2: 1 619 MHz, -20 dBm IQ: 0.5 V[p-p] (single phase), 1.7 VDC /4, using PN9 stage continuous wave Note) 1. Unless otherwise specified, the test conditions are same as the electrical characteristics. 2. The above characteristics are theoretical values based on the IC design and are not guaranteed. 4 Adjacent channel leak power suppression ACP 30 kHz, 50 kHz (dBc) Proximity spurious suppression DU (dBc) 0 Output level PO (dBm) ICs for Mobile Communication I Application Circuit Example AN6091SA VAPC/BS PO 100 pF 16 15 14 13 12 11 Matsushita Electronic Components Co., Ltd. EHAFD1611 100 pF 1 pF 47 9 2 200 pF 1.0 k 47 10 1 000 pF Lo2 LPF 1 2 3 4 5 6 1 000 pF 330 pF 10 F Q VCC Q I I 330 pF 330 pF 330 pF Lo1 100 pF 7 8 5 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company. Please read the following notes before using the datasheets A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited. 2001 MAR |
Price & Availability of AN6091SA |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |