View MB89P485_212071.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MB89485
Single-Chip MCU Data Release Form (AH)
MDS-894-0030E Rev 1.1
Customer Name
Customer Contact
Customer Part No.
Fujitsu Part No.
MB89485 -
Application
History
New Release Update of Previous: MB89485 -
Automobile Engine Use Automobile Non-Engine Use Non-Automobile Use
(0) (1) (2)
Mask Option Item
Package Type
Contents of Selection
(0) SH-DIP-64 (1) LQFP-64
Notes
Mask ROM Data MCU Address Start Arbitrary End F F F FH C 0 0 0H Media Address H H H Program Data H H H ROL Address (Fujitsu Internal use) 4 0 0 0H H 7F F FH H H H
Fill out the above blanks in hexadecimal for our verification. Write the program data from Start address to End address.
- Satellite File Name: AHxxxx (Internal use Only for FMI/ FMG/FMAP) xxxx is ROM code No. assigned by Fujitsu.
Page 1 of 5
Mask Option Item
Main Clock Oscillation Type (OSC)
Contents of Selection
(1) 214/fC (2) 217/fC (3) 218/fC Crystal Resonator Ceramic Resonator FAR Resonator
Notes
Operation Frequency
Clock:
MHz
The frequency written here is regarded as the guaranteed operating frequency.
Stop Mode
(0) No (1) Yes
Booster circuit (KSV)
(0) No (1) Yes
Voltage Stabilization Time (POR)
(0) No (1) Yes (217/fC)
Page 2 of 5
Marking Form
Standard (See below:) Special * (0) (1)
Customer Spec No.
(Operating temperature., Operating supply voltage, Supply current, etc.)
Engineering samples have Standard marking with "ES" mark.
Fujitsu Part No.
Electrical Spec
Standard Special
FJ Logo F JAPAN Country of Origin Fujitsu Part No. Program Code No. Control Code
Mechanical Spec
Standard Special
MB89485 YYYY ZZZZ ZZZ
Date Code The height of Fujitsu Logo is 2.0mm. The other character except FJ logo is the gothic font and the height is the 1.2mm. The Control and Date Codes are the
Quality/Reliability
(Burn-in, Screening. etc.)
Standard Special
alphanumeric characters. The Program Code No. is assigned by Fujitsu.
Other Special Requirements
(Special marking proposal form etc.)
Page 3 of 5
Single-Chip MCU Data Release Form (F2MC-8L)
Rev.6.1
February 1994
Sample Requirement
Engineering Samples (ES) Free Engineering Samples: (Included in mask charge) Quantity Req'd FLT Date (MM/DD/YY) : : / / Units
Order Type
Non-Risk Order *1 (ROM verification is skipped) Risk Order *1 (ES confirmation is skipped.) Notes: *1 Refer to the next Page
Charged Engineering Sample (Additional ES) Quantity Req'd FLT Date (MM/DD/YY) Samples Price Package Type: : : / / Unit Ceramic Plastic Committed (P/O: ) Units
Application
Sales Price: (Including initial Ten Units of Engineering Samples) Committed Issued (P/O: )
Production Info.
Production Start: (MM/DD/YY) / / Initial Production: Units / Month Production Rate: Units / Month Unit Total Production: Units / Life ( Years) Production End: (MM/DD/YY) / / Expected Committed Expected: Committed Expected: Committed
Expected
to
Charged Commercial Samples (CS) Quantity Req'd FLT Date (MM/DD/YY) Samples Price Expected : : / / Units
Committed (P/O:
)
Originated by
Signature: Title Date : :
Production Info.
FMI/FMG/FMAP/FDI: PMM: PME: Scheduler: Kawasaki: Kawasaki:
Fujitsu declares that Fujitsu not disclose / sell your software and its mask ROM to a third party. However, even if its software from a third party may be completely or nearly the same with yours, Fujitsu doesn't assume any responsibility. In that case, whenever you find the software from a concerned third party infringe upon your right, Fujtisu concludes you have to settle an infringement problem with a concerned third party. Page 4 of 5
Single-Chip MCU Data Release Form
Rev.7.2 Aug 2001
Notice
1.PROGRAM ROM DATA
* The data format should be Intel HEX (except Intel extended hex), Motorola S1, or Motorola S2 formats. (Recommended Motorola S1/S2). And it should not have offset address. * The diskette save in the program ROM data is DOS 3.5 inch diskette (1.44MB). Or, electrical readable file (plain text) sending through e-mail. * The program ROM data should be filled in by the customer for all addresses from the START ADDRESS to the END ADDRESS. If the Physical Program ROM contains unused addresses after the END ADDRESS, the remainder of the unused addresses will be filled by default to FFH by Fujitsu * Fujitsu will sending back confirmation data in Motorola format which has processed and converted for Fujitsu's fabrication use. You may need simple offset adjustment requires at your confirmation.
2.SAMPLES
* ES (Engineering Sample) is guaranteed only for functional/electrical characteristics. Therefore, ES should not be used for reliability test. Also, marking form for ES is Fujitsu STANDARD unless otherwise requested * CS (Commercial Sample) is guaranteed for reliability equivalent to that of production parts.
3.ORDER TYPE
* Non-Risk Order * Risk Order :FJ makes ES after data release and starts production after ROM verification. :FJ starts production after ROM code confirmation. (ES confirmation is skipped.
4.CHANGING AFTER DATA RELEASE
If change required of released data, we will remake mask from the beginning. In such case, another mask charge and corrected DATA RELEASE FORM is necessary.
5.SOFTWARE AND ROM RIGHT
Fujitsu declares that Fujitsu not disclose / sell your software and its mask ROM to a third party. However, even if its software from a third party may be completely or nearly the same with yours, Fujitsu doesn't assume any responsibility. In that case, whenever you find the software from a concerned third party infringe upon your right, Fujtisu concludes you have to settle an infringement problem with a concerned third party.
Page 5 of 5

▲Up To Search▲

Price & Availability of MB89P485

	To Download MB89P485 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .