View M41T56_136307.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M41T56
512 bit (64b x8) Serial Access TIMEKEEPER(R) SRAM
s s
5V 10% SUPPLY VOLTAGE COUNTERS for SECONDS, MINUTES, HOURS, DAY, DATE, MONTH, YEARS and CENTURY YEAR 2000 COMPLIANT SOFTWARE CLOCK CALIBRATION AUTOMATIC POWER-FAIL DETECT and SWITCH CIRCUITRY I2C BUS COMPATIBLE 56 BYTES of GENERAL PURPOSE RAM ULTRA-LOW BATTERY SUPPLY CURRENT of 500nA LOW OPERATING CURRENT of 300A OPERATING TEMPERATURE of -40 to 85C AUTOMATIC LEAP YEAR COMPENSATION SPECIAL SOFTWARE PROGRAMMABLE OUTPUT PACKAGING INCLUDES a 28-LEAD SOIC and SNAPHAT(R) TOP (to be Ordered Separately)
VCC VBAT
SO8 (M) 150mil Width SNAPHAT (SH) Battery & Crystal
s s s
8 1
28 1
s s s
SOH28 (MH)
s s s s
Figure 1. Logic Diagram
s
Table 1. Signal Names
OSCI OCSO FT/OUT SDA SCL VBAT VCC VSS Oscillator Input Oscillator Output Frequency Test / Output Driver (Open Drain) Serial Data Address Input / Output Serial Clock Battery Supply Voltage Supply Voltage Ground
OSCI SCL M41T56
OSCO SDA FT/OUT
VSS
AI02304B
March 2000
1/19
M41T56
Figure 2A. SO8 Pin Connections Figure 2B. SOH28 Connections
OSCI OSCO VBAT VSS
M41T56 8 1 7 2 6 3 5 4
AI02306B
VCC FT/OUT SCL SDA
NC NC NC NC NC NC NC NC NC NC NC NC NC VSS
1 28 27 2 26 3 25 4 24 5 23 6 22 7 M41T56 21 8 20 9 19 10 18 11 17 12 16 13 15 14
AI03607
VCC NC FT/OUT NC NC NC NC NC SCL NC NC NC SDA NC
DESCRIPTION The M41T56 TIMEKEEPER (R) is a low power 512 bit static CMOS RAM organized as 64 words by 8 bits. A built-in 32.768 kHz oscillator (external crystal controlled) and the first 8 bytes of the RAM are used for the clock/calendar function and are configured in binary coded decimal (BCD) format. Addresses and data are transferred serially via a twoline bi-directional bus. The built-in address register is incremented automatically after each write or read data byte. The M41T56 clock has a built-in power sense circuit which detects power failures and automatically switches to the battery supply during power failures. The energy needed to sustain the RAM and clock operations can be supplied from a small lithium coin cell. Typical data retention time is in excess of 10years with a 50mAh 3V lithium cell. The M41T56 is supplied in 8 lead Plastic SOIC package or 28 lead SNAPHAT package. The 28 pin 330mil SOIC provides sockets with gold plated contacts at both ends for direct con-
nection to a separate SNAPHAT housing containing the battery and crystal. The unique design allows the SNAPHAT battery package to be mounted on top of the SOIC package after the completion of the surface mount process. Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal damage due to the high temperatures required for device surfacemounting. The SNAPHAT housing is keyed to prevent reverse insertion. The SOIC and battery/crystal packages are shipped separately in plastic antistatic tubes or in Tape & Reel form. For the 28 lead SOIC, the battery/crystal package (i.e. SNAPHAT) part number is "M4TxxBR12SHx". Caution: Do not place the SNAPHAT battery/crystal package "M4Txx-BR12SHx" in conductive foam since this will drain the lithium button-cell battery.
2/19
M41T56
Table 2. Absolute Maximum Ratings (1)
Symbol TA TSTG TSLD (2) VIO VCC IO PD Parameter Ambient Operating Temperature Storage Temperature (VCC Off, Oscillator Off) Lead Solder Temperature for 10 seconds Input or Output Voltages Supply Voltage Output Current Power Dissipation SNAPHAT SOIC Value -40 to 85 -40 to 85 C -55 to 125 260 -0.3 to 7 -0.3 to 7 20 0.25 C V V mA W Unit C
Note: 1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to the absolute maximum rating conditions for extended periods of time may affect reliability. 2. Soldering temperature not to exceed 260C for 10 seconds (total thermal budget not to exceed 150C for longer than 30 seconds).
CAUTION: Negative undershoots below -0.3V are not allowed on any pin while in the Battery Back-up mode. CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets.
OPERATION The M41T56 clock operates as a slave device on the serial bus. Access is obtained by implementing a start condition followed by the correct slave address (D0h). The 64 bytes contained in the device can then be accessed sequentially in the following order: 1. Seconds Register 2. Minutes Register 3. Century/Hours Register 4. Day Register 5. Date Register 6. Month Register 7. Years Register 8. Control Register 9 to 64. RAM
The clock continually monitors V CC for an out of tolerance condition. Should VCC fall below VPFD, the device terminates an access in progress and resets the device address counter. Inputs to the device will not be recognized at this time to prevent erroneous data from being written to the device from an out of tolerance system. When V CC falls below V BAT, the device automatically switches over to the battery and powers down into an ultra low current mode of operation to conserve battery life. Upon power-up, the device switches from battery to VCC at VBAT and recognizes inputs when VCC goes above V PFD volts.
3/19
M41T56
Figure 3. Block Diagram
1 Hz OSCI OSCILLATOR 32.768 kHz OSCO FT/OUT VCC VSS VBAT VOLTAGE SENSE and SWITCH CIRCUITRY DIVIDER
SECONDS MINUTES CENTURY/HOURS DAY DATE MONTH YEAR CONTROL
CONTROL LOGIC
SCL
SERIAL BUS INTERFACE
RAM (56 x 8) ADDRESS REGISTER
SDA
AI02566
Table 3. Register Map
Data Address D7 0 1 2 3 4 5 6 7 OUT ST X CEB X X X
(1)
D6
D5 10 Seconds 10 Minutes
D4
D3
D2
D1
D0
Function/Range BCD Format Seconds Minutes Century/Hour Day Date Month Year Control 00-59 00-59 0-1/00-23 01-07 01-31 01-12 00-99
Seconds Minutes Hours X Date Month Years Calibration Day
CB X X X
10 Hours X 10 Date X 10 M. X
10 Years FT S
Note: 1. When CEB is set to '1', CB will toggle from '0' to '1' or from '1' to '0' every 100 years (dependent upon the initial value set). When CEB is set to '0', CB will not toggle. Keys: S = SIGN Bit; FT = FREQUENCY TEST Bit; ST = STOP Bit; OUT = Output level; X = Don't care; CEB = Century Enable Bit; CB = Century Bit.
4/19
M41T56
Table 4. AC Measurement Conditions
Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages 5ns 0 to 3V 1.5V
0.8VCC 0.7VCC 0.3VCC
AI02568
Figure 4. AC Testing Load Circuit
Note that Output Hi-Z is defined as the point where data is no longer driven.
0.2VCC
2-WIRE BUS CHARACTERISTICS This bus is intended for communication between different ICs. It consists of two lines: one bi-directional for data signals (SDA) and one for clock signals (SCL). Both the SDA and the SCL lines must be connected to a positive supply voltage via a pull-up resistor. The following protocol has been defined: - Data transfer may be initiated only when the bus is not busy. - During data transfer, the data line must remain stable whenever the clock line is High. - Changes in the data line while the clock line is High will be interpreted as control signals. Accordingly, the following bus conditions have been defined: Bus not busy. Both data and clock lines remain High. Start data transfer. A change in the state of the data line, from High to Low, while the clock is High, defines the START condition. Stop data transfer. A change in the state of the data line, from Low to High, while the clock is High, defines the STOP condition. Table 5. Capacitance (1, 2) (TA = 25 C, f = MHz)
Symbol CIN COUT (3) tLP Input Capacitance (SCL) Output Capacitance (SDA, FT/OUT) Parameter
Data valid. The state of the data line represents valid data when after a start condition, the data line is stable for the duration of the High period of the clock signal. The data on the line may be changed during the Low period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a start condition and terminated with a stop condition. The number of data bytes transferred between the start and stop conditions is not limited. The information is transmitted byte-wide and each receiver acknowledges with a ninth bit. By definition, a device that gives out a message is called "transmitter", the receiving device that gets the message is called "receiver". The device that controls the message is called "master". The devices that are controlled by the master are called "slaves".
Min
Max 7 10
Unit pF pF s
Low-pass filter input time constant (SDA and SCL)
0.25
1
Note: 1. Effective capacitance measured with power supply at 5V. 2. Sampled, not 100% tested. 3. Outputs deselected.
5/19
M41T56
Table 6. DC Characteristics (TA = -40 to 85 C; VCC = 4.5V to 5.5V)
Symbol ILI ILO ICC1 ICC2 VIL VIH VOL VBAT (1) IBAT Parameter Input Leakage Current Output Leakage Current Supply Current Supply Current (Standby) Input Low Voltage Input High Voltage Output Low Voltage Battery Supply Voltage Battery Supply Current TA = 25C, VCC = 0V, Oscillator ON, VBAT = 3V IOL = 5mA, VCC = 4.5V 2.5 3 450 Test Condition 0V VIN VCC 0V VOUT VCC Switch Frequency = 100kHz SCL, SDA = VCC - 0.3V -0.3 3 100 1.5 VCC + 0.8 0.4 3.5 550 Min Typ Max 1 1 300 Unit A A A A V V V V nA
Note: 1. STMicroelectronics recommends the RAYOVAC BR1225 or BR1632 (or equivalent) as the battery supply.
Table 7. Power Down/Up Trip Points DC Characteristics (1) (TA = -40 to 85 C)
Symbol VPFD VSO Parameter Power-fail Deselect Voltage Battery Back-up Switchover Voltage Min 1.2 VBAT Typ 1.25 VBAT VBAT Max 1.285 VBAT Unit V V
Note: 1. All voltages referenced to VSS.
Table 8. Crystal Electrical Characteristics (Externally Supplied if using the SO8 package)
Symbol fO RS CL Parameter Resonant Frequency Series Resistance Load Capacitance 12.5 Min Typ 32.768 35 Max Unit kHz k pF
Note: Load capacitors are integrated within the M41T56. Circuit board layout considerations for the 32.768 kHz crystal of minimum trace lengths and isolation from RF generating signals should be taken into account.
STMicroelectronics recommends the KDS DT-38 Tuning Fork Type quartz crystal for industrial temperature operations. KDS can be contacted at 913-491-6825 or http://www.kdsj.co.jp for further information on this crystal type.
All SNAPHAT battery/crystal tops meet these specifications.
6/19
M41T56
Table 9. Power Down/Up AC Characteristics (TA = -40 to 85 C)
Symbol tPD tFB tRB tREC Parameter SCL and SDA at VIH before Power Down VPFD (min) to VSS VCC Fall Time VSS to VPFD (min) VCC Rise Time SCL and SDA at VIH after Power Up Min 0 300 100 10 Max Unit ns s s s
Figure 5. Power Down/Up Mode AC Waveforms
VCC VPFD VSO tPD SDA SCL tFB tRB tREC
IBAT DATA RETENTION TIME
AI00595
Acknowledge. Each byte of eight bits is followed by one acknowledge bit. This acknowledge bit is a low level put on the bus by the receiver, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed is obliged to generate an acknowledge after the reception of each byte. Also, a master receiver must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter.
The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is a stable Low during the High period of the acknowledge related clock pulse. Of course, setup and hold times must be taken into account. A master receiver must signal an end-of-data to the slave transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this case, the transmitter must leave the data line High to enable the master to generate the STOP condition.
7/19
M41T56
Table 10. AC Characteristics (TA = -40 to 85 C; VCC = 4.5V to 5.5V)
Symbol fSCL tLOW tHIGH tR tF tHD:STA tSU:STA tSU:DAT tHD:DAT (1) tSU:STO tBUF SCL Clock Frequency Clock Low Period Clock High Period SDA and SCL Rise Time SDA and SCL Fall Time START Condition Hold Time (after this period the first clock pulse is generated) START Condition Setup Time (only relevant for a repeated start condition) Data Setup Time Data Hold Time STOP Condition Setup Time Time the bus must be free before a new transmission can start 4 4.7 250 0 4.7 4.7 Parameter Min 0 4.7 4 1 300 Max 100 Unit kHz s s s ns s s ns s s s
Note: 1. Transmitter must internally provide a hold time to bridge the undefined region (300ns max.) of the falling edge of SCL.
WRITE MODE In this mode the master transmitter transmits to the M41T56 slave receiver. Bus protocol is shown in Figure 10. Following the START condition and slave address, a logic '0' (R/W = 0) is placed on the bus and indicates to the addressed device that word address An will follow and is to be written to the on-chip address pointer. The data word to be written to the memory is strobed in next and the internal address pointer is incremented to the next memory location within the RAM on the reception of an acknowledge clock. The M41T56 slave receiver will send an acknowledge clock to the master transmitter after it has received the slave address and again after it has received the word address and each data byte (see Figure 9). READ MODE In this mode, the master reads the M41T56 slave after setting the slave address (see Figure 11). Following the write mode control bit (R/W = 0) and the acknowledge bit, the word address A n is writ-
ten to the on-chip address pointer. Next the START condition and slave address are repeated, followed by the READ mode control bit (R/W = 1). At this point, the master transmitter becomes the master receiver. The data byte which was addressed will be transmitted and the master receiver will send an acknowledge bit to the slave transmitter. The address pointer is only incremented on reception of an acknowledge bit. The M41T56 slave transmitter will now place the data byte at address An + 1 on the bus. The master receiver reads and acknowledges the new byte and the address pointer is incremented to A n + 2. This cycle of reading consecutive addresses will continue until the master receiver sends a STOP condition to the slave transmitter. An alternate READ mode may also be implemented, whereby the master reads the M41T56 slave without first writing to the (volatile) address pointer. The first address that is read is the last one stored in the pointer, see Figure 12.
8/19
M41T56
Figure 6. Serial Bus Data Transfer Sequence
DATA LINE STABLE DATA VALID
CLOCK
DATA
START CONDITION
CHANGE OF DATA ALLOWED
STOP CONDITION
AI00587
Figure 7. Acknowledgment Sequence
CLOCK PULSE FOR ACKNOWLEDGEMENT 1 2 8 9
START SCLK FROM MASTER
DATA OUTPUT BY TRANSMITTER
MSB
LSB
DATA OUTPUT BY RECEIVER
AI00601
CLOCK OPERATION The eight byte clock register (see Table 3) is used to both set the clock and to read the date and time from the clock, in a binary coded decimal format. Seconds, Minutes, and Hours are contained within the first three registers. Bits D6 and D7 of clock register 2 (Hours Register) contain the CENTURY ENABLE Bit (CEB) and the CENTURY Bit (CB). Setting CEB to a '1' will cause CB to toggle, either from '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0', CB will not toggle. Bits D0 through D2 of register 3 contain the Day (day of week). Registers 4, 5 and 6 contain the Date (day of month), Month and Years. The final register is the Control Register (this is described in the Clock Calibration section). Bit D7 of register 0 contains the STOP Bit (ST). Setting this bit to a '1' will cause the oscillator
to stop. If the device is expected to spend a significant amount of time on the shelf, the oscillator may be stopped to reduce current drain. When reset to a '0' the oscillator restarts within one second. The seven Clock Registers may be read one byte at a time, or in a sequential block. The Control Register (Address location 7) may be accessed independently. Provision has been made to assure that a clock update does not occur while any of the seven clock addresses are being read. If a clock address is being read, an update of the clock registers will be delayed by 250ms to allow the read to be completed before the update occurs. This will prevent a transition of data during the read. Note: This 250ms delay affects only the clock register update and does not alter the actual clock time.
9/19
M41T56
Figure 8. Bus Timing Requirements Sequence
SDA tBUF tHD:STA tR SCL tHIGH P S tLOW tSU:DAT tHD:DAT tSU:STA SR P tSU:STO tF tHD:STA
AI00589
Note: P = STOP and S = START
Figure 9. Slave Address Location
R/W
START
SLAVE ADDRESS
A
1
1
0
1
0
0
0
AI00602
CLOCK CALIBRATION The M41T56 is driven by a quartz controlled oscillator with a nominal frequency of 32,768Hz. The devices are tested not to exceed 35ppm (parts per million) oscillator frequency error at 25C, which equates to about 1.53 minutes per month. With the calibration bits properly set, the accuracy of each M41T56 improves to better than +1/-2 ppm at 25C. The oscillation rate of any crystal changes with temperature (see Figure 14). Most clock chips compensate for crystal frequency and temperature shift error with cumbersome trim capacitors. The M41T56 design, however, employs periodic
counter correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit at the divide by 256 stage, as shown in Figure 13. The number of times pulses are blanked (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five bit Calibration byte found in the Control Register. Adding counts speeds the clock up, subtracting counts slows the clock down. The Calibration byte occupies the five lower order bits (D4-D0) in the Control register (Addr 7). This byte can be set to represent any value between 0 and 31 in binary form. Bit D5 is a Sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is loaded into the register, only the first 2 minutes in the 64 minutes cycle will be modified; if a binary 6 is loaded, the first 12 will be affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or -2.034 ppm of adjustment per calibration step in the calibration register. Assuming that the oscillator is in fact running at exactly 32,768Hz, each of the 31 increments in the Calibration byte would represent +10.7 or -5.35 seconds per month which corresponds to a total range of +5.5 or -2.75 minutes per month.
MSB
10/19
LSB
M41T56
Figure 10. Write Mode Sequence
START
BUS ACTIVITY: MASTER SDA LINE
S ACK
WORD ADDRESS (n) ACK
DATA n ACK
DATA n+1 ACK
DATA n+X
P ACK
BUS ACTIVITY: SLAVE ADDRESS
AI00591
Figure 11. Read Mode Sequence
START START
R/W
BUS ACTIVITY: MASTER SDA LINE
S ACK
WORD ADDRESS (n)
S ACK ACK
R/W
DATA n ACK
DATA n+1 ACK
AI00899
BUS ACTIVITY: SLAVE ADDRESS
SLAVE ADDRESS STOP
DATA n+X
P NO ACK
Figure 12. Alternate Read Mode Sequence
START
BUS ACTIVITY: MASTER SDA LINE
S ACK
DATA n ACK
DATA n+1 ACK ACK
DATA n+X
P NO ACK
BUS ACTIVITY: SLAVE ADDRESS
AI00895
STOP
R/W
STOP
R/W
11/19
M41T56
Figure 13. Clock Calibration
NORMAL
POSITIVE CALIBRATION
NEGATIVE CALIBRATION
AI00594B
Two methods are available for ascertaining how much calibration a given M41T56 may require. The first involves simply setting the clock, letting it run for a month and comparing it to a known accurate reference (like WWV broadcasts). While that may seem crude, it allows the designer to give the end user the ability to calibrate his clock as his environment may require, even after the final product is packaged in a non-user serviceable enclosure. All the designer has to do is provide a simple utility that accessed the Calibration byte. The second approach is better suited to a manufacturing environment, and involves the use of some test equipment. When the Frequency Test (FT) bit, the seventh-most significant bit in the Control Register, is set to a '1', and the oscillator is running at 32,768Hz, the FT/OUT pin of the device will toggle at 512Hz. Any deviation from 512Hz indicates the degree and direction of oscillator frequency shift at the test temperature.
For example, a reading of 512.01024Hz would indicate a +20ppm oscillator frequency error, requiring a -10(XX001010) to be loaded into the Calibration Byte for correction. Note that setting or changing the Calibration Byte does not affect the Frequency test output frequency. OUTPUT DRIVER PIN When the FT bit is not set, the FT/OUT pin becomes an output driver that reflects the contents of D7 of the control register. In other words, when D6 of location 7 is a zero and D7 of location 7 is a zero and then the FT/OUT pin will be driven low. Note: The FT/OUT pin is open drain which requires an external pull-up resistor. POWER-ON DEFAULTS Upon initial application of power to the device, the FT bit will be set to a '0' and the OUT bit will be set to a '1'. All other Register bits will initially power-on in a random state.
12/19
M41T56
Figure 14. Crystal Accuracy Across Temperature
Frequency (ppm) 20 0 -20 -40 -60 -80 -100 -120 -140 -160 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 F = -0.038 ppm (T - T )2 10% 0 F C2 T0 = 25 C
Temperature C
AI00999
13/19
M41T56
Table 11. Ordering Information Scheme
Example: Device Type M41T Package M = SO8 150mils width MH = SOH28 Temperature Range 6 = -40 to 85 C Shipping Method for SO blank = Tubes TR = Tape & Reel M41T56 M 6 TR
Note: The SOIC package (SOH28) requires the battery package (SNAPHAT) which is ordered separately under the part number "M4Txx-BR12SHx" in plastic tube or "M4Txx-BR12SHxTR" in Tape & Reel form. Caution: Do not place the SNAPHAT battery package "M4Txx-BR12SHx" in conductive foam since this will drain the lithium button-cell battery.
For a list of available options or for further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you.
Table 12. Revision History
Date March 1999 12/23/99 03/21/00 First Issue SOH28 package added Series Resistance Max Value Changed (Table 8) Revision Details
14/19
M41T56
Table 13. SO8 - 8 pin Plastic Small Outline, 150 mils body width, Package Mechanical Data
mm Symb Typ A A1 B C D E e H h L N CP 1.27 Min 1.35 0.10 0.33 0.19 4.80 3.80 - 5.80 0.25 0.40 0 8 0.10 Max 1.75 0.25 0.51 0.25 5.00 4.00 - 6.20 0.50 0.90 8 0.050 Typ Min 0.053 0.004 0.013 0.007 0.189 0.150 - 0.228 0.010 0.016 0 8 0.004 Max 0.069 0.010 0.020 0.010 0.197 0.157 - 0.244 0.020 0.035 8 inches
Figure 15. SO8 - 8 pin Plastic Small Outline, 150 mils body width, Package Outline
h x 45 A C B e D CP
N
E
1
H A1 L
SO-a
Drawing is not to scale.
15/19
M41T56
Table 14. SOH28 - 28 lead Plastic Small Outline, 4-socket battery SNAPHAT, Package Mechanical Data
mm Symb Typ A A1 A2 B C D E e eB H L N CP 1.27 0.05 2.34 0.36 0.15 17.71 8.23 - 3.20 11.51 0.41 0 28 0.10 Min Max 3.05 0.36 2.69 0.51 0.32 18.49 8.89 - 3.61 12.70 1.27 8 0.050 0.002 0.092 0.014 0.006 0.697 0.324 - 0.126 0.453 0.016 0 28 0.004 Typ Min Max 0.120 0.014 0.106 0.020 0.012 0.728 0.350 - 0.142 0.500 0.050 8 inches
Figure 16. SOH28 - 28 lead Plastic Small Outline, 4-socket battery SNAPHAT, Package Outline
A2 B e
A C eB CP
D
N
E
H A1 L
1 SOH-A
Drawing is not to scale.
16/19
M41T56
Table 15. SH - 4-pin SNAPHAT Housing for 48 mAh Battery & Crystal, Package Mechanical Data
mm Symb Typ A A1 A2 A3 B D E eB L 0.46 21.21 14.22 3.20 2.03 6.73 6.48 Min Max 9.78 7.24 6.99 0.38 0.56 21.84 14.99 3.61 2.29 0.018 0.835 0.560 0.126 0.080 0.265 0.255 Typ Min Max 0.385 0.285 0.275 0.015 0.022 0.860 0.590 0.142 0.090 inches
Figure 17. SH - 4-pin SNAPHAT Housing for 48 mAh Battery & Crystal, Package Outline
A1
A2 A A3
eA D
B eB
L
E
SHTK-A
Drawing is not to scale.
17/19
M41T56
Table 16. SH - 4-pin SNAPHAT Housing for 120 mAh Battery & Crystal, Package Mechanical Data
mm Symb Typ A A1 A2 A3 B D E eB L 0.46 21.21 17.27 3.20 2.03 8.00 7.24 Min Max 10.54 8.51 8.00 0.38 0.56 21.84 18.03 3.61 2.29 0.018 0.835 0.680 0.126 0.080 0.315 0.285 Typ Min Max 0.415 0.335 0.315 0.015 0.022 0.860 0.710 0.142 0.090 inches
Figure 18. SH - 4-pin SNAPHAT Housing for 120 mAh Battery & Crystal, Package Outline
A1
A2 A A3
eA D
B eB
L
E
SHTK-B
Drawing is not to scale.
18/19
M41T56
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics (R) 2000 STMicroelectronics - All Rights Reserved All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com
19/19

▲Up To Search▲

Price & Availability of M41T56

	To Download M41T56 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .